Similar models
grabcad
free
Gudgeon Pin or Piston Pin or Wrist Pin
...gudgeon pin or piston pin or wrist pin
grabcad
gudgeon pin or piston pin or wrist pin
grabcad
free
PIN, TAPER PIN
...pin, taper pin
grabcad
taper pin, pin
3dwarehouse
free
Pin
...pin
3dwarehouse
pin #pin
grabcad
free
HEADER PIN - MALE HEADER PIN - HEADER STRIP PIN
...header pin - male header pin - header strip pin
grabcad
header pin, single row header pin, male header pin
grabcad
free
Clevis Pin with Cotter Pin
...clevis pin with cotter pin
grabcad
clevis pin with cotter pin
grabcad
free
Thumb Pin
...thumb pin
grabcad
thumb pin / push pin / drawing pin
grabcad
free
Hair Pin Cotter Pin
...hair pin cotter pin
grabcad
hair pin cotter pin
grabcad
free
Board Pin / Push Pin
...board pin / push pin
grabcad
board pin / push pin
grabcad
free
Pullout Pin, Hitch Pin
...pullout pin, hitch pin
grabcad
hitch pin, pullout pin
grabcad
free
Pin 5
...pin 5
grabcad
pin 5
pin to pin: 0.1 inch(2.54mm)
Jltott
thingiverse
free
P-clip by jltott
...p-clip by jltott
thingiverse
simple p-clip to tie cables together.
thingiverse
free
Nozzle by jltott
... could be smaller but then it has problems printing. cleaned out the hole in the nozzle with an acupuncture needle - worked fine.
thingiverse
free
Freezer handle by jltott
...mportant thing is the hole centres are 175mm, 4mm wide slots for 4mm self tappers. top face is flat so print with top face on bed
thingiverse
free
Test plate with hinged flap by jltott
...t for dimensional accuracy testing), a pivot pin and the flap. interest only, no value other than seeing what 3d printing can do.
thingiverse
free
Cork screw improvement by jltott
...k collar, slide out clear plastic spacer and add new spacer between bottom of spring and top of clear plastic spacer. re-assemble
thingiverse
free
Spool dividers by jltott
...nwind when a different filament is being used and perhaps even some way of setting the spacing.
really an exercise in 3d printing
thingiverse
free
Samsung S7 Edge case and dashboard mount by jltott
... cut away too much and it is not strong enough. if the uprights went all the way around the phone it would probably be quite good
Hinge
3d_export
$10
hinge and hinge 148 specifications
...hinge and hinge 148 specifications
3dexport
hinge and hinge (148 specifications)
3d_export
free
hinge
...hinge
3dexport
hinge model
3ddd
free
hinges
...hinges
3ddd
крепление
two types of hinge for furniture.
3d_export
$6
Hinge
...hinge
3dexport
hinge assembly render 3d modelling design
turbosquid
$19
Hinges
...
turbosquid
royalty free 3d model hinges for download as max on turbosquid: 3d models for games, architecture, videos. (1453553)
turbosquid
$19
Hinges
...
turbosquid
royalty free 3d model hinges for download as max on turbosquid: 3d models for games, architecture, videos. (1447125)
3d_export
$5
hinge 1
...hinge 1
3dexport
hinge 1
3d_export
$5
hinge 2
...hinge 2
3dexport
hinge 2
3d_export
$5
hinge 3
...hinge 3
3dexport
hinge 3
3d_export
$5
hinge 4
...hinge 4
3dexport
hinge 4