Thingiverse
Heatbed Isolation (Tevo Tarantula) by bytezar
by Thingiverse
Last crawled date: 3 years ago
OpenSCAD files are available on my github repository:https://github.com/bytezar/heatbed-isolation
Parts:
Thick cork mat (thickness: 6mm): https://www.castorama.pl/produkty/wykonczenie/tapety-i-wykonczenie-powierzchni/artykuly-korkowe/plyta-korkowa-6-mm.html
Thin cork place mat: http://www.ikea.com/gb/en/products/textiles-rugs/table-linen/avskild-place-mat-cork-art-40281654/
Large binder clips (Length: 2 inches, 51 mm): https://www.amazon.com/ACCO-Binder-Clips-Large-72100/dp/B002VD6BLG/
Glass on heatbed attached by small binder clip
4x screw M3 30 mm
Tools:
Sharp knife
Driller-driver
Drill bits: 3 mm, 7 mm, 9 mm
The ruler and pen
Process:
Print 4 parts (2x part "no hole", 1x "hole left", 1x "hole right", this hole is for wires).
Use driller-driver and 3 mm bit to improve horizontal holes.
Screw it using M3 screws (30 mm length).
Cut two 24,8 mm squares in 6mm cork mat.
Cut two 24,8 mm squares in 2mm cork mat.
In one thin cork mat cut holes for small clip binders (green in the picture) and wires below the table (see the picture).
Put 3 layers of cork mat into printed parts. At the bottom put thick cork mat and then two thin ones.
Use driller-driver and 9 mm bits to make holes (in cork) for 4x bed springs.
Use driller-driver and 7 mm bits to make hole (in cork) for bed wires.
In second thick cork mat cut 22 mm square (in the middle) for heat bed.
Place heat bed with attached glass (don’t forget to remove hooks?? from binder clips).
Put second thick cork (with big hole), which should fill gaps between hotbed and printed parts.
You can also cut another 25,4 mm cork square in thick mat. When you printer is warming, cover hot bed. In this way heat bed will reach proper temperature faster :-)
Remarks:
Maybe you also need holes in second thin cork mat, but holes only for small clip binders.
In OpenSCAD there is value latchOffset. I don't know whether this value is proper. I printed without this offset and I had to use sand paper to bigger space.
I don't know whether variable "wireHoleDiameter" is proper. I also printed without it. I had to use driller-driver to make hole for wires.
Parts:
Thick cork mat (thickness: 6mm): https://www.castorama.pl/produkty/wykonczenie/tapety-i-wykonczenie-powierzchni/artykuly-korkowe/plyta-korkowa-6-mm.html
Thin cork place mat: http://www.ikea.com/gb/en/products/textiles-rugs/table-linen/avskild-place-mat-cork-art-40281654/
Large binder clips (Length: 2 inches, 51 mm): https://www.amazon.com/ACCO-Binder-Clips-Large-72100/dp/B002VD6BLG/
Glass on heatbed attached by small binder clip
4x screw M3 30 mm
Tools:
Sharp knife
Driller-driver
Drill bits: 3 mm, 7 mm, 9 mm
The ruler and pen
Process:
Print 4 parts (2x part "no hole", 1x "hole left", 1x "hole right", this hole is for wires).
Use driller-driver and 3 mm bit to improve horizontal holes.
Screw it using M3 screws (30 mm length).
Cut two 24,8 mm squares in 6mm cork mat.
Cut two 24,8 mm squares in 2mm cork mat.
In one thin cork mat cut holes for small clip binders (green in the picture) and wires below the table (see the picture).
Put 3 layers of cork mat into printed parts. At the bottom put thick cork mat and then two thin ones.
Use driller-driver and 9 mm bits to make holes (in cork) for 4x bed springs.
Use driller-driver and 7 mm bits to make hole (in cork) for bed wires.
In second thick cork mat cut 22 mm square (in the middle) for heat bed.
Place heat bed with attached glass (don’t forget to remove hooks?? from binder clips).
Put second thick cork (with big hole), which should fill gaps between hotbed and printed parts.
You can also cut another 25,4 mm cork square in thick mat. When you printer is warming, cover hot bed. In this way heat bed will reach proper temperature faster :-)
Remarks:
Maybe you also need holes in second thin cork mat, but holes only for small clip binders.
In OpenSCAD there is value latchOffset. I don't know whether this value is proper. I printed without this offset and I had to use sand paper to bigger space.
I don't know whether variable "wireHoleDiameter" is proper. I also printed without it. I had to use driller-driver to make hole for wires.
Similar models
thingiverse
free
Heat Bed Wire Mount by chuteroo
...tled for epoxy, but would be happy to see someone succeed in fastening the assembly with a structural rather than adhesive means.
thingiverse
free
Heat_bed_clip_Thin type by kazenokakasi
...ip for heat bed with a thickness of 2 mm.
clip width is 30 mm.
when printing with vertical clip, it will be beautifully finished.
thingiverse
free
Heatbed Clip by JamesK1
...ted the binder clips that rattle during prints.
be sure to print with petg or abs or something with high temp tolerance. not pla.
thingiverse
free
Anet A8 glass+heatbed clip by GErt09Nel
...anet a8 glass+heatbed clip by gert09nel
thingiverse
clip to secure glass bed to heat bed
glass is 4mm thick
thingiverse
free
Clip for Holding down Glass + Bed + PEI + Cork by Tailslide
... thin as i could but if you have a bed levelling sensor or fan very close to the surface take care it doesn't bump the clips.
thingiverse
free
Glass and Heatbed Clips by bruckj
...01-24 update:
cleaned up sketchup file.
added a captive nut clip to replace the "knobs", this makes adjustments easier
thingiverse
free
Anet A8 Glass and Heatbed clip for 3/32" thick by YakRuski
...tra tight fit, difficult to put on but stays tight. this is made for a standard aluminum heat bed and 3/32" thick glass bed.
thingiverse
free
Glass clamp and heat bed for Mini Kossel by micolo
... on parate project. i used 1mm aluminium only on top and other "layers" was cut from laminate (1mm thick) and 2mm cork.
thingiverse
free
Tronxy X5S Glass Bed Corner Clip by fuzzyunicorn
...will probably work with other printers that have a similar heat bed. i have uploaded the openscad file if...
thingiverse
free
Heatbed Glassplate Holder 5.5mm 220x220mm by Keigun
...ently interfere with the clips.
this object is not print ready.
clips are made for 220x220mm print beds and a thickness of 5.5mm.
Bytezar
thingiverse
free
Conversion: laptop screen to monitor by bytezar
...conversion: laptop screen to monitor by bytezar
thingiverse
about conversion:https://youtu.be/hhtvcvulm2i.
thingiverse
free
Battery management system (BMS) holder by bytezar
...bms bought on aliexpress:https://www.aliexpress.com/item/10s-15a-bms-for-36v-li-ion-battery/1195130789.html
i used 2.5 mm screws.
thingiverse
free
Spot welder (controller holder) by bytezar
...ds a 9v transformer:https://www.aliexpress.com/item/power-transformer-ac9v-spot-welder-matched-power-transformer/32807729529.html
thingiverse
free
Brake sensor (magnet ring holder) by bytezar
...fitting-gear/738588_32606950130.html
put ring on cylinder and glue it to second part.
i used zip-tie to bound it to brake handle.
thingiverse
free
Valve wall hole cover by bytezar
...2 inch).
original valve was in the plaster of wall, so to replace it i had to make hole.
i created this model to covet that hole.
thingiverse
free
Spoolholder based on M8 rod and bearing by bytezar
...hamowane-din-985-m8.html#product
2x m8 screw 30 mm
2x m8 connector nut:https://www.tim.pl/nakretka-lacznikowa-nl-m8-650203-100szt
thingiverse
free
Light installation (from Li-on batteries) by bytezar
...p://allegro.pl/konektor-listwa-ak-ark-5-08mm-h-10mm-2pin-zielona-i5190554060.html
2x screws m3 (25mm)
2x screw m2.5
2x switch 12v
thingiverse
free
Dual Blower/Radial Fan Duct Mount Remix (Tevo Tarantula with different X carriage) by bytezar
...n standard ones (see green arrays in the picture).
my version of dual blower is more solid then standard one (walls are thicker).
Heatbed
thingiverse
free
HeatBed by moreken
...heatbed by moreken
thingiverse
heatbed for my printer3d "moredelta"
thingiverse
free
heatbed (double heatbed) holder by Vo_Van_163
... bigger size than work desk. this holder - is good solution for me/ and also this is a good solution for double hotbed regulation
thingiverse
free
Heatbed Spatula by Brabus453
... spatula by brabus453
thingiverse
heatbed spatula
this is a simple spatula to scrape the heatbed from the first layer residues.
thingiverse
free
Heatbed Mount for round Heatbeds by OliverReinecke
...y bottom board to fix the heatbed-mount. but of coursse there are lots of alternatives to do this... its up to you. hope it helps
thingiverse
free
Heatbed plane test
...eds ... this simple object allows to see where the bonding of the object and the flatness of the heatbed might not be optimal ...
thingiverse
free
Heatbed Knob by Sp0nge
...heatbed knob by sp0nge
thingiverse
craftbot plus heatbed knob
print it in abs and put a nut inside.
thingiverse
free
Heatbed cable cover
... the heatbed when i placing the pei sheet.
so i designed this small cover, it clips right down over the +/- screws on the heatbed
thingiverse
free
Heatbed Mosfet controller by oscar_diciomma
...heatbed mosfet controller by oscar_diciomma
thingiverse
heatbed mosfet controller
thingiverse
free
Parametric Heatbed Clamp by verglor
...y verglor
thingiverse
minimalistic heatbed clamps that do not get in way of nozzle.
can be customized for any heatbed thickness.
thingiverse
free
Heatbed support
...ail
heatbed size 328mm
use m5x10 with washers or m5x8 for the 20x20 profile
m4 for heatbed
can be use with wells of 45mm of diam.
Tarantula
turbosquid
$5
tarantula
...rbosquid
royalty free 3d model tarantula for download as c4d on turbosquid: 3d models for games, architecture, videos. (1690032)
3d_ocean
$8
Tarantula
...rantula 3d model. perfect for animations or still image. textures psd and jpeg files included. modelled using autodesk maya 2011.
turbosquid
$50
tarantula
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$45
Tarantula
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$12
Spider black widow tarantula tarantula Insects
... black widow tarantula tarantula insects for download as max on turbosquid: 3d models for games, architecture, videos. (1582101)
3ddd
$1
Журнальный столик - tarantula
... бионика , tarantula
журнальный столик tarantula
h=600
d=2000
3d_export
$35
Tarantula
...: zbrush 3ds max ztool obj fbx dae 3ds stl properties : 20*20*8 production time : 23 hours 328 gram models are drawn with zbrush.
3d_ocean
$20
Tarantula spider
...igged, animated, uv textured. particle system for the fur. very easy to animate. a 250 frames animation is available in the pack.
turbosquid
$45
Tarantula Spider
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
spider tarantula
...spider tarantula
3dexport
3d model of a steppe spider for your ideas and projects.
Tevo
thingiverse
free
TEVO Logo by limwenyao
...verse
tevo logo - for customizing your builds to look cooler with the tevo logo! pdf version is editable with adobe illustrator.
thingiverse
free
Tevo Tornado e3d Tevo Flash Style fan Mount by DemolitionX
...an mount by demolitionx
thingiverse
just messing around and made a tevo flash style fan mount for the e3d v6 on the tevo tornado
thingiverse
free
BODEN TUBE CLAMP FOR TEVO TARANTULA PRO AND TEVO TORNADO
... and tevo tornado
thingiverse
bodwen tube clamp. printable adjustable tension clamp for tevo tarantula pro and tornado extruder.
thingiverse
free
TEVO Tornado Model by JMDesigns
...tevo tornado model by jmdesigns
thingiverse
tevo tornado model
thingiverse
free
Tevo Tarantula FanDuct by hkgary_g
...tevo tarantula fanduct by hkgary_g
thingiverse
fanduct for tevo tarantula
thingiverse
free
FAN TEVO TARANTULA by llprokall
...fan tevo tarantula by llprokall
thingiverse
fan tevo tarantula
thingiverse
free
Tevo Tarantula filament by Xbertus
...tevo tarantula filament by xbertus
thingiverse
suport for filamente tevo tarantula
thingiverse
free
TEVO Top Brackets by _Godoy_
...tevo top brackets by _godoy_
thingiverse
top brackets for tevo tarantula
thingiverse
free
Tevo Tarantula Spool Holder
...tevo tarantula spool holder
thingiverse
strong spool holder for tevo tarantula
thingiverse
free
tevo tarantula spacer by poundskinnyboy
...tevo tarantula spacer by poundskinnyboy
thingiverse
it's a tevo tarantula spacer
Isolation
turbosquid
$5
isolator
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
BOSA / ISOLE
...bosa / isole
3ddd
bosa
пять ваз от bosa, коллекция isole. 120,000 полигонов.
3ddd
free
Isole by bosa
...isole by bosa
3ddd
bosa
isole
manufacturer bosa
designer sam baron
launched in 2013
2011 max included
3d_export
$11
Electric isolator 3D Model
...electric isolator 3d model
3dexport
electric equipment isolator station
electric isolator 3d model mindcraft 15061 3dexport
3d_export
$5
Sunflower flower plant isolated
...sunflower flower plant isolated
3dexport
sunflower plant isolated, 3d model
turbosquid
$30
Gas mask protection isolated
...gas mask protection isolated for download as ma, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1553330)
turbosquid
$24
Gas mask protection isolated
...gas mask protection isolated for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1577415)
turbosquid
$24
Mask helmet safety isolated
...sk helmet 3d safety isolated for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1581778)
turbosquid
$27
Gas mask protection futuristic isolated
...ask protection futuristic isolated for download as ma and fbx on turbosquid: 3d models for games, architecture, videos. (1562190)
turbosquid
$32
Gas mask protection isolated plastic
... protection isolated plastic for download as ma, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1545786)