Thingiverse
GBS Control Case for GBS 8200 by TheJeffChen
by Thingiverse
Last crawled date: 3 years, 5 months ago
My version of GBS Control case for GBS 8200 and two sizes of ESP8266 modules, plus RGBS BNC connectors.
The two sizes of the ESP8266 module supported are:
48 x 25mm
58 x 31mm
Please choose the corresponding one when you print.
Project is put together with M3 hex screw and nuts. The outer shell uses 22.8mm ones. The sockets use 11mm ones.
I had to design sleeves for the hex screws since the longest one I had was 22.8mm. You may want to use raft when printing the screw sleeves. However mine didn't require that.
The top and bottom pieces are printed better upright.
The rim is printed better upside-down. Support is recommended for better port accuracies.
The supported BNC connector is 9.3mm in diameter, panel mounted.
The two sizes of the ESP8266 module supported are:
48 x 25mm
58 x 31mm
Please choose the corresponding one when you print.
Project is put together with M3 hex screw and nuts. The outer shell uses 22.8mm ones. The sockets use 11mm ones.
I had to design sleeves for the hex screws since the longest one I had was 22.8mm. You may want to use raft when printing the screw sleeves. However mine didn't require that.
The top and bottom pieces are printed better upright.
The rim is printed better upside-down. Support is recommended for better port accuracies.
The supported BNC connector is 9.3mm in diameter, panel mounted.
Similar models
thingiverse
free
GBS Control Case for GBS 8220 with BNC for RGBs by TheJeffChen
...ckets use m38mm (11mm total length) ones.
bnc connector should be rear-threaded. flange diameter should be no bigger than 12.4mm.
thingiverse
free
GBS Control Case for GBS 8200 with SCART in and HDMI out by kistvan88
...first attempt at 3d "modeling" so no guarantees. i think everything applies to this modell that applies to the authors.
thingiverse
free
Portable Balun Case by do1hfs
...alun-case print in pla without support.
stopfen in tpu.
use an bnc connector for the balun.
i use this balun case for my 9:1unun.
thingiverse
free
EspoTek Labrador Case by bostwickenator
...tors and use proper probes for your work.
the bnc connectors used were obtained here https://www.amazon.com/gp/product/b07dgv6482
thingiverse
free
Case for Step Down Module (B3603) by norm8332
.... added a kickstand for better ergonomics. lid is friction fit. all screws are 3mm. the fine pitch screws used in pcs work well.
thingiverse
free
MAX7219 LED Matrix + ESP8266 case by frog03
...and a wemos d1 mini.
you might break a few clips when inserting the led modules, but there are enough, so it should not matter :)
thingiverse
free
Controller Stick PS4_Aim Hex nut by Kev22
...use of the material). i prefer to print it in tpu for a better sense.
print it with the hexagon on bottom and activate support!!
thingiverse
free
GBS 8200 HDMI housing by Stargrove1
...additional parts for assembly
4 x m3 * 18 flat head screws
since gbs control is heavily recommended, the buttons are not exposed.
thingiverse
free
GBS-8220 case by tankgrrl
...re's a little extra gap on the right of the component inputs. i'm inclined to leave it as it doesn't affect anything.
thingiverse
free
Cold frame (greenhouse) for .5" PVC by Aawon
...s (but not the center top one).
clips: to hold the plastic
ventilation holder: to hold an extra pvc pipe for to allow for a vent
Thejeffchen
thingiverse
free
Toothpaste Squeezer by TheJeffChen
...by thejeffchen
thingiverse
my neighbor wanted one, so i designed it. no moving parts means no chance to break. hope you like it.
thingiverse
free
Nintendo Console Ports STEP by TheJeffChen
...nintendo console ports step by thejeffchen
thingiverse
nintendo console ports i designed for my own projects.
thingiverse
free
PlayStation 2 Slim Stand by TheJeffChen
...tation 2 slim stand by thejeffchen
thingiverse
created a while ago.
attaches to ps2 slim with one m3 screw.
nothing complicated.
thingiverse
free
Famicom Front Expansion Port Cover by TheJeffChen
...amicom front expansion port cover by thejeffchen
thingiverse
famicom front expansion port cover for those who lost the original.
thingiverse
free
USB Coupler by TheJeffChen
...sed:https://www.amazon.com/gp/product/b07np7jryx/https://www.amazon.ca/gp/product/b07np7jryx/
pins used: 2.54mm pitch pin header.
thingiverse
free
IKEA MAMMUT Table Leg Extension 10cm by TheJeffChen
...s piece of cheap furniture. print 4 of them and you are good to go.
i used pla and it's holding up fine. no need for support.
thingiverse
free
GDEMU Mount Button Flat & Raised Logo by TheJeffChen
...go file.
if your printer is as dumb as mine, you can print the flat button and the swirl logo separated, then glue them together.
thingiverse
free
iPhone 12 MagSafe Add-on for Belkin Charge + Sync Dock by TheJeffChen
...ly.
choose the one you like.
use m2 screws and nuts to assemble.
if interests are high, i can make a stand-alone version as well.
thingiverse
free
Apple Remote Bundle Shell with AirTag by TheJeffChen
...for a snug installation.
however the front facing version was my original idea and it doesn't feel that bad either.
have fun!
thingiverse
free
GBS Control Case for GBS 8220 with BNC for RGBs by TheJeffChen
...ckets use m38mm (11mm total length) ones.
bnc connector should be rear-threaded. flange diameter should be no bigger than 12.4mm.
8200
thingiverse
free
Support Dremel 8200 by manupp74
...8200 by manupp74
thingiverse
dremel support 8200 and other
the pieces fit perfectly, if necessary give a little bit of sandpaper
thingiverse
free
emco toolpost dremel 8200 mount by iainanderson
...emco toolpost dremel 8200 mount by iainanderson
thingiverse
mounts a dremel 8200 cordless to an emco compact 5
thingiverse
free
Dremel 8200 drill press adapter by Motorpixiegimbals
...ixiegimbals
thingiverse
adapter that allows you to mount a dremel 8200 style drill into a drill press with a mount hole of 38mm.
thingiverse
free
Dremel 8200 battery container by Ghiotto
...mel 8200 battery.
people says its compatible wth bosch 10.8v /12v system.
also can be used for ac-dc connector instead of battery
thingiverse
free
dremel 8200 drill press and vise adapter by tcbilge
...remel 8200 drill press and vise adapter by tcbilge
thingiverse
drill press adapter & vise adapter for dremel 8200 hand tool.
thingiverse
free
GBS 8200 v4.0 enclosure by dnhutchins
... cga/ega/yuv to vga converter board. print the top section standing on end, with the vent lines running up/down without supports.
thingiverse
free
GBS 8200 HDMI housing by Stargrove1
...additional parts for assembly
4 x m3 * 18 flat head screws
since gbs control is heavily recommended, the buttons are not exposed.
thingiverse
free
GBS-8200/8220 Upscaler Enclosure by Zhixalom
...table, or on a wall, etc.
this was made with tinkercad, so it can be modified online:https://www.tinkercad.com/things/117uyiisbk1
thingiverse
free
D-link DCS 8200 lh support for Prusa I3 Mk2 by davidwt2
...s 8200 lh to apply to a prusa i3 mk2. i use it to monitoring print process from remote and in the same time monitoring the room.
thingiverse
free
GBS Control Case for GBS 8200 with SCART in and HDMI out by kistvan88
...first attempt at 3d "modeling" so no guarantees. i think everything applies to this modell that applies to the authors.
Gbs
thingiverse
free
gd gb
...gd gb
thingiverse
well its a gd gb
thingiverse
free
GB-22
...gb-22
thingiverse
gb-22 single shot zip gun in .22 long rifle
thingiverse
free
gb keychain
...gb keychain
thingiverse
goldenboy logo
thingiverse
free
GBS Control Case for GBS 8200 with SCART in and HDMI out by kistvan88
...first attempt at 3d "modeling" so no guarantees. i think everything applies to this modell that applies to the authors.
thingiverse
free
GB-BRK-CART/32K-A shell by lpla
...t32k-a (https://oshpark.com/shared_projects/phwqw0kh) and gekkio gb-brk-cart (https://github.com/gekkio/gb-hardware#gb-brk-cart).
thingiverse
free
Soporte SMA GB Race by GBFrames
...soporte sma gb race by gbframes
thingiverse
soporte de sma parra el gb race
thingiverse
free
GB Fancy Logo/Pendant for by seth__jk
...go/pendant for by seth__jk
thingiverse
this is a custom pendant/logo thing that has the initials gb. i made it for dawson <3
thingiverse
free
GB £ shopping trolley keyring token by Rubertel
...gb £ shopping trolley keyring token by rubertel
thingiverse
gb pound shopping trolley keyring token
thingiverse
free
GBS 8200 case modified for Scart/GBS Control
...also cleaned up some of the circles. should work fine but tell me how it goes. will update when i'm able to test it saturday.
Control
thingiverse
free
Megapoints Controllers - Servo Controller by SoBaldrick
...megapoints controllers - servo controller by sobaldrick
thingiverse
megapoints controllers - servo controller base
thingiverse
free
controller by tahmasnx
...controller by tahmasnx
thingiverse
controller fusion 360
thingiverse
free
Control panel
...control panel
thingiverse
control panel for scuba regulator/bank system
thingiverse
free
ph controller
...ph controller
thingiverse
pi zero based reef-pi ph controller
thingiverse
free
NES Controller
...nes controller
thingiverse
this is just a simple nes controller prop. display purposes only.
thingiverse
free
Frame control
...frame control
thingiverse
installation led 12864 reprapdiscount for control machine 3d printer.
thingiverse
free
Control Tower
...control tower
thingiverse
control tower or marshall tower for 1/32 slot car track
thingiverse
free
Controller Hook by P0chapa
... for (maybe) any game controller.
i attached this thing to ps2 controller and third-party xbox controller with double sided tape.
thingiverse
free
Xbox 360 controller stand for 3 controllers by afrolucas
...xbox 360 controller stand for 3 controllers by afrolucas
thingiverse
update for 3 controllers
thingiverse
free
PS4 Controller Stand for 3 Controllers (Dualshock 4)
...the stands for a nvidia shield controller rather than a ps4 controller (so two ps4 controllers and one nvidia shield controller).
Case
thingiverse
free
Case
...case
thingiverse
case
thingiverse
free
Case
...case
thingiverse
case
thingiverse
free
case
...case
thingiverse
case for https://www.thingiverse.com/thing:4008790
case printed in surface mode
thingiverse
free
Case
...case
thingiverse
detector case first try
thingiverse
free
Case
...case
thingiverse
this is case for electrical components.
i used it for my led transformer.
thingiverse
free
Case
...case
thingiverse
this is a self created model of a case. it is desigend to be printed in a size of 15%.
thingiverse
free
case by milesman20051
...case by milesman20051
thingiverse
case
thingiverse
free
case by zyzomys
...case by zyzomys
thingiverse
case
thingiverse
free
CAse by Ryutaka18
...case by ryutaka18
thingiverse
case
thingiverse
free
case by johnboyjr
...case by johnboyjr
thingiverse
case