Thingiverse
Glencairn carry case by roach118
by Thingiverse
Last crawled date: 2 years, 10 months ago
A case to carry:
6 Glencairn whisky glasses
measure
pen
small notebook
Based on the case designed here: https://www.thingiverse.com/thing:4852352
The front latch comes from: https://www.thingiverse.com/thing:4094861 (you will need these to complete the case)
Small overhang on the lid (notebook holder) will need supports, the rest should be ok without
Holes have been designed for M3 cap screws and M3 pressfit inserts.
Hardware required:
2 x 30mm M3 cap head screw (rear hinge)
4 x 25mm M3 cap head screw (front latch)
2 x 10mm M3 cap head screw (front handle)
8 M3 pressfit inserts - somewhat optional - will depend on how well the screws bite into the plastic. I found they were needed on the rear hinge but optional otherwise. Glues could be used to lock screws in place.
The notebook holder was designed around the Moleskine Cahier Pocket Ruled Notebook (or any notebook with approx size of 140x90x4)
Minor changes in v2:
less aggressive notebook holder (allows a bit more space)
better clearance for pressfit inserts
Printing time is long, ~3 days all up depending on infill/perimeter settings
NOTE: The dimensions the the Glencairn whisky glass vary from glass to glass. The case has only been tested on a small number of glasses (around 14) and all fit without issue However I'm sure that there are some glasses that will not fit. If you have concerns before printing the case, print the tester (you can print with zero infill). If your glasses fit in the tester, they should fit in the case (make sure the glass isnt sitting more than 4mm off the bottom of the tester)
6 Glencairn whisky glasses
measure
pen
small notebook
Based on the case designed here: https://www.thingiverse.com/thing:4852352
The front latch comes from: https://www.thingiverse.com/thing:4094861 (you will need these to complete the case)
Small overhang on the lid (notebook holder) will need supports, the rest should be ok without
Holes have been designed for M3 cap screws and M3 pressfit inserts.
Hardware required:
2 x 30mm M3 cap head screw (rear hinge)
4 x 25mm M3 cap head screw (front latch)
2 x 10mm M3 cap head screw (front handle)
8 M3 pressfit inserts - somewhat optional - will depend on how well the screws bite into the plastic. I found they were needed on the rear hinge but optional otherwise. Glues could be used to lock screws in place.
The notebook holder was designed around the Moleskine Cahier Pocket Ruled Notebook (or any notebook with approx size of 140x90x4)
Minor changes in v2:
less aggressive notebook holder (allows a bit more space)
better clearance for pressfit inserts
Printing time is long, ~3 days all up depending on infill/perimeter settings
NOTE: The dimensions the the Glencairn whisky glass vary from glass to glass. The case has only been tested on a small number of glasses (around 14) and all fit without issue However I'm sure that there are some glasses that will not fit. If you have concerns before printing the case, print the tester (you can print with zero infill). If your glasses fit in the tester, they should fit in the case (make sure the glass isnt sitting more than 4mm off the bottom of the tester)
Similar models
grabcad
free
GoPro Hero5 Session Case
....5 x 25 lg socket head cap screw as the hinge
use m3-.5 x 8 lg flat head screw as the latch
use m3-.5 hex nut for the latch screw
grabcad
free
The Glencairn Whisky Glass
...the glencairn whisky glass
grabcad
the glencairn whisky glass in stp and stl files
thingiverse
free
Glencairn transportting container / holder by brtekb
... the glass i glue a thin circle of leather on the bottom part where glass touches. this makes the glass to sit firm inside holder
thingiverse
free
Glencairn whisky tasting tags by Haxxlinus
...asting tags by haxxlinus
thingiverse
tags for the whisky glasses, intended for whisky tasting. suitable for the glencairn glass.
thingiverse
free
Blackberry Passport rugged carrying case by parice
...or an increased run time.
parts list:
6x m3-25mm cap head screws
6x m3 nuts
6x m3 washers
velcro
stick-on felt pads
leather cord
cults
free
Whisky Barrel for Glencairn-glass
...ansporting
the glass is fritting nicely i the barrel
new version of the "whisky_barrel_top" with a even better thread
grabcad
free
Glencairn (Whisky) Glass
...glencairn glass used for drinking whisky. unfortunately i couldn't make a render with whisky inside as i am new to rendering.
thingiverse
free
Case for Glencairn Glass by JustOrdinary
...y (small pieces of 3m stickers or eva foam) is recommended for even more protection but the plain printing one still does the job
thingiverse
free
Small case with hinge by PandaPrecision
...ould insert 2mm shaft into the hole of hinge.
fitting gap was set to 0.2mm.
sanding would be required when the fitting is tight.
thingiverse
free
Cooler Master MasterCase GPU Support Arm by WheresWaldo
...d two m5 nuts to hold it on from the back side.
stp 3d model file is included for those that want to remix to fit their own cases
Roach118
thingiverse
free
embroidery / cross stitch hoop by roach118
...e used or a nut and washer will also work. hole is sized for m3 bolt.
inner and outer hoop are printed together (gap is 0.75mm)
thingiverse
free
Glencairn "egg carton" by roach118
...t your glasses will fit, but this one is significantly less of an investment in time and material.
you can print with zero infill
thingiverse
free
Embroidery Hoop by josdeck
...outer hoop to hold the fabric better. i remixed roach118#39;s version (link below) to use an m5x25 bolt and...
Glencairn
3ddd
$1
Set with a pipe Peterson (Dublin)
...керамическая peterson -табакерка peterson -газета financial times - бокал glencairn (для односолодового виски) +виски стеки модификаторов открыты. можете менять...
thingiverse
free
Glencairn Rack by Magdel16
...glencairn rack by magdel16
thingiverse
a rack for holding glencairn glasses. just add wooden dowels.
thingiverse
free
Ardbeg Glencairn Lid by Urbex318
...eg glencairn lid by urbex318
thingiverse
this is a glencairn cap with the ardbeg logo on the top. happy sipping, all hail ardbeg
thingiverse
free
The Helm of Glencairn by 4MULE8
...scale the model up or down slightly to fit other glasses.
designed and modelled with blender, prepared and exported with 3ds max.
thingiverse
free
The Helm of Glencairn No Supports Remix
...
this is a remix of the helm of glencairn by 4mule8
i took out the supports, to make the model print better for resin printers.
thingiverse
free
Glencairn whisky tasting tags by Haxxlinus
...asting tags by haxxlinus
thingiverse
tags for the whisky glasses, intended for whisky tasting. suitable for the glencairn glass.
thingiverse
free
Glencairn whisky glass model by jockspice
...7 scale, but the model is designed at the full size of a mini glencairn. for a fullsize glass, increase the print scale to 1.35.
thingiverse
free
Case for Glencairn Glass by JustOrdinary
...y (small pieces of 3m stickers or eva foam) is recommended for even more protection but the plain printing one still does the job
thingiverse
free
The Glencairn Glass by b2vn
...er reason than i could :) i tried them out with some friends, and the whiskey seem to work equally well from the printed glasses.
thingiverse
free
Glencairn transportting container / holder by brtekb
... the glass i glue a thin circle of leather on the bottom part where glass touches. this makes the glass to sit firm inside holder
Carry
3ddd
$1
carry-on pouf
...carry-on pouf
3ddd
пуф
carry-on pouf, textures included
3ddd
$1
Carrie chair
... hickory chair
фабрика hickory , стул carrie chair! размеры: высота 890мм ширина 660мм глубина 710мм
design_connected
$11
Carry On stool
...carry on stool
designconnected
offecct carry on stool computer generated 3d model. designed by stenberg, mattias.
turbosquid
free
carry-on poufs
...
turbosquid
free 3d model carry-on poufs for download as max on turbosquid: 3d models for games, architecture, videos. (1209554)
turbosquid
$15
Carrying box
...squid
royalty free 3d model carrying box for download as ige on turbosquid: 3d models for games, architecture, videos. (1338653)
turbosquid
$5
Carry Pouf
...ty free 3d model carry pouf for download as max, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1637327)
turbosquid
$10
Gamma Carrie
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
design_connected
$11
Carrie LED Lantern
...carrie led lantern
designconnected
menu carrie led lantern computer generated 3d model. designed by norm architects.
turbosquid
free
Suzuki Carry Minivan
...rbosquid
free 3d model suzuki carry minivan for download as on turbosquid: 3d models for games, architecture, videos. (1377802)
turbosquid
$9
Carry black coin
...d
royalty free 3d model carry black coin for download as max on turbosquid: 3d models for games, architecture, videos. (1494700)
Case
3d_export
$1
case
...case
3dexport
case
archibase_planet
free
Case
...case
archibase planet
showcase show-case glass case
glass-case + cakes - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
showcase show-case glass case
glass-case for chips - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case shelving drawer
case - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case rack locker
case - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case drawer kitchen furniture
case - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case cupboard shelving
glass case - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case handbag suitcase
case - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case suitcase
case 5 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
locker case dresser
case - 3d model (*.gsm+*.3ds) for interior 3d visualization.