Thingiverse
Heatbed leveling screw M3 by Hustensaft
by Thingiverse
Last crawled date: 3 years ago
This litle piece helps you leveling your heatbed much easier and accurate!
You need a simple M3 nut which fits perfekt insight the printed leveling bolt.
Easiest way to place the nut is to take an approx. 40mm M3 screw, place the nut in front and give it a slight punch with a hammer, whilst placing it insight the bolt.
Then remove the screw and your leveling screw is ready to use.
I was tired to brake my fingers with the original tiny wheels. The bigger levelingscrew is way much easier to handle and your headbed can be leveled more accurate.
BTW: I use a 0.4mm nozzel so I have to shimm it 0.2mm above the heatbed. Easy trick is to use a sheet of paper, fold it in the middle and place it between nozzel an heatbed. Thickness of a usuall paper is 0.10mm. So if you take it double it works out perfekt :-)
You need a simple M3 nut which fits perfekt insight the printed leveling bolt.
Easiest way to place the nut is to take an approx. 40mm M3 screw, place the nut in front and give it a slight punch with a hammer, whilst placing it insight the bolt.
Then remove the screw and your leveling screw is ready to use.
I was tired to brake my fingers with the original tiny wheels. The bigger levelingscrew is way much easier to handle and your headbed can be leveled more accurate.
BTW: I use a 0.4mm nozzel so I have to shimm it 0.2mm above the heatbed. Easy trick is to use a sheet of paper, fold it in the middle and place it between nozzel an heatbed. Thickness of a usuall paper is 0.10mm. So if you take it double it works out perfekt :-)
Similar models
thingiverse
free
Big leveling wheel for 3 point leveling by Fort_Design
...heel for the other two leveling points. also for m3 nut
diameter: 25mm
use some superglue to hold the nuts in place if necessary.
thingiverse
free
Bed leveling thumb screw with embedded nut. by PeterMadsen
... thumbscrew has an embedded m3 nut placed there at mid-print, so it can be a bit tricky to make, please refer to the instrucions.
thingiverse
free
Anet A8 Hotbed Spring Cap (with m3 nut spacing) by Santonian
...printed this in pla which works fine for me, but if you regulary use a hotter hotbed, you might want to print this in abs or petg
thingiverse
free
Wide M3 Nut by mehmetacom
...wide m3 nut by mehmetacom
thingiverse
with this you can level your heatbed easily :)
thingiverse
free
print bed thumb wheel by tanasibob
...lt with a washer to seat it properly... make this one of your first mods, you will not be sorry (if you dont have auto leveling.)
thingiverse
free
MPCNC -Add On- Dewalt DW660 Mount M3 Captive Nut Remix by Humanisticnick
... preferred) and 6xm3 20mm screws
so use your existing hardware and avoid yelling at a little tiny nut that keeps slipping. yay :)
thingiverse
free
Zonestar P802 heatbed adjustment wheel and spring guide by BomanXIX
...wheels takes in a m3 nut and make it easier to level the bed.
the spring guides stop the bed leveling springs from moving around.
thingiverse
free
Anet A8 3-point heatbed leveling addon by Kotvic
...and watch first layer to be just right. if it is too close or too far, adjust origin position in your firmware or adjust endstop.
thingiverse
free
Anycubic Kossel Plus Adjustable Heatbed Mount by bartigas
... the mount. springs can be sourced from home depot, amazon, ebay, etc.
thanks to themanmall and originally guco for the concept.
thingiverse
free
[Heated Scr3w Duo] - Heatbed leveler by mr2clean
...n add-on to m3 screw that holds the heated bed.
it has the option to use two m3 nuts so not to lose tention.
license, beerware :)
Hustensaft
thingiverse
free
Radioator Hook by Hustensaft
...radioator hook by hustensaft
thingiverse
please check on the drawing if this fits to your radiator.
thingiverse
free
Axii Alien Mount by Hustensaft
...axii alien mount by hustensaft
thingiverse
improvements: lays flat on print surface. no suports required.
thingiverse
free
Ummagawd Remix Trunk Axii by Hustensaft
...ummagawd remix trunk axii by hustensaft
thingiverse
solide axii trunk
thingiverse
free
Bit holder for 6.4mm bits by Hustensaft
...bit holder for 6.4mm bits by hustensaft
thingiverse
jet another bit holder for the typical 6.4mm bits.
thingiverse
free
Pull Switch Bracket by Hustensaft
...tch bracket by hustensaft
thingiverse
help your pull switch mounting better and prevent it from twisting when you pull the rope.
thingiverse
free
Hooks for banister by Hustensaft
...e in any kind of purpose.
i redesigned them to hang them on my barnister.
in my case the pole bar is square with a width of 20mm.
thingiverse
free
Catan Tokens with inlay by Hustensaft
... tokens with seperat printed number inlays in any colour you like.
numbers have different sizes according to their propabilities.
thingiverse
free
Nema 17 mount by Hustensaft
...rse
mountplate for a usual nema17 stepper.
you might need:
4 x m3 x 40mm screw (for nema17)
2 x m5 x 16mm screw
2 x m5 hammernut
thingiverse
free
MTD Canopy for small servo by Hustensaft
...39;t used it yet.
was thingking about mounting a pan/tilt mechanism to it like this one https://www.thingiverse.com/thing:2461310
thingiverse
free
Bracket for power cable by Hustensaft
...it and prevent for unexpected tensions.
2 x 5mm screws and hammernuts required
turn it 90° an print it upright staying on a side.
Heatbed
thingiverse
free
HeatBed by moreken
...heatbed by moreken
thingiverse
heatbed for my printer3d "moredelta"
thingiverse
free
heatbed (double heatbed) holder by Vo_Van_163
... bigger size than work desk. this holder - is good solution for me/ and also this is a good solution for double hotbed regulation
thingiverse
free
Heatbed Spatula by Brabus453
... spatula by brabus453
thingiverse
heatbed spatula
this is a simple spatula to scrape the heatbed from the first layer residues.
thingiverse
free
Heatbed Mount for round Heatbeds by OliverReinecke
...y bottom board to fix the heatbed-mount. but of coursse there are lots of alternatives to do this... its up to you. hope it helps
thingiverse
free
Heatbed plane test
...eds ... this simple object allows to see where the bonding of the object and the flatness of the heatbed might not be optimal ...
thingiverse
free
Heatbed Knob by Sp0nge
...heatbed knob by sp0nge
thingiverse
craftbot plus heatbed knob
print it in abs and put a nut inside.
thingiverse
free
Heatbed cable cover
... the heatbed when i placing the pei sheet.
so i designed this small cover, it clips right down over the +/- screws on the heatbed
thingiverse
free
Heatbed Mosfet controller by oscar_diciomma
...heatbed mosfet controller by oscar_diciomma
thingiverse
heatbed mosfet controller
thingiverse
free
Parametric Heatbed Clamp by verglor
...y verglor
thingiverse
minimalistic heatbed clamps that do not get in way of nozzle.
can be customized for any heatbed thickness.
thingiverse
free
Heatbed support
...ail
heatbed size 328mm
use m5x10 with washers or m5x8 for the 20x20 profile
m4 for heatbed
can be use with wells of 45mm of diam.
M3
3d_ocean
$39
BMW M3
...bmw m3
3docean
3d model bmw m3 car
bmw m3
3d_export
$5
m3 e92 coupe
...m3 e92 coupe
3dexport
cars m3 e92 coupe
turbosquid
$7
Spaceship M3
... free 3d model spaceship m3 for download as jpg, max, and obj on turbosquid: 3d models for games, architecture, videos. (1375862)
3ddd
$1
BMW M3
...ель автомобиля bmw m3 e30, выполненная по оригинальным чертежам. модель высокополигональная. также смоделированы диски фирмы bbs.
turbosquid
$50
M3 Halftrack
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$39
M3 Bradley
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$15
M3 Chair
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$9
M3 Stuart
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$50
Bmw m3 3D Model
...bmw m3 3d model
3dexport
bmw m3
bmw m3 3d model uae00boy 59598 3dexport
3d_export
$39
Bmw M3 3D Model
...bmw m3 3d model
3dexport
bmw m3
bmw m3 3d model basit321 17551 3dexport
Leveling
design_connected
$11
Levels
...levels
designconnected
one nordic levels computer generated 3d model. designed by form us with love.
design_connected
$7
Level
...level
designconnected
zanotta level shelves and storage computer generated 3d model. designed by arik levy.
turbosquid
$29
level
...ty free 3d model level for download as 3ds, obj, c4d, and fbx on turbosquid: 3d models for games, architecture, videos. (1272856)
turbosquid
$1
level
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Mario level
...mario level
3dexport
mario level low quality for fun videos
3ddd
$1
LEVELS OF DISCOVERY
...етская мебель "levels of discovery". rab10003 princess mini rocker
кресло-качалка (мини) "принцесса навсегда"
3d_export
$19
level design
...level design
3dexport
you can use this design (level design) in your own game.
turbosquid
$60
Desert level
...squid
royalty free 3d model desert level for download as fbx on turbosquid: 3d models for games, architecture, videos. (1208131)
turbosquid
$15
Transit Level
...quid
royalty free 3d model transit level for download as max on turbosquid: 3d models for games, architecture, videos. (1158112)
turbosquid
$14
Districts Level
...id
royalty free 3d model districts level for download as max on turbosquid: 3d models for games, architecture, videos. (1408410)
Screw
3d_export
$5
screw
...screw
3dexport
screw
turbosquid
$29
Screw driver and screws
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_ocean
$2
Screw
... steel twist wood screw
screw 3d model in 2 different materials real world scale rendered with mental ray file formats: .max .obj
3d_ocean
$4
Screw
...n
3d bolt male mechanic metal nut parts prop propeller schraube schraubenmutter screw steel twist
screw 3d model, clean modeling.
turbosquid
$2
screw
...crew
turbosquid
royalty free 3d model screw for download as on turbosquid: 3d models for games, architecture, videos. (1198271)
turbosquid
free
Screw
...screw
turbosquid
free 3d model screw for download as obj on turbosquid: 3d models for games, architecture, videos. (1240851)
3d_ocean
$2
Frame Screw
...frame screw
3docean
construction screw
a frame screw and plug.
turbosquid
$27
screw
...w
turbosquid
royalty free 3d model screw for download as max on turbosquid: 3d models for games, architecture, videos. (1334064)
turbosquid
$20
SCREW
...
turbosquid
royalty free 3d model screw for download as sldas on turbosquid: 3d models for games, architecture, videos. (729733)
turbosquid
$1
Screws
...
turbosquid
royalty free 3d model screws for download as max on turbosquid: 3d models for games, architecture, videos. (1640360)