Thingiverse
Ghostbusters Pedal - Remix by ImperialWalker
by Thingiverse
Last crawled date: 3 years, 5 months ago
Countspatula's pedal is great, but there were some inaccuracies and missing details that I wanted to add into my trap.
Changes
Added side extension (small project box)
Removed CD logo (sorry Count) and cut out the middle as seen on the original
Added hole for Bullet Latch ( https://www.thingiverse.com/thing:4772769 )
Adjusted overall dimensions to closer resemble movie size
Added a bottom plate with "nubs" to fit the faucet washers
Added faux metal around front of trap
Adjusted position of hinge holes
Bottom Plate
I reduced the overall height of the pedal by 1/16" to give you some options. The bottom plate can be printed using PLA, or an aluminium plate can be attached.
In the movie, Faucet Washers were used as the pedal feet. Based on my research they should be 5/8" OD Bevelled Faucet (Bibb) Washers. These can be found at most hardware stores.
The screws are #4 3/8" Flat Wood screws. They should be Phillips head for accuracy.
Front Metal
On the screen used versions of the trap (which were made of wood), they had a 1/2" metal bar that wrapped around the front and sides.
On my trap I opted to use an aluminum bar, but a 3D printed version can also be used. The 3D printed version is pretty straight forward. Simply print it and finish it as you would your other parts.
If you opt for using real metal you can print and use the template provided for accurate hole placement. I opted to drill one hole, attach it to the pedal, bend it, then mark and drill the second set of holes. I continued this all the way around.
The reason for this is that I was unsure of how accurate the corner bends would be and if I had predrilled all the holes they may not have lined up of the corner radius was too tight or loose.
Bullet Latch
You can use a genuine K&V 903 Bullet latch if you can find one online, or you can print one as I did.
As getting one shipped to me was not an option I modelled (with the help of GBFans) a version which I think is pretty accurate. I then printed it in resin and slid it into place.
https://www.thingiverse.com/thing:4772769
Centre Cutout
On the original pedals, which were made of wood, the centre piece was left as a hole with the metal bottom covering it up.
On the GB1 trap a resistor (same as on the side of the trap) can be seen, which the yellow tube connect to. I am unable to find what was done for the GB2 pedal, but I opted to go with the GB1 design.
I first resin printed the resistor in CountSpatula's files. In my files you'll find ( GB-Pedal-ElectronicsTemplate.stl ). I used this to mark and cut out a thin sheet of plastic card where I could attach the resistor (and other greeblies).
This isn't necessary and you can simply glue yours in, but I wanted some flexibility and it saves me having to sand inside.
Final Thoughts
These changes were made based on my research and from the help of GBFans. However, there may still be inaccuracies that I have not caught.
I opted to print this with a fairly high infill (85%) as I wanted it to be strong and have some weight to it. I also printed it with supports, but with the "Touching build plate only" settings as I didn't want the internal holes to be filled.
Let me know if there are any issues and have fun!
Changes
Added side extension (small project box)
Removed CD logo (sorry Count) and cut out the middle as seen on the original
Added hole for Bullet Latch ( https://www.thingiverse.com/thing:4772769 )
Adjusted overall dimensions to closer resemble movie size
Added a bottom plate with "nubs" to fit the faucet washers
Added faux metal around front of trap
Adjusted position of hinge holes
Bottom Plate
I reduced the overall height of the pedal by 1/16" to give you some options. The bottom plate can be printed using PLA, or an aluminium plate can be attached.
In the movie, Faucet Washers were used as the pedal feet. Based on my research they should be 5/8" OD Bevelled Faucet (Bibb) Washers. These can be found at most hardware stores.
The screws are #4 3/8" Flat Wood screws. They should be Phillips head for accuracy.
Front Metal
On the screen used versions of the trap (which were made of wood), they had a 1/2" metal bar that wrapped around the front and sides.
On my trap I opted to use an aluminum bar, but a 3D printed version can also be used. The 3D printed version is pretty straight forward. Simply print it and finish it as you would your other parts.
If you opt for using real metal you can print and use the template provided for accurate hole placement. I opted to drill one hole, attach it to the pedal, bend it, then mark and drill the second set of holes. I continued this all the way around.
The reason for this is that I was unsure of how accurate the corner bends would be and if I had predrilled all the holes they may not have lined up of the corner radius was too tight or loose.
Bullet Latch
You can use a genuine K&V 903 Bullet latch if you can find one online, or you can print one as I did.
As getting one shipped to me was not an option I modelled (with the help of GBFans) a version which I think is pretty accurate. I then printed it in resin and slid it into place.
https://www.thingiverse.com/thing:4772769
Centre Cutout
On the original pedals, which were made of wood, the centre piece was left as a hole with the metal bottom covering it up.
On the GB1 trap a resistor (same as on the side of the trap) can be seen, which the yellow tube connect to. I am unable to find what was done for the GB2 pedal, but I opted to go with the GB1 design.
I first resin printed the resistor in CountSpatula's files. In my files you'll find ( GB-Pedal-ElectronicsTemplate.stl ). I used this to mark and cut out a thin sheet of plastic card where I could attach the resistor (and other greeblies).
This isn't necessary and you can simply glue yours in, but I wanted some flexibility and it saves me having to sand inside.
Final Thoughts
These changes were made based on my research and from the help of GBFans. However, there may still be inaccuracies that I have not caught.
I opted to print this with a fairly high infill (85%) as I wanted it to be strong and have some weight to it. I also printed it with supports, but with the "Touching build plate only" settings as I didn't want the internal holes to be filled.
Let me know if there are any issues and have fun!
Similar models
thingiverse
free
Ghostbusters Trap Pedal - K&V 903 Bullet Latch by ImperialWalker
...nted flat.
head over to countspatula's page for more ghostbusters trap downloads.
https://www.thingiverse.com/thing:1394639
thingiverse
free
Ghostbusters Ghost Trap (1984) by countspatula
...d out by using the 3d printed ones as a template.
to learn more about how the trap was designed and built, see me on tested.com:
thingiverse
free
Ghostbusters Ghost Trap Knob GB1 1984 Heathkit
...he knob was too small for the post. i have corrected it, but it is a tight fit. i would recommend sanding down the post slightly.
thingiverse
free
Ghostbusters Spirit Halloween Ghost Trap Upgrades by WindDrake
...pdate 9/9/2018 - updated bearing axle to r2 - slight dimensional changes to better fit all traps due to manufacturing tolerances.
thingiverse
free
Mostly Printed CNC Optical End Stop Mount for Z Axis by towa
...this version as z stop mount.
you can put a m8 washer between "middle end" and the plate to achieve a better alignment.
thingiverse
free
Proton Pack L-Bracket (GB1 & GB2) by Jimsy33
...;m gonna do. i made four version gb1 and 2 without holes, and the same models with holes.
link to gbfans: https://www.gbfans.com/
thingiverse
free
Latch with pin lock prototype by siderits
...of the latch to fit your needs.
good luck!
3d model: truespace
printer: form1+, resin version 2
time from art to part: 30 min
thingiverse
free
Mendel y-bar-clamp_10off remake in OpenSCAD w nut traps by josefprusa
...e of the plain type so that a washer and bolt rest properly on them.
updated:
bigger holes, you should not have to drill them out
thingiverse
free
Bathroom sink drain hair trap
...s in the pictures.
supports: if you print it upside-down you need less support material compared to printed in mounting position.
thingiverse
free
Guitar Pedal Effect Holder by Simmons
...bottom.
you just need 4 screw to hold it.
the screw i used is 1,5 cm width but you can use whatever you want that fit your needs.
Imperialwalker
thingiverse
free
Star Trek: TNG - Tensegrity Table by ImperialWalker
... dabble in 3d modelling, so hopefully it works well for everyone. let me know if you have any issues and i'll try and fix it.
thingiverse
free
Ghostbusters Trap Pedal - K&V 903 Bullet Latch by ImperialWalker
...nted flat.
head over to countspatula's page for more ghostbusters trap downloads.
https://www.thingiverse.com/thing:1394639
thingiverse
free
Funnel Insert by ImperialWalker
...he excess mesh around the outside.
you should now have a nice little insert that you can place or glue into your printed funnel.
Ghostbusters
3d_ocean
$89
Cadillac Miller-Meteor Ghostbusters Ectomobile
...y, in real units of measurement, qualitatively and maximally close to the original. model formats: - *.max (3ds max 2008 scanl...
cg_studio
$99
Cadillac ECTO-1 Ghostbusters 19593d model
...fbx .lwo .max .obj - cadillac ecto-1 ghostbusters 1959 3d model, royalty free license available, instant download after purchase.
3d_export
$129
Cadillac Miller Meteor Ghostbusters Ectomobile 3D Model
...llac miller meteor ghostbusters ectomobile 3d model download .c4d .max .obj .fbx .ma .lwo .3ds .3dm .stl humster3d 65046 3dexport
cg_studio
$99
Cadillac Miller-Meteor Ghostbusters Ectomobile3d model
... .obj - cadillac miller-meteor ghostbusters ectomobile 3d model, royalty free license available, instant download after purchase.
3d_ocean
$19
Fire Station Building Low Poly
...building busters city department exterior fire fireman flat ghost ghostbusters house low poly model red rescue station structure team...
humster3d
$75
3D model of Cadillac Miller-Meteor Ghostbusters Ectomobile
...ac miller-meteor ghostbusters ectomobile in various file formats. all our 3d models were created maximally close to the original.
3d_export
$99
Cadillac ECTO1 Ghostbusters 1959 3D Model
...ring 1959 movie famous ghost ecto-1 ghostbusters busters emergency
cadillac ecto1 ghostbusters 1959 3d model squir 86957 3dexport
3d_export
$25
pke meter ghostbusters
...ource of the energy,<br>the wings will extend to their fullest length and the meter will buzz noticeably at a higher pitch.
3d_export
$25
ecto goggles ghostbusters
...es.<br>after the goggles were damaged during the ny shooting, warning labels were put on the lenses for aesthetic purposes.
3d_export
$25
ghost trap ghostbusters
...t when a captured ghost is put into the containment unit, the entity is pumped out of the trap cartridge so it can be used again.
Pedal
design_connected
$11
Pedal Bin and Toilet Brush
...l bin and toilet brush
designconnected
menu pedal bin and toilet brush computer generated 3d model. designed by norm architects.
3d_export
$49
Old bicycle 3D Model
...bicycle bike classic classical wheel drive ride vehicle transport pedal saddle seat cycling vintage road antique people sport handlebars...
cg_studio
$47
Mountain Bike MTB3d model
...off-road extreme vehicle transport wheel mtb dirt frame seat pedal spokes rim brake .obj .fbx .max .3ds - mountain...
3d_ocean
$49
Mountain Bike MTB
...mtb 3docean bicycle brake dirt extreme frame mtb off-road pedal rim rock seat spokes sport transport vehicle wheel ultra...
3d_ocean
$7
Kids pedal car
...kids pedal car
3docean
car kids pedal red toy yellow
kids yellow and red pedal car
3d_ocean
$19
Bicycle
...3docean bicycle bike car drive extreme fast jump mountain pedal sport tire vehicule complete old school bicycle, the zip...
3d_ocean
$40
Boss Guitar Effect Collection
...render with 3ds max 7 boss rv5 digital reverb pedal polygons 4267 vertices 2317 boss ge7 7-band graphic equalizer...
3d_ocean
$59
Racing Bike Model: Bianchi Oltre XR2
...carbon chain chrome cogwheel cycling derailleur frame gear metal pedal racingbike saddle spokes sport tires tourdefrance vehicle velo wheels...
3d_ocean
$39
Stylish Bike 3D Model
...equipment exercise frame hobbies mountain mtb off-road orange parts pedal rim seat simulator spokes sport sports steering stylish transport...
3d_export
$56
Mountain Bike MTB 3D Model
...off-road extreme vehicle transport wheel mtb dirt frame seat pedal spokes rim brake mountain bike mtb 3d model kreatura...
Remix
3ddd
$1
Barovier&Toso / Manhattan Remix 7192
... 004293-142405
в коллекции есть люстры 7, 9, 12 рожковые. диаметр соответственный 1000, 1250, 1500 мм.
3d_ocean
$5
Vray fabric Kvadrat remix green - tileable
...th vray and 3dsmax. high-resolution texture images (2000×2000 px) file included: shader vray 2.40 texture image 3ds max 2011 file
3ddd
$1
Muuto fiber chair
...grey/grey, dusty green/dusty green, nature/oak, natural white/oak upholstery options remix 183/black, remix 133/grey, remix 643/dusty red leather options black...
cg_studio
$49
HTC One Mini 2 Gunmetal Gray3d model
...cell phone mobile cellular super lcd touchscreen touch screen remix gunmetal grey silver .max .obj .mb .lwo .fbx .c4d...
cg_studio
$49
HTC One Mini 2 Glacial Silver3d model
...cell phone mobile cellular super lcd touchscreen touch screen remix glacial silver gray .max .obj .mb .lwo .fbx .c4d...
cg_studio
$49
HTC One Mini 2 Amber Gold3d model
...cell phone mobile cellular super lcd touchscreen touch screen remix amber gold .max .obj .mb .lwo .fbx .c4d .3ds...
3ddd
$1
Barovier&Toso 7190-7195
...7190-7195 3ddd barovier&toso потолочнай люстра фабрики barovier&toso;, коллекция manhattan remix артикул 7190-7195. размеры в inches: 39"...
3d_export
$5
3D Locking Handle Weatherproof Storage Box Container
...handle weatherproof storage box container 3dexport new, improved and remixd! no screws required. print-in-place. weatherproof. parametric. 2 parts. easy...
3d_export
$10
multicolored remix parametric table furniture
... fbx, obj, mtl, archive with textures. the model has no glitches. render and materials - vray . without using plugins. good use!
3d_export
$12
remix yamaha rm1x
...remix yamaha rm1x
3dexport
geometry triangles 15.2k vertices 7.6k pbr no textures 1 materials 1 uv layers yes