Thingiverse
Gearbox 256 / Getriebe 256 by CONSTRUCTeR
by Thingiverse
Last crawled date: 3 years ago
Gearbox 256 /
Getriebe 256
I used the parts from "Gearset 1:2 ratio" to build a gearbox, but instead of designing a reduction system, i wanted to go a different way and increase the outgoing speed.
The idea was to create a hand driven box for various tasks which require fast rotation. It's also a test of how much you can increase the speed with 3D-printed gears.
As the rotation speed goes up, accuracy and friction become more important. In the attached video, the crank is rotated at 10 rpm while the driven shaft spins at 2,560 rpm.
In conclusion, the crank rotation needs a bit too much force. I've just started designing a complete new gearbox for easier usage.
/
Ich habe die Teile aus "Zahnradsatz 1:2 Übersetzung" verwendet um ein Getriebe zu bauen, aber anstatt ein Reduktionssystem zu konstruieren, wollte ich einen anderen Weg gehen
und die Ausgangsgeschwindigkeit erhöhen. Die Idee war, ein handbetriebenes Getriebe für verschiedene Aufgaben zu entwickeln, die eine schnelle Rotation benötigen.
Es ist auch ein Test wie hoch man die Geschwindigkeit mit zu 3D-gedruckten Zahnrädern erhöhen kann. Bei steigender Drehgeschwindigkeit werden Genauigkeit und Reibung immer
wichtiger. In dem angehängten Video wird die Kurbel mit etwa 10 u/min gedreht, während die angetriebene Welle mit 2.560 U/min rotiert. Zusammenfassend benötigt die Kurbel-Drehung
etwas zu viel Kraft. Ich habe gerade begonnen, ein komplett neues Getriebe für eine einfachere Nutzung zu entwickeln.
Parts/Teile
Box/Gehäuse - 1 Piece/Stück
182 x 63,7 x 80 mm
Insert in pockets/In Taschen einsetzen:
2x Bearing/Lager 608 Z (7x8x22mm)
2x Bearing/Lager 6901 Z (6x12x24mm)
10x Nut/Mutter M5
1x Part/Teil 8 - Bearing-disk/Lagerscheibe 1
1x Part/Teil 19 - Bearing-disk/Lagerscheibe 2
Top / Deckel - 1 Piece/Stück
182 x 65,5 x 4 mm
Includes holes for 3.5 mm screws, but the top fits perfectly without them. / Enthält Bohrungen für 3,5 mm Schrauben, aber der Deckel hält auch ohne sehr gut.
Shaft / Welle 1 - 1 Piece/Stück
12 x 50 mm
Part order / Reihenfolge der Teile
a - Part/Teil 6 - Crank/Kurbel
b - Part/Teil 7 - Spacer/Distanzstück 1
c - Part/Teil 8 - Bearing-disk/Lagerscheibe 1
d - Bearing/Lager 61901 ZZ (6x12x24mm)
e - Part/Teil 9 - Clamp/Klemme 1
f - Part/Teil 10 - Spur gear/Stirnrad 1
g - Part/Teil 11 - Spacer/Distanzstück 2
h - Bearing/Lager 61901 ZZ (6x12x24mm)
The gear is rigidly connected to the shaft and spins with the crank rotation.
This shaft transmits the biggest torque. Both parts must be printed more durable
(4 perimeter, 4 solid top/bottom layers, infill 40%). The crank is glued to the outer
end of the shaft.
/
Das Zahnrad ist starr mit der Welle verbunden und rotiert mit der Kurbeldrehung.
Diese Welle überträgt das größte Drehmoment. Beide Teile müssen stabil gedruckt werden
(4 Umrissbahnen, 4 Volle Boden- und Dachschichten, Füllung 40%). Die Kurbel ist mit dem
äußeren Wellenende verklebt.
Shaft / Welle 2 - 2 Piece/Stück
8 x 54 mm
Part order "shaft 4 gears" / Reihenfolge der Teile "Welle mit 4 Zahnrädern"
a - Part/Teil 12 Spacer/Distanzstück 3
b - Assembly Doublegear without Part/Teil 18 Spacer/Distanzstück 7
c - Assembly Doublegear
d - Assembly Doublegear
e - Assembly Doublegear
f - Part/Teil 13 - Spacer/Distanzstück 4
g - Part/Teil 14 - Clamp/Klemme 2
Part order "shaft 3 gears" / Reihenfolge der Teile "Welle mit 3 Zahnrädern"
a - Part/Teil 15 Spacer/Distanzstück 5
b - Assembly Doublegear without Part/Teil 18 Spacer/Distanzstück 7
b - Assembly Doublegear
c - Assembly Doublegear
a - Part/Teil 16 - Spacer/Distanzstück 6
e - Part/Teil 14 - Clamp/Klemme 2
Assembly Doublegear - 7 Piece/Stück
a - Part/Teil 17 - Double spur gear / Doppelstirnrad
b - Bearing/Lager 608Z (7x8x22mm)
c - Part/Teil 18 - Spacer/Distanzstück 7
The gears are spinning freely on the shafts and transmit the torque.
The shafts can be printed with standard settings.
/
Die Zahnräder drehen frei auf den Wellen und übertragen das Drehmoment.
Die Wellen können mit Standardeinstellungen gedruckt werden.
Shaft 3 / Welle 3 - 1 Piece/Stück
8 x 62 mm
Part order / Reihenfolge der Teile
a - Part/Teil 19 - Bearing-disk/Lagerscheibe 2
b - Bearing/Lager 608Z (7x8x22mm) outside/außen
c - Part/Teil 20 - Spur gear/Stirnrad 2
d - Part/Teil 14 - Clamp/Klemme 2
e - Bearing/Lager 608Z (7x8x22mm) inside/innen
Crank/Kurbel - 1 Piece/Stück
181 x 34 x 10 mm
Part order / Reihenfolge der Teile
a - Bearing/Lager 61901 ZZ (6x12x24mm)
b - Part/Teil 21 - Spacer handle bearing/Scheibe Grifflager
c - Part/Teil 22 - Handle/Griff
d - Part/Teil 9 - Clamp/Klemme 1
e - Part/Teil 9 - Clamp/Klemme 1
f - Part/Teil 9 - Clamp/Klemme 1
g - Part/Teil 9 - Clamp/Klemme 1
f - Part/Teil 9 - Clamp/Klemme 1
The crank and the handle transmit a high bending moment. Both parts must be printed more durable
(3 perimeter, 3 solid top/bottom layers, infill 30%). The "spacer handle bearing" is glued.
/
Die Kurbel und der Griff übertragen ein hohes Biegemoment. Beide Teile müssen stabil gedruckt werden
(3 Umrissbahnen, 3 Volle Boden- und Dachschichten, Füllung 30%). Die "Scheibe am Grifflager" ist eingeklebt.
Spacer/Distanzstück 1 - 1 Piece/Stück
6.4 x 16 x 12 mm
Bearing-disk/Lagerscheibe 1 - 1 Piece/Stück
1 x 32 x 18 mm
Clamp/Klemme 1 - 6 Piece/Stück
10 x 20 x 12 mm
Spur gear/Stirnrad 1 - 1 Piece/Stück
Number of teeth / Zähnezahl: 30
Pitch circle / Wälzkreisdurchmesser: 67.5 mm
Hub diameter / Nabendurchmesser: 12 mm
Spacer/Distanzstück 2 - 1 Piece/Stück
2 x 16 x 12 mm
Spacer/Distanzstück 3 - 1 Piece/Stück
1,5 x 12 x 8 mm
Spacer/Distanzstück 4 - 1 Piece/Stück
2,25 x 12 x 8 mm
Clamp/Klemme 2 - 3 Piece/Stück
10 x 16 x 8 mm
Spacer/Distanzstück 5 - 1 Piece/Stück
6 x 12 x 8 mm
Spacer/Distanzstück 6 - 1 Piece/Stück
6,75 x 12 x 8 mm
Double spur gear / Doppelstirnrad - 7 Piece/Stück
Number of teeth / Zähnezahl: 15 and 30
Pitch circle / Wälzkreisdurchmesser: 33.75 and 67.5 mm
Hub diameter / Nabendurchmesser: 22 mm
Spacer/Distanzstück 7 - 5 Piece/Stück
2 x 12 x 8 mm
Bearing-disk/Lagerscheibe 2 - 1 Piece/Stück
1 x 29 x 18 mm
Spur gear/Stirnrad 2 - 1 Piece/Stück
Number of teeth/Zähnezahl: 15
Pitch circle/Wälzkreisdurchmesser: 33.75 mm
Hub diameter/Nabendurchmesser: 8 mm
Spacer handle bearing/Scheibe Grifflager - 1 Piece/Stück
2 x 29,5 x 21 mm
Handle/Griff - 1 Piece/Stück
12 x 58 mm
In order for the gears to work well together, the 3D printer should be
calibrated properly and produce clean external surfaces. If possible
aline the starting points of the outer perimeters and
remove the plastic bumps in a single cut.
The shafts are constructed without play. If the parts are not
plug into each other, STL files must be downsized in the radial direction.
Some parts includes a clamping function with nuts and grub screws. I noticed during the assembly,
that the clamping can be implemented easier by variation of the parts dimensions.
After the assembly the gearbox might need some running time till the gears are working smoothly. Lubrication is very helpful.
/
Damit die Zahnräder gut miteinander arbeiten sollte der 3D-Drucker korrekt
kalibriert sein und saubere Außenflächen produzieren. Nach Möglichkeit setzt
man den Startpunkt der äußeren Bahnen übereinander um die dortige
Kunststoffanhäufung mit einem Schnitt entfernen zu können.
Die Wellen sind ohne Spiel konstruiert. Falls sich die Teile nicht
ineinander stecken lassen, müssen STL-Dateien in radialer Richtung
verkleinert werden.
Bei einige Teile ist eine Klemmfunktion mit Muttern und Madenschrauben vorgesehen. Ich habe während der Montage bemerkt,
dass die Klemmung durch Variation der Teileabmessungen einfacher zu realisieren ist.
Nach der Montage benötigt das
Getriebe einige Zeit, bis die Zahnräder reibungslos funktionieren. Schmierung ist sehr hilfreich.
Printparameter / Druckparameter
Printer / Drucker: Velleman K8200
Material: PLA
Temp. Extruder: 190 °C
Temp. Bed / Bett: 50 °C
Layerheight / Schichthöhe: 0.25 mm
Perimeters / Umrissbahnen: 2 - 4
Solid Top Bottom Layer / Volle Boden- und Dachschichten: 2
Infill / Fülldichte: 40 %
No Support needed / keine Stützkonstruktion nötig
https://www.youtube.com/watch?v=84odyuiceQc
Getriebe 256
I used the parts from "Gearset 1:2 ratio" to build a gearbox, but instead of designing a reduction system, i wanted to go a different way and increase the outgoing speed.
The idea was to create a hand driven box for various tasks which require fast rotation. It's also a test of how much you can increase the speed with 3D-printed gears.
As the rotation speed goes up, accuracy and friction become more important. In the attached video, the crank is rotated at 10 rpm while the driven shaft spins at 2,560 rpm.
In conclusion, the crank rotation needs a bit too much force. I've just started designing a complete new gearbox for easier usage.
/
Ich habe die Teile aus "Zahnradsatz 1:2 Übersetzung" verwendet um ein Getriebe zu bauen, aber anstatt ein Reduktionssystem zu konstruieren, wollte ich einen anderen Weg gehen
und die Ausgangsgeschwindigkeit erhöhen. Die Idee war, ein handbetriebenes Getriebe für verschiedene Aufgaben zu entwickeln, die eine schnelle Rotation benötigen.
Es ist auch ein Test wie hoch man die Geschwindigkeit mit zu 3D-gedruckten Zahnrädern erhöhen kann. Bei steigender Drehgeschwindigkeit werden Genauigkeit und Reibung immer
wichtiger. In dem angehängten Video wird die Kurbel mit etwa 10 u/min gedreht, während die angetriebene Welle mit 2.560 U/min rotiert. Zusammenfassend benötigt die Kurbel-Drehung
etwas zu viel Kraft. Ich habe gerade begonnen, ein komplett neues Getriebe für eine einfachere Nutzung zu entwickeln.
Parts/Teile
Box/Gehäuse - 1 Piece/Stück
182 x 63,7 x 80 mm
Insert in pockets/In Taschen einsetzen:
2x Bearing/Lager 608 Z (7x8x22mm)
2x Bearing/Lager 6901 Z (6x12x24mm)
10x Nut/Mutter M5
1x Part/Teil 8 - Bearing-disk/Lagerscheibe 1
1x Part/Teil 19 - Bearing-disk/Lagerscheibe 2
Top / Deckel - 1 Piece/Stück
182 x 65,5 x 4 mm
Includes holes for 3.5 mm screws, but the top fits perfectly without them. / Enthält Bohrungen für 3,5 mm Schrauben, aber der Deckel hält auch ohne sehr gut.
Shaft / Welle 1 - 1 Piece/Stück
12 x 50 mm
Part order / Reihenfolge der Teile
a - Part/Teil 6 - Crank/Kurbel
b - Part/Teil 7 - Spacer/Distanzstück 1
c - Part/Teil 8 - Bearing-disk/Lagerscheibe 1
d - Bearing/Lager 61901 ZZ (6x12x24mm)
e - Part/Teil 9 - Clamp/Klemme 1
f - Part/Teil 10 - Spur gear/Stirnrad 1
g - Part/Teil 11 - Spacer/Distanzstück 2
h - Bearing/Lager 61901 ZZ (6x12x24mm)
The gear is rigidly connected to the shaft and spins with the crank rotation.
This shaft transmits the biggest torque. Both parts must be printed more durable
(4 perimeter, 4 solid top/bottom layers, infill 40%). The crank is glued to the outer
end of the shaft.
/
Das Zahnrad ist starr mit der Welle verbunden und rotiert mit der Kurbeldrehung.
Diese Welle überträgt das größte Drehmoment. Beide Teile müssen stabil gedruckt werden
(4 Umrissbahnen, 4 Volle Boden- und Dachschichten, Füllung 40%). Die Kurbel ist mit dem
äußeren Wellenende verklebt.
Shaft / Welle 2 - 2 Piece/Stück
8 x 54 mm
Part order "shaft 4 gears" / Reihenfolge der Teile "Welle mit 4 Zahnrädern"
a - Part/Teil 12 Spacer/Distanzstück 3
b - Assembly Doublegear without Part/Teil 18 Spacer/Distanzstück 7
c - Assembly Doublegear
d - Assembly Doublegear
e - Assembly Doublegear
f - Part/Teil 13 - Spacer/Distanzstück 4
g - Part/Teil 14 - Clamp/Klemme 2
Part order "shaft 3 gears" / Reihenfolge der Teile "Welle mit 3 Zahnrädern"
a - Part/Teil 15 Spacer/Distanzstück 5
b - Assembly Doublegear without Part/Teil 18 Spacer/Distanzstück 7
b - Assembly Doublegear
c - Assembly Doublegear
a - Part/Teil 16 - Spacer/Distanzstück 6
e - Part/Teil 14 - Clamp/Klemme 2
Assembly Doublegear - 7 Piece/Stück
a - Part/Teil 17 - Double spur gear / Doppelstirnrad
b - Bearing/Lager 608Z (7x8x22mm)
c - Part/Teil 18 - Spacer/Distanzstück 7
The gears are spinning freely on the shafts and transmit the torque.
The shafts can be printed with standard settings.
/
Die Zahnräder drehen frei auf den Wellen und übertragen das Drehmoment.
Die Wellen können mit Standardeinstellungen gedruckt werden.
Shaft 3 / Welle 3 - 1 Piece/Stück
8 x 62 mm
Part order / Reihenfolge der Teile
a - Part/Teil 19 - Bearing-disk/Lagerscheibe 2
b - Bearing/Lager 608Z (7x8x22mm) outside/außen
c - Part/Teil 20 - Spur gear/Stirnrad 2
d - Part/Teil 14 - Clamp/Klemme 2
e - Bearing/Lager 608Z (7x8x22mm) inside/innen
Crank/Kurbel - 1 Piece/Stück
181 x 34 x 10 mm
Part order / Reihenfolge der Teile
a - Bearing/Lager 61901 ZZ (6x12x24mm)
b - Part/Teil 21 - Spacer handle bearing/Scheibe Grifflager
c - Part/Teil 22 - Handle/Griff
d - Part/Teil 9 - Clamp/Klemme 1
e - Part/Teil 9 - Clamp/Klemme 1
f - Part/Teil 9 - Clamp/Klemme 1
g - Part/Teil 9 - Clamp/Klemme 1
f - Part/Teil 9 - Clamp/Klemme 1
The crank and the handle transmit a high bending moment. Both parts must be printed more durable
(3 perimeter, 3 solid top/bottom layers, infill 30%). The "spacer handle bearing" is glued.
/
Die Kurbel und der Griff übertragen ein hohes Biegemoment. Beide Teile müssen stabil gedruckt werden
(3 Umrissbahnen, 3 Volle Boden- und Dachschichten, Füllung 30%). Die "Scheibe am Grifflager" ist eingeklebt.
Spacer/Distanzstück 1 - 1 Piece/Stück
6.4 x 16 x 12 mm
Bearing-disk/Lagerscheibe 1 - 1 Piece/Stück
1 x 32 x 18 mm
Clamp/Klemme 1 - 6 Piece/Stück
10 x 20 x 12 mm
Spur gear/Stirnrad 1 - 1 Piece/Stück
Number of teeth / Zähnezahl: 30
Pitch circle / Wälzkreisdurchmesser: 67.5 mm
Hub diameter / Nabendurchmesser: 12 mm
Spacer/Distanzstück 2 - 1 Piece/Stück
2 x 16 x 12 mm
Spacer/Distanzstück 3 - 1 Piece/Stück
1,5 x 12 x 8 mm
Spacer/Distanzstück 4 - 1 Piece/Stück
2,25 x 12 x 8 mm
Clamp/Klemme 2 - 3 Piece/Stück
10 x 16 x 8 mm
Spacer/Distanzstück 5 - 1 Piece/Stück
6 x 12 x 8 mm
Spacer/Distanzstück 6 - 1 Piece/Stück
6,75 x 12 x 8 mm
Double spur gear / Doppelstirnrad - 7 Piece/Stück
Number of teeth / Zähnezahl: 15 and 30
Pitch circle / Wälzkreisdurchmesser: 33.75 and 67.5 mm
Hub diameter / Nabendurchmesser: 22 mm
Spacer/Distanzstück 7 - 5 Piece/Stück
2 x 12 x 8 mm
Bearing-disk/Lagerscheibe 2 - 1 Piece/Stück
1 x 29 x 18 mm
Spur gear/Stirnrad 2 - 1 Piece/Stück
Number of teeth/Zähnezahl: 15
Pitch circle/Wälzkreisdurchmesser: 33.75 mm
Hub diameter/Nabendurchmesser: 8 mm
Spacer handle bearing/Scheibe Grifflager - 1 Piece/Stück
2 x 29,5 x 21 mm
Handle/Griff - 1 Piece/Stück
12 x 58 mm
In order for the gears to work well together, the 3D printer should be
calibrated properly and produce clean external surfaces. If possible
aline the starting points of the outer perimeters and
remove the plastic bumps in a single cut.
The shafts are constructed without play. If the parts are not
plug into each other, STL files must be downsized in the radial direction.
Some parts includes a clamping function with nuts and grub screws. I noticed during the assembly,
that the clamping can be implemented easier by variation of the parts dimensions.
After the assembly the gearbox might need some running time till the gears are working smoothly. Lubrication is very helpful.
/
Damit die Zahnräder gut miteinander arbeiten sollte der 3D-Drucker korrekt
kalibriert sein und saubere Außenflächen produzieren. Nach Möglichkeit setzt
man den Startpunkt der äußeren Bahnen übereinander um die dortige
Kunststoffanhäufung mit einem Schnitt entfernen zu können.
Die Wellen sind ohne Spiel konstruiert. Falls sich die Teile nicht
ineinander stecken lassen, müssen STL-Dateien in radialer Richtung
verkleinert werden.
Bei einige Teile ist eine Klemmfunktion mit Muttern und Madenschrauben vorgesehen. Ich habe während der Montage bemerkt,
dass die Klemmung durch Variation der Teileabmessungen einfacher zu realisieren ist.
Nach der Montage benötigt das
Getriebe einige Zeit, bis die Zahnräder reibungslos funktionieren. Schmierung ist sehr hilfreich.
Printparameter / Druckparameter
Printer / Drucker: Velleman K8200
Material: PLA
Temp. Extruder: 190 °C
Temp. Bed / Bett: 50 °C
Layerheight / Schichthöhe: 0.25 mm
Perimeters / Umrissbahnen: 2 - 4
Solid Top Bottom Layer / Volle Boden- und Dachschichten: 2
Infill / Fülldichte: 40 %
No Support needed / keine Stützkonstruktion nötig
https://www.youtube.com/watch?v=84odyuiceQc
Similar models
thingiverse
free
BBQ Fan Extension for Gearbox 256 / Grillgebläse Erweiterung für Getriebe 256 by CONSTRUCTeR
...ichten: 2
infill / fülldichte: 40 %
no support needed / keine stützkonstruktion nötig
https://www.youtube.com/watch?v=qsjrnm_caje
thingiverse
free
WLAN Thermo Mini V2 - official case by J3DI
...r ein fertiges, hochwertig gedrucktes gehäuse sucht kann sich gerne an (m)einen 3d-hub wenden oder hier kontakt zu mir aufnehmen.
thingiverse
free
Radmutternkappe 19 mm by Rolfiklein
...höhe.
es empfiehlt sich zuerst 1 stück zu drucken und die leichtgängigkeit zum aufstecken zu prüfen. evtl. geringfügig skalieren.
thingiverse
free
Angle adjustable polariser and Lambda/4-plate - Polarisator mit Winkelskale by Ce-ha
...l 3 ist "studenten- / schülersicher" gestaltet, da es sich nur mit dem montageschlüssel ein- und herausschrauben lässt.
thingiverse
free
Planetengetriebe für nema 17 Verhältniss 1:5 by Mastieb
...und motor in einem stück in den
original micro swiss alu extruder passt, später wird das ganze komplett ohne aluträger
adaptiert.
thingiverse
free
Görgesklemme 20mm Desk Clamp by HannesLurk
...saals 226 im görgesbau der tu-dresden.
die zweite einfach kopieren und spiegeln.
mit stützmaterial nach belieben gedreht drucken.
thingiverse
free
Jalousie Kurbel Handgriff by Resea
... hoch montiert wurde. eine komplette ersatzkurbel kostet um 40 euro. die hülse kostete mich nur zeit und kunststoff zum druck :-)
thingiverse
free
Garden Sprinkler by konst57
...d besser.
der innendurchmesser der aufnahme ist 23 mm.
ich habe noch die klemme und 2 verbindungsstücke für 1/2 " beigefügt.
thingiverse
free
Beamer-Kamera Stativ Adapter by Polle
...last
p.s.: noch konnte ich meine konstruktion noch nicht selbst testen, daher würde ich mich über ein feedback von euch freuen.
thingiverse
free
Garmin Zumo XT Sonnenblende Blendschutz " Diebstahlsicherung " by Gibi50
...st bei mir- super!
das entriegeln des navigationsgerät erfolgt unter zuhilfenahme z.b. des fahrzeugschlüssel -siehe gelber pfeil-
Getriebe
thingiverse
free
Stopfen für Ford Getriebe by Evolution500
...tion500
thingiverse
stopfen für das getriebe wenn die antriebswelle demontiert wird.
damit läuft dann nicht das ganze öl hinaus.
thingiverse
free
Motorspant T-Race 23 für Reisenauer Getriebe by Kippe
...ippe
thingiverse
motorspant für den t-race 23 von aer-o-tec
mit reisenauer micro edition getriebe.
und servobrett für kst ds 315
thingiverse
free
Dnepr & Ural Beluefter (Breather) für Getriebe und Endantriebe by cyboli
...system. rainproof and pressure washer proof. you need a 4mm diameter pneumatic tube and a qs-fitting screwed in the oil dipstick.
thingiverse
free
Front Motor Mount for RC Modelex Transmission Getriebe by domi1974
... and so i needed to design a mount. the part is from rc modelex. to mount it you need rails that have some spare mounting points.
thingiverse
free
Propeller for Planetary gear by Smuk3D
...gear by smuk3d thingiverse ein propeller fuer das planeten getriebe ...
thingiverse
free
Siku Control Getriebeschutz für Frontlader by tim786
...siku control getriebeschutz für frontlader by tim786
thingiverse
schützt das getriebe des frontladers vor verschmutzung.
thingiverse
free
Gearbox_Getriebe 4:1 by CrazyT87
...gearbox_getriebe 4:1 by crazyt87
thingiverse
getriebe 4:1 für wellendurchmesser 5mm
abstandshalter werden benötigt.
thingiverse
free
Kia Sorento JC by Clartos
...jc by clartos thingiverse kia sorento jc bj: 2005 getriebe elektrischer anklappbarer...
thingiverse
free
BBQ Fan Extension for Gearbox 256 / Grillgebläse Erweiterung für Getriebe 256 by CONSTRUCTeR
...ichten: 2
infill / fülldichte: 40 %
no support needed / keine stützkonstruktion nötig
https://www.youtube.com/watch?v=qsjrnm_caje
256
3ddd
$1
Диван BUSNELLI Divano 256
...ano 256
3ddd
busnelli divano 256 , busnelli
диван busnelli divano 256
vray 2014,2011,obj
3d_export
$25
modern villa model 256
...modern villa model 256
3dexport
turbosquid
$9
Sartory Rugs Nc-256
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$2
Memory Card 256 MB
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$55
Condo 256 3D Model
...iture accessories complete full detailed photorealistic textures materials render ready
condo 256 3d model barmoon 42748 3dexport
3d_export
$155
Building 256 3D Model
...terior resort hotel bank office center university college campus street landscape
building 256 3d model rosestudio 54589 3dexport
3d_export
$60
Architecture 256 3D Model
...lege campus max street landscape commercial building medical hospital offices
architecture 256 3d model lotusmodel 47915 3dexport
3d_export
$30
Villa 256 3D Model
...st suburban architecture building residential suburbs two story vinyl siding house set
villa 256 3d model freebird 49518 3dexport
3d_export
$160
3d building 256 3D Model
...erior vray sitting accesorie apartment home visualization sofa couch table chair
3d building 256 3d model kanhtart 44253 3dexport
3d_export
$50
3D Home 256 3D Model
... chair furniture texture table lamp apartment rug carpet restaurant hotel sitting
3d home 256 3d model richard3015 46106 3dexport
Gearbox
3d_export
$7
planetary gearbox
...planetary gearbox
3dexport
planetary gearbox
3d_export
$5
transmission gearbox
...transmission gearbox
3dexport
transmission gearbox
3d_export
$30
differential gearbox
...differential gearbox
3dexport
3d model of a differential gearbox.<br>modeled in solidworks.<br>rendered in keyshot.
turbosquid
$4
planetary gearbox
...royalty free 3d model planetary gearbox for download as blend on turbosquid: 3d models for games, architecture, videos. (1423384)
3d_export
$5
three stage planetary gearbox
...three stage planetary gearbox
3dexport
three stage planetary gearbox
turbosquid
$31
2 speed reducer Gearbox
... dual stage helical speed reducer gearbox for download as iam on turbosquid: 3d models for games, architecture, videos. (1650029)
3d_export
$15
automatic processing line for gearbox pump body
...automatic processing line for gearbox pump body
3dexport
automatic processing line for gearbox pump body
3d_export
$1000
Automobile Manual Transmission mechanism Gearbox 3D Model
...ox 3d model
3dexport
transmission gearbox
automobile manual transmission mechanism gearbox 3d model daveterminator 24996 3dexport
3d_export
$8
tool replacement gearbox
...tool replacement gearbox
3dexport
eccentric lifting mechanism, you can process according to available drawings.
3d_export
$7
milling machine spindle drive diagram - milling gearbox
... n = 4500 rin / min; maximum power p = 7.5 kw. bt40 spindle, like welcome to download to learn. there are igs format files in it.
Constructer
3d_export
$21
construction
...construction
3dexport
construction 8k texture
3d_export
$20
construction worker
...construction worker
3dexport
construction worker
3d_export
$65
Construction
...construction
3dexport
simple rendering of the scene file
3d_export
$65
Construction
...construction
3dexport
simple rendering of the scene file
3d_export
$65
Construction
...construction
3dexport
simple rendering of the scene file
3d_export
$65
Construction
...construction
3dexport
simple rendering of the scene fil
3d_export
$65
construction
...construction
3dexport
simple rendering of the scene file
3d_export
$5
construction barrier
...construction barrier
3dexport
construction barrier + 8k texture
3d_export
$5
construction barrier
...construction barrier
3dexport
construction barrier + 8k texture
3d_ocean
$19
Steel Construction
...steel construction
3docean
construction frame h-beam house steel
4 models of steel construction. maya, obj, fbx