Cults
Geartar
by Cults
Last crawled date: 6 years, 2 months ago
UPDATE 1: I have added a little video here for you to see all the gears moving:
https://youtu.be/DH4wXGN3lu0
I have here my 3D printed guitar.
follow me on instagram (you will see videos of the guitar in action dont forget to like it there!)
hugo archicad
I have zero music knowledge.
My friend Steve has a band called 44 inch chest and he saw the guitar on YouTube that was 3D printed and jokingly asked me to make one just like it for him.
I said I would need a donor guitar first so one day he got one at a flea market.
Then it sat in my wardrobe for about 6 months until one day I couldn't think of what to 3D print next so I started.
In terms of parts I used the donor guitar, pulled it all apart then I photocopied it and started modeling.
I had to reduce the body by 97% to get it to fit on my cr-10 because it did say it had a 300x300x400 high but the reality was a little smaller.
I did not shrink anything else only the body.
So I used the gears from a thingiverse post that someone else had made already.
I did not shrink anything else.
Because of the 97% I had to cut away a little of the wooden handle thing because it would not slot perfectly because although it was modeled to fit I couldn't fit it on the printer bed.
List of things you need to make this guitar:
- about 2 kilos of pla
-1 mini servo motor which I had to open to make sure it would do full rotation( I found the answer on YouTube)
-1 EL wire (1 meter)(red) with its electronic part.
-1 battery holder (2xaa) for the servo
-glue (clear for the EL wire)
-glue to stick the main guitar pieces, the bottom lid has a groove on its top for the glue to go on so it doesnt lift the lid too much with the thickness of the glue blob
-wire to add length to the componets and that tube thing that you put on the wires that shrinks when you put it under heat or cigar lighter (I dont know the name but better than using electrical tape looks so professional with it and all the soldering stays put)
I wanted to fit the servo motor battery inside the guitar, I left a space there but I couldn't at the end because I couldn't get the EL wire to work without its little box ( there is some electronic stuff in it that I couldn't get out of the box so it sits outside.
I would like to find a way to fit it inside (my electronic know how is not the best)
I did managed to solder all the connections and connect a switch (a key that turns the servo on).
I designed everything to conceal the wiring and made hidden little tunnels to run the wiring, and also made a little channel to run the EL wire through cleanly.
I don't know if my donor guitar is like other guitars so the design I have made works for this guitar but don't know if it would work on others.
Nu supports needed at all anywhere.
A nice big 3D printer would be nice but nothing stopping anyone from cutting it up in pieces.
If you do end up cutting it in pieces do not shrink anything then everything will work perfectly.
Enjoy
I know i did designing it and putting it together.
Also when putting screws i learned that if you put your soldering iron on top of the screw for a bit and hold it there, the heat transfers to the plastic making it easier to screw then when its cooled its stick super well.
One thing...the gears are not my design, i got them from here:
https://www.thingiverse.com/thing:2218127
And have added them here so you can download everything you need from one place.
https://youtu.be/DH4wXGN3lu0
I have here my 3D printed guitar.
follow me on instagram (you will see videos of the guitar in action dont forget to like it there!)
hugo archicad
I have zero music knowledge.
My friend Steve has a band called 44 inch chest and he saw the guitar on YouTube that was 3D printed and jokingly asked me to make one just like it for him.
I said I would need a donor guitar first so one day he got one at a flea market.
Then it sat in my wardrobe for about 6 months until one day I couldn't think of what to 3D print next so I started.
In terms of parts I used the donor guitar, pulled it all apart then I photocopied it and started modeling.
I had to reduce the body by 97% to get it to fit on my cr-10 because it did say it had a 300x300x400 high but the reality was a little smaller.
I did not shrink anything else only the body.
So I used the gears from a thingiverse post that someone else had made already.
I did not shrink anything else.
Because of the 97% I had to cut away a little of the wooden handle thing because it would not slot perfectly because although it was modeled to fit I couldn't fit it on the printer bed.
List of things you need to make this guitar:
- about 2 kilos of pla
-1 mini servo motor which I had to open to make sure it would do full rotation( I found the answer on YouTube)
-1 EL wire (1 meter)(red) with its electronic part.
-1 battery holder (2xaa) for the servo
-glue (clear for the EL wire)
-glue to stick the main guitar pieces, the bottom lid has a groove on its top for the glue to go on so it doesnt lift the lid too much with the thickness of the glue blob
-wire to add length to the componets and that tube thing that you put on the wires that shrinks when you put it under heat or cigar lighter (I dont know the name but better than using electrical tape looks so professional with it and all the soldering stays put)
I wanted to fit the servo motor battery inside the guitar, I left a space there but I couldn't at the end because I couldn't get the EL wire to work without its little box ( there is some electronic stuff in it that I couldn't get out of the box so it sits outside.
I would like to find a way to fit it inside (my electronic know how is not the best)
I did managed to solder all the connections and connect a switch (a key that turns the servo on).
I designed everything to conceal the wiring and made hidden little tunnels to run the wiring, and also made a little channel to run the EL wire through cleanly.
I don't know if my donor guitar is like other guitars so the design I have made works for this guitar but don't know if it would work on others.
Nu supports needed at all anywhere.
A nice big 3D printer would be nice but nothing stopping anyone from cutting it up in pieces.
If you do end up cutting it in pieces do not shrink anything then everything will work perfectly.
Enjoy
I know i did designing it and putting it together.
Also when putting screws i learned that if you put your soldering iron on top of the screw for a bit and hold it there, the heat transfers to the plastic making it easier to screw then when its cooled its stick super well.
One thing...the gears are not my design, i got them from here:
https://www.thingiverse.com/thing:2218127
And have added them here so you can download everything you need from one place.
Similar models
cults
free
Servo Flower
...small wood screws (or the ones that come with the sg90 servos).
printed in pet-g
if you have any questions feel free to ask :-)
cults
free
Mini can carrier
...e one more project to 3d print and i am sure you do too
so put supports on to the buildplate, nothing else needs support.
enjoy
cults
free
Sir PIgglesby Right Flower Belt V2 (Untested)
...a project.
again, this is untested. which is why it has been posted as separate from the main project.
all feedback encouraged.
cults
$1
Little Cactus
...version that comes with a little sandy base or one without. both of them are stable so you can easily put it on a table or shelf.
cults
$1
Spinner 4 Bearing
...may need to shave off a bit in the circles because the plastic does shrink so be prepared to shaved of a bit for the perfect fit.
cults
free
Taco Train
... available, but i wouldn't recommend that as it isn't non-toxic. pla would be better or even better the fda approved pla.
cults
free
Cat Proofing Cups (88mm)
...nk or enlarge it to fit your cups.
!don't forget to check out my other designs and follow my daily kookoo uploads, enjoy ;)
cults
free
Deathstroke Mask with two eyes
...y
this mask was sized to fit an adult male but but do size accordingly.
i will not make one with three eyes so don't ask :)
cults
free
Wireless Button Presser
...penings). screw the raspberry pi onto the bottom with four screws. after ensuring that everything works, screw on the lid. done!
cults
free
Yoda Bust Hi Res 56mb
...they'll get caught out one day :)
p.s yes i fixed his eyes after the photos were taken :) the pinholes were creeping me out.
Instrument
cults
$18
Instrument with strings
... music rope guitar custom kit
instrument de musique à 4 cordes pensé et créé par moi , en kit , pour la plupart des imprimantes .
cults
free
Jinghu (Chinese Bowed Instrument)
...jinghu (chinese bowed instrument)
cults
jinghu (chinese bowed instrument)
jinghu (chinese bowed instrument)
cults
free
Balalaika (Russian Stringed Instrument)
...balalaika (russian stringed instrument)
cults
balalaika (russian stringed instrument)
balalaika (russian stringed instrument)
cults
free
Recorder (Music instrument)
...recorder (music instrument)
cults
a fully 3d printable instument
cults
free
3D Printed One Man Band Musical Instrument
...be.com/watch?v=_yq-dfcyeas
one man band how to assemble: https://www.youtube.com/watch?v=2v9czutdlus
thank you for your support!
cults
free
Loosen ropes
...to loosen or tighten the strings of a string instrument ...
cults
$6
ukulele
...ukulele cults ukulele instrument guitar toy 3d printable...
cults
free
Chromatic Panflute
...chromatic panflute cults flute recorder instrument panflute chromatic a chromatic tenor panflute from c3 to...
cults
free
Shamisen Tuning Peg
...shamisen tuning peg cults accessory instrument music peg shamisen string tool tuning tuning peg for...
cults
$1
Arm Mini Cooper
...for gps or tel, which adapts to countryman minicopper instrument all models until...
Guitar
cults
free
Guitar Hero Guitar Hook
...guitar hero guitar hook
cults
wall hook for your gaming guitar.
cults
$2
Support guitare
...support guitare
cults
support guitare
support guitare
cults
free
guitar lamp
...guitar lamp
cults
guitar lamp
guitar lamp
cults
$1
Guitar with base
...guitar with base
cults
guitar electrical
electric guitar with rock and roll legend, to use as an ornament or paperweight.
cults
free
PRS Guitar
...prs guitar
cults
gadget guitar keychains prs fashion
keyring made on a prs guitar model.
cults
free
Acoustic guitar
...ic guitar guitar
assembly instruction in a assembly.pdf file
sound https://drive.google.com/open?id=0b0-nmpdd8tg7yzjqq0wtnvjiwgm
cults
free
Аcoustic guitar
...ic guitar guitar
assembly instruction in a assembly.pdf file
sound https://drive.google.com/open?id=0b0-nmpdd8tg7u1mtdgvez2pgyuk
cults
free
Rickenbacker Bass Guitar
...offer or to please.
she is on a scale compared to my other guitars.
100 mm for electric guitars.
120 mm for the bass guitar
cults
free
Guitar Pick
...arpick rock
this is a simple guitar pick which almost works like a "real" one. have fun when making some music with it!
cults
$3
Johnny Hallyday Guitar
...ay guitar
cults
johnny hallyday 3d johnny hallyday logo guitar guitar jh
johnny hallyday 3d guitar for all johnny fans like me =)
Musical
cults
free
Musical Orrery
...musical orrery
cults
musical orrery
musical orrery
cults
free
Fairy Music Box
...fairy music box
cults
fairy music box
fairy music box
cults
free
Materialize─PottedMaterialize─Music Maker
...terialize─pottedmaterialize─music maker
cults
materialize─pottedmaterialize─music maker
materialize─pottedmaterialize─music maker
cults
free
Music Trumpet
...ces !!!!
the mouthpiece is also available as a printable file. but i had a little more work to design a form that works well ...
cults
free
Recorder (Music instrument)
...recorder (music instrument)
cults
a fully 3d printable instument
cults
free
zZcube's Music Box (Tune Box)
...zzcube's music box (tune box)
cults
zzcube's music box (tune box)
zzcube's music box (tune box)
cults
$3
Piano Hole Punch Music Box
...punch since i could not find models for these musical boxes, i dedicated myself to designing a custom one....
cults
free
3D Printed One Man Band Musical Instrument
...be.com/watch?v=_yq-dfcyeas
one man band how to assemble: https://www.youtube.com/watch?v=2v9czutdlus
thank you for your support!
cults
free
3d drums, 3d rock drums, 3d intrument, 3d music, 3d printable intrument
...ent, 3d music, 3d printable intrument
cults
intruments objects
this 3d model was modeled at detail, making similar to real drums.
cults
$1
Bandstand
... of langres.
music kiosk, ho scale inspired by that of the city of langres (france)
to find on http://amigagoma.free.fr
Electric
cults
free
turbocharger with electric motor
...turbocharger with electric motor
cults
turbocharger with electric motor
turbocharger with electric motor
cults
free
Electrical Connection Box
...electrical connection box
cults
electrical connection box
electrical connection box
cults
$5
Propeller Electric motor
...propeller electric motor
cults
propeller engine electric
propeller electric motor ø130 / ø14 / 22mm
cults
$5
Propeller Electric motor
...propeller electric motor
cults
propeller engine electric
propeller electric motor ø130 / ø14 / 32mm
cults
$1
Electric guitar with base
...ric guitar with base
cults
guitar electrical
electric guitar with rock and pop legend, can be used as an ornament or paperweight.
cults
$1
Electric motor mount
...electric motor mount
cults
avionrc rc batis engine electric 380-400
type 380-400 electric aircraft engine mount
cults
$1
electric toothbrush holder
...electric toothbrush holder
cults
brush at teeth
support for 2 electric toothbrushes and associated tips
cults
free
GELFEED glue electric feeder
...gelfeed glue electric feeder
cults
gelfeed glue electric feeder
gelfeed glue electric feeder
cults
$2
Electrical protection on Anet8
...electrical protection on anet8
cults
for 3d printer anet8
electrical protection consisting of a sheath and support switch
cults
$1
Electrical conductivity support
...cults
material conductivity support
small support that allows to make tests of electrical conductivity of a material for example.