Cults
Fully Printable Collective Pitch RC helicopter.
by Cults
Last crawled date: 6 years, 3 months ago
Disclaimer:
Be careful with high speed rotating parts. Improper printing or assembly, or inferior materials, may cause problems. Centrifugal forces of the blades will be be under 40 N at 4000 rpm, but they are not harmless if something shatters. Avoid hovering with the blades at eye level without protective goggles.
News:
I'm pretty much finished with the design. It flies great and works reliably.
News:
Changed the nose a bit. Made it narrower, and it looks a little more balanced now. The camo one pictured has the new shape. All parts should print without additional supports now.
Assembly notes:
-I attached an exploded view of the head and swash plate. The arrows marked "CA" indicate where you should use a tiny amount of CA glue (superglue/crazy glue) to bond the swash plate and bearing together.
-The main rotor head and swash plate need to be adjusted so that they operate at the same cyclic phase. This is done by turning the washout arm. If your flybarless gyro unit does not have software phase adjustment (for example KDS EBAR or Tarot ZYX S2), then your pitch links will have to run diagonally to achieve a synchronized swash plate. The prototype has a KDS EBAR V2 and flies fine with diagonal links. The Mikado mini V-Bar (and clones), BeastX and other more expensive units have swash plate phase adjustment in software, so you can do this adjustment via your computer and keep the pitch links vertical. This is preferable. I may change the design so that the servos , swashplate and head are synced mechanically, but decided against it now because it might be confusing to builders to set up.
-Install servos with thick double sided tape or hot glue. I used double sided tape for the prototype. The tabs of the recommended servos fit in the slots in the main frame. If you are using different servos you probably have to cut off the bottom tab and can install it with just hot glue.
-The clamping screws of the gear, head and shaft collar must be tightened carefully. It helps to print these parts with slightly higher temperature to ensure good layer adhesion.
-The landing gear slots into the main frame and is designed to stay locked in place, and come off in case of a crash, but the tabs will wear with frequent disassembly. I use thick CA to keep it in place after this happens.
-PLA pinions wear down relatively quickly, so it's useful if the landing gear is removeable. I might improve the solution later on. I tried Taulman 910 nylon for the pinion and it's lasting much longer now.Steel pinions are available. 13 teeth and 32p or 0.8 module will work. Axial AX30724 13T Steel Pinion Gear 32p 3mm is such a gear.
-The gear set with the large pinion will need the pinion to be installed onto the motor shaft after the motor is installed. This is because the pinion is too large to fit between the motor attachment screw holes without compromising the security of the motor installation.
-The tail rotor has to be twisted by hand after printing. You can adjust the pitch as necessary when you tune the tail.
-The tail rotor has two small holes around the hub. Insert a screw in one or both of the holes to engage with the spokes of the outrunner tail motor. Otherwise it will slip on the shaft. If the second hole doesn't line up with a spoke you can insert the second screw from the other side to act as a counterbalance so the rotor spins without vibration.
Videos:
https://youtu.be/Us8hcsxFzpM
https://youtu.be/8GmalS5hhr4
https://youtu.be/94xkn27AZd0
Required hardware:
3x75mm main shaft. Make from carbon rod or steel. No drilling required.
Two 3x6x2,5mm ball bearings for the main shaft: https://www.banggood.com/Orlandoo-F150-OH35P01-KIT-Parts-30625-Ball-Bearing-TA0009-p-985250.html?p=HD240528697332015103
Eight 2x5x2,5mm ball bearings for the blade grips.
One 10x15x4mm ball bearing for the swash plate: https://www.banggood.com/FS-Racing-FS-53910-FS-53625-6PCS-582002-Roll-Bearing-10x15x4mm-110-RC-Car-Parts-p-1153527.html?p=HD240528697332015103
Assorted #0 screws or similar self tapping 1-1,5mm diameter screws and ~6mm (~1/4") length.
Two M2x6mm screws for the main rotor blades and motor installation.
Four M2x18mm screws for the blade grips.
Four M2x10mm screws for installing the main rotor blades.
Short lengths of M2 threaded rod to hold the pitch and roll control rods together.
Servos:
https://www.banggood.com/JX-Servo-DHV56MG-5_6g-Coreless-LV-Low-Voltage-DSMG-Metal-Gear-Servo-0_89kg-0_10sec-p-1034036.html?p=HD240528697332015103
https://hobbyking.com/en_us/turnigytm-tgy-d56lv-coreless-low-voltage-ds-mg-servo-0-89kg-0-10sec-5-6g.html
Tail motor:
https://hobbyking.com/en_us/ntm-prop-drive-13-12-2400kv-40w.html
Main motor:
https://hobbyking.com/en_us/turnigy-2211-brushless-indoor-motor-2300kv.html (Needs longer shaft out the bottom end. Easy modification)
2100-3000kv motor should work fine.There are gears for two ratios in the files. The one with the small pinion fits higher kv motors. I attached photos showing how to change the shaft on typical quadcopter motors, which work great for micro helis of this size. Carbon fiber shafts are best when using PLA pinions because they don't transfer heat from the motor well, and CA sticks better to carbon fiber rods than steel shafts.
ESC:
Any small 3S capable ESC. I used 6A ESC for the tail and 10 A ESC for the main motor because that's what I had. 6A ESCs are probably enough for both motors. One ESC needs BEC, the other can be OPTO.
Battery:
3S 450mAh or similar:
https://www.banggood.com/Gaoneng-GNB-11_1V-450mAh-80160C-3S-Lipo-Battery-JSTXT30-Plug-p-1165484.html?p=HD240528697332015103
https://hobbyking.com/en_us/turnigy-nano-tech-450mah-3s-65c-lipo-e-flite-compatible-blade-180cfx-eflb4503sj30.html
The battery tray fits up to 30 mm wide batteries.
I used a KDS EBAR V2. Works well. ZYX S2, V-Bar mini or similar works just as good: https://www.banggood.com/Tarot-ZYX-S2-3-Axis-Gyro-System-ZYX23-USB-Programmer-Link-p-91613.html?p=HD240528697332015103
Be careful with high speed rotating parts. Improper printing or assembly, or inferior materials, may cause problems. Centrifugal forces of the blades will be be under 40 N at 4000 rpm, but they are not harmless if something shatters. Avoid hovering with the blades at eye level without protective goggles.
News:
I'm pretty much finished with the design. It flies great and works reliably.
News:
Changed the nose a bit. Made it narrower, and it looks a little more balanced now. The camo one pictured has the new shape. All parts should print without additional supports now.
Assembly notes:
-I attached an exploded view of the head and swash plate. The arrows marked "CA" indicate where you should use a tiny amount of CA glue (superglue/crazy glue) to bond the swash plate and bearing together.
-The main rotor head and swash plate need to be adjusted so that they operate at the same cyclic phase. This is done by turning the washout arm. If your flybarless gyro unit does not have software phase adjustment (for example KDS EBAR or Tarot ZYX S2), then your pitch links will have to run diagonally to achieve a synchronized swash plate. The prototype has a KDS EBAR V2 and flies fine with diagonal links. The Mikado mini V-Bar (and clones), BeastX and other more expensive units have swash plate phase adjustment in software, so you can do this adjustment via your computer and keep the pitch links vertical. This is preferable. I may change the design so that the servos , swashplate and head are synced mechanically, but decided against it now because it might be confusing to builders to set up.
-Install servos with thick double sided tape or hot glue. I used double sided tape for the prototype. The tabs of the recommended servos fit in the slots in the main frame. If you are using different servos you probably have to cut off the bottom tab and can install it with just hot glue.
-The clamping screws of the gear, head and shaft collar must be tightened carefully. It helps to print these parts with slightly higher temperature to ensure good layer adhesion.
-The landing gear slots into the main frame and is designed to stay locked in place, and come off in case of a crash, but the tabs will wear with frequent disassembly. I use thick CA to keep it in place after this happens.
-PLA pinions wear down relatively quickly, so it's useful if the landing gear is removeable. I might improve the solution later on. I tried Taulman 910 nylon for the pinion and it's lasting much longer now.Steel pinions are available. 13 teeth and 32p or 0.8 module will work. Axial AX30724 13T Steel Pinion Gear 32p 3mm is such a gear.
-The gear set with the large pinion will need the pinion to be installed onto the motor shaft after the motor is installed. This is because the pinion is too large to fit between the motor attachment screw holes without compromising the security of the motor installation.
-The tail rotor has to be twisted by hand after printing. You can adjust the pitch as necessary when you tune the tail.
-The tail rotor has two small holes around the hub. Insert a screw in one or both of the holes to engage with the spokes of the outrunner tail motor. Otherwise it will slip on the shaft. If the second hole doesn't line up with a spoke you can insert the second screw from the other side to act as a counterbalance so the rotor spins without vibration.
Videos:
https://youtu.be/Us8hcsxFzpM
https://youtu.be/8GmalS5hhr4
https://youtu.be/94xkn27AZd0
Required hardware:
3x75mm main shaft. Make from carbon rod or steel. No drilling required.
Two 3x6x2,5mm ball bearings for the main shaft: https://www.banggood.com/Orlandoo-F150-OH35P01-KIT-Parts-30625-Ball-Bearing-TA0009-p-985250.html?p=HD240528697332015103
Eight 2x5x2,5mm ball bearings for the blade grips.
One 10x15x4mm ball bearing for the swash plate: https://www.banggood.com/FS-Racing-FS-53910-FS-53625-6PCS-582002-Roll-Bearing-10x15x4mm-110-RC-Car-Parts-p-1153527.html?p=HD240528697332015103
Assorted #0 screws or similar self tapping 1-1,5mm diameter screws and ~6mm (~1/4") length.
Two M2x6mm screws for the main rotor blades and motor installation.
Four M2x18mm screws for the blade grips.
Four M2x10mm screws for installing the main rotor blades.
Short lengths of M2 threaded rod to hold the pitch and roll control rods together.
Servos:
https://www.banggood.com/JX-Servo-DHV56MG-5_6g-Coreless-LV-Low-Voltage-DSMG-Metal-Gear-Servo-0_89kg-0_10sec-p-1034036.html?p=HD240528697332015103
https://hobbyking.com/en_us/turnigytm-tgy-d56lv-coreless-low-voltage-ds-mg-servo-0-89kg-0-10sec-5-6g.html
Tail motor:
https://hobbyking.com/en_us/ntm-prop-drive-13-12-2400kv-40w.html
Main motor:
https://hobbyking.com/en_us/turnigy-2211-brushless-indoor-motor-2300kv.html (Needs longer shaft out the bottom end. Easy modification)
2100-3000kv motor should work fine.There are gears for two ratios in the files. The one with the small pinion fits higher kv motors. I attached photos showing how to change the shaft on typical quadcopter motors, which work great for micro helis of this size. Carbon fiber shafts are best when using PLA pinions because they don't transfer heat from the motor well, and CA sticks better to carbon fiber rods than steel shafts.
ESC:
Any small 3S capable ESC. I used 6A ESC for the tail and 10 A ESC for the main motor because that's what I had. 6A ESCs are probably enough for both motors. One ESC needs BEC, the other can be OPTO.
Battery:
3S 450mAh or similar:
https://www.banggood.com/Gaoneng-GNB-11_1V-450mAh-80160C-3S-Lipo-Battery-JSTXT30-Plug-p-1165484.html?p=HD240528697332015103
https://hobbyking.com/en_us/turnigy-nano-tech-450mah-3s-65c-lipo-e-flite-compatible-blade-180cfx-eflb4503sj30.html
The battery tray fits up to 30 mm wide batteries.
I used a KDS EBAR V2. Works well. ZYX S2, V-Bar mini or similar works just as good: https://www.banggood.com/Tarot-ZYX-S2-3-Axis-Gyro-System-ZYX23-USB-Programmer-Link-p-91613.html?p=HD240528697332015103
Similar models
cults
free
Fully Printable Fixed Pitch RC helicopter.
...for the swash plate: https://www.banggood.com/fs-racing-fs-53910-fs-53625-6pcs-582002-roll-bearing-10x15x4mm-110-rc-car-parts-p-1153527.html?p=hd240528697332015103 assorted #0 screws or similar self tapping 1-1,5mm diameter screws and ~6mm (~1/4") length....
thingiverse
free
Fully Printable Fixed Pitch RC helicopter. by tahustvedt
...for the swash plate: https://www.banggood.com/fs-racing-fs-53910-fs-53625-6pcs-582002-roll-bearing-10x15x4mm-110-rc-car-parts-p-1153527.html?p=hd240528697332015103 assorted #0 screws or similar self tapping 1-1,5mm diameter screws and ~6mm (~1/4") length....
thingiverse
free
Fully Printable Collective Pitch RC helicopter. by tahustvedt
...for the swash plate: https://www.banggood.com/fs-racing-fs-53910-fs-53625-6pcs-582002-roll-bearing-10x15x4mm-110-rc-car-parts-p-1153527.html?p=hd240528697332015103 assorted #0 screws or similar self tapping 1-1,5mm diameter screws and ~6mm (~1/4") length....
cults
$1
Conversion kit for making a flyable Revell 1:32 Westland Lynx kit.
...https://hobbyking.com/en_us/active-hobby-132t-84-pitch-cnc-composite-spur-gear.html pinion: gws 0,3 mod 10t brass pinion (or similar 0,3 mod/84 pitch). main motor: eh200 brushless outrunner 4100kv,...
grabcad
free
DFC
...dfc
grabcad
connecting main rotor shaft to rotor blades and swash plate
grabcad
free
Tail rotor with swash plate
...main constant and when a rotor shaft is rotating, you will see how is changing a angle of blades of tail rotor within one cycle.
grabcad
free
HobbyKing Red Brick 200A ESC
...hobbyking red brick 200a esc
grabcad
https://hobbyking.com/en_us/hobbyking-red-brick-200a-esc-1.html
thingiverse
free
Tank truck by redrobrc
... escs with breakhttp://www.banggood.com/10a-esc-brushed-speed-controller-for-rc-car-and-boat-p-908719.html?p=la1820677103201407rs
cults
free
Fan guard with feet for 120mm fan.
...d.com/220v-12cm-solder-absorber-fan-for-soldering-iron-ktv-cabinet-p-1106793.html?p=hd240528697332015103&cur_warehouse=cn
thingiverse
free
Fan guard with feet for 120mm fan. by tahustvedt
...ggood.com/220v-12cm-solder-absorber-fan-for-soldering-iron-ktv-cabinet-p-1106793.html?p=hd240528697332015103&cur_warehouse=cn
Cp
3ddd
free
CP
...cp
3ddd
винный шкаф
винный шкаф cp mobili art. e106,винотека
3ddd
$1
CP mobili
...ili
3ddd
журнальный , cp mobili
стол журнальный, cp mobili tavolino piano vetro art e116
3ddd
$1
CP
...cp
3ddd
стеллаж
стеллаж_cp
turbosquid
$25
CP
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
CP Italian Furniture
...cp italian furniture
3ddd
cp italian furniture , комод
cp italian furniture
3ddd
$1
CP Italian Furniture
...cp italian furniture
3ddd
cp italian furniture , тумба
cp italian furniture
3ddd
$1
CP DI PERNECHELE
... pernechele , тумба
фабрика | manufacturer: cp di pernechele
turbosquid
$15
Grizzly CP
...
royalty free 3d model grizzly cp for download as fbx and obj on turbosquid: 3d models for games, architecture, videos. (1563882)
3ddd
$1
CP Mobili Exclusive Line
...cp mobili exclusive line
3ddd
cp mobili , тумба
cp mobili exclusive line
turbosquid
$5
Human CP
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Pitch
turbosquid
$9
Pitch PITCH black coin
...alty free 3d model pitch pitch black coin for download as max on turbosquid: 3d models for games, architecture, videos. (1621905)
turbosquid
$9
Pitch PITCH gold coin
...yalty free 3d model pitch pitch gold coin for download as max on turbosquid: 3d models for games, architecture, videos. (1621902)
turbosquid
$15
Football Pitch
...d model football pitch for download as 3ds, max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1481817)
turbosquid
$60
Football Pitch
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Mini Football Pitch
...free 3d model mini football pitch for download as max and fbx on turbosquid: 3d models for games, architecture, videos. (1254856)
turbosquid
$49
Soccer Pitch with Football
... soccer pitch with football for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1299796)
turbosquid
$35
Architecture House Pitch Roof
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$115
Cricket Practice pitch kit Pack
...kit pack for download as 3ds, obj, fbx, dae, and unitypackage on turbosquid: 3d models for games, architecture, videos. (1252374)
3d_export
$9
variable pitch conveyor
...any questions also you can email to me. designed with solidworks 2017, render with keyshot **************************************
cg_studio
$35
Baseball stadium pitch diamond low poly3d model
...bx .3ds .obj - baseball stadium pitch diamond low poly 3d model, royalty free license available, instant download after purchase.
Helicopter
3d_export
free
Helicopter
...helicopter
3dexport
helicopter
archibase_planet
free
Helicopter
...planet
helicopter apache military helicopter aircraft
helicopter apache n100512 - 3d model (*.3ds) for exterior 3d visualization.
archibase_planet
free
Helicopter
...helicopter
archibase planet
helicopter aircraft
helicopter bellh13 n040612 - exterior 3d visualization.
3ddd
$1
helicopter
...helicopter
3ddd
вертолет
toy helicopter
archibase_planet
free
Helicopter
...helicopter
archibase planet
helicopter aircraft
helicopter n200214 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Helicopter
...helicopter
archibase planet
helicopter aircraft
helicopter n190214 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Helicopter
...helicopter
archibase planet
helicopter aircraft
helicopter n030414 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Helicopter
...helicopter
archibase planet
helicopter aircraft
helicopter n160714 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Helicopter
...helicopter
archibase planet
helicopter aircraft
helicopter an 12 n160312 - 3d model (*.3ds) for exterior 3d visualization.
archibase_planet
free
Helicopter
...helicopter
archibase planet
helicopter aircraft
helicopter n110412 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
Remote
archibase_planet
free
Remote
...remote
archibase planet
tv remote remote controller remote
remote - 3d model for interior 3d visualization.
archibase_planet
free
Remote
...e
archibase planet
remote control remote controller remote
remote n140512 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
$1
Remote
...
turbosquid
royalty free 3d model remote for download as obj on turbosquid: 3d models for games, architecture, videos. (1487515)
3d_export
$5
Tv Remote
...tv remote
3dexport
tv remote
3d_ocean
$7
Remote controller
... control switcher tv remote
remote controller for tv, sound systems etc easy to edit textures photo real rendered with mental ray
turbosquid
$39
remote
...free 3d model remote for download as obj, fbx, blend, and dae on turbosquid: 3d models for games, architecture, videos. (1387531)
turbosquid
$5
remote
...free 3d model remote for download as 3ds, obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1401849)
archive3d
free
Remote 3D Model
...l
archive3d
tv remote remote controller remote
remote - 3d model for interior 3d visualization.
turbosquid
$11
Remote
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
remote
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Radio
archibase_planet
free
Radio
...radio
archibase planet
radio
radio - 3d model for interior 3d visualization.
archibase_planet
free
Radio
...radio
archibase planet
radio
radio - 3d model for interior 3d visualization.
3d_export
$10
radio
...radio
3dexport
radio 3d, ojb
archibase_planet
free
Radio
...radio
archibase planet
radio set wireless receiver wireless set
radio 2 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Radio
...radio
archibase planet
radio set wireless receiver wireless set
radio 7 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Radio
...radio
archibase planet
radio set wireless receiver wireless set
radio 10 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_ocean
$9
Vintage Radio
...vintage radio
3docean
old radio radio set vintage
this is a vintage radio modeled to help in interior design arrangements.
3d_ocean
$8
Radio Branu
...radio branu
3docean
detail radio vintage
vintage radio with detail
3d_export
$5
radio
...radio
3dexport
turbosquid
$25
Radio
...o
turbosquid
royalty free 3d model radio for download as max on turbosquid: 3d models for games, architecture, videos. (1203794)
Rc
3ddd
$1
RC Helicopter
...rc helicopter
3ddd
вертолет
mini rc helicopter
93.329 polys
3d_export
$7
rc helicopter model
...rc helicopter model
3dexport
rc helicopter model
3d_ocean
$25
RC F1
...rc f1
3docean
auto car control f1 formula race rc remote speed
remote control f1 car
turbosquid
$10
rc plane
...lane
turbosquid
free 3d model rc plane for download as blend on turbosquid: 3d models for games, architecture, videos. (1295828)
turbosquid
$100
RC Helicopter
...free 3d model rc helicopter for download as 3ds, max, and obj on turbosquid: 3d models for games, architecture, videos. (1298511)
turbosquid
$59
Drone with RC
...3d model drone with rc for download as 3ds, max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1363601)
3d_export
$70
rc helicopter 3D Model
...rc helicopter 3d model
3dexport
rc helocopter
rc helicopter 3d model babay 10536 3dexport
turbosquid
$75
RC buggy
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$39
RC Plane001
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$30
RC Jet
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Fully
turbosquid
$50
Drone fully rigged
...
royalty free 3d model drone fully rigged for download as max on turbosquid: 3d models for games, architecture, videos. (1282280)
turbosquid
$12
FULLY PARAMETRIC CHAIR
...alty free 3d model fully parametric chair for download as rvt on turbosquid: 3d models for games, architecture, videos. (1280209)
turbosquid
$10
firetruck-fully-rigged
...yalty free 3d model firetruck-fully-rigged for download as ma on turbosquid: 3d models for games, architecture, videos. (1653811)
turbosquid
$6
Fully rigged character
...ty free 3d model fully rigged character for download as blend on turbosquid: 3d models for games, architecture, videos. (1486076)
turbosquid
$3
Fully Rigged shark
...ee 3d model fully rigged 3d shark model for download as blend on turbosquid: 3d models for games, architecture, videos. (1517695)
turbosquid
$75
Fully Customizable Hospital
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Fully Rigged Link
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
design_connected
$16
Troy W Fully Covered
...troy w fully covered
designconnected
magis troy w fully covered computer generated 3d model. designed by wanders, marcel.
cg_studio
$99
Pepe fully rigged3d model
...ully rigged3d model
cgstudio
.max - pepe fully rigged 3d model, royalty free license available, instant download after purchase.
3d_export
$60
Ankylosaur 8K - fully animated
...ankylosaur 8k - fully animated
3dexport
Collective
3ddd
$1
GIORGIO COLLECTION
...giorgio collection
3ddd
giorgio collection
giorgio collection
turbosquid
$99
Florence collections - furniture collection
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Jumbo Collection
...jumbo collection
3ddd
jumbo collection
диван jumbo collection
3ddd
$1
Jumbo collection
...jumbo collection
3ddd
jumbo collection
кресло jumbo collection
3ddd
free
Florence Collections
...florence collections
3ddd
florence collections , кресло
florence collections
3ddd
$1
Giorgio Collection
...и тумбочки giorgio collection , giorgio collection
кровать и тумбочки giorgio collection
3ddd
$1
Jumbo collection
...jumbo collection
3ddd
jumbo collection , капитоне
кресло jumbo collection
3ddd
$1
Giorgio Collection
...giorgio collection
3ddd
giorgio collection
производитель giorgio collection италия
3ddd
$1
Giorgio collection
...giorgio collection
3ddd
giorgio collection , круглый
giorgio collection table
3ddd
$1
Florence Collection
...florence collection
3ddd
florence collection
florence collection, текстуры есть
Printable
turbosquid
$5
printable giraffe
...uid
royalty free 3d model printable giraffe for download as on turbosquid: 3d models for games, architecture, videos. (1504825)
turbosquid
$49
Longhorn Printable
...
royalty free 3d model longhorn printable for download as stl on turbosquid: 3d models for games, architecture, videos. (1712930)
3d_export
$2
printable audi car
...printable audi car
3dexport
printable audi car
turbosquid
$40
Fox printable
...lty free 3d model fox printable for download as blend and stl on turbosquid: 3d models for games, architecture, videos. (1507558)
turbosquid
$23
Printable Statue
...ty free 3d model printable statue for download as obj and stl on turbosquid: 3d models for games, architecture, videos. (1415137)
turbosquid
$3
Ear Printable
...yalty free 3d model ear printable for download as obj and stl on turbosquid: 3d models for games, architecture, videos. (1671689)
turbosquid
$1
heart printable
...y free 3d model heart printable for download as stl and sldpr on turbosquid: 3d models for games, architecture, videos. (1209566)
turbosquid
$1
Printable Hook
...
royalty free 3d model 3d printable hook for download as stl on turbosquid: 3d models for games, architecture, videos. (1413683)
turbosquid
$30
Printable support
... model 3d printable support for download as max, 3ds, and stl on turbosquid: 3d models for games, architecture, videos. (1689342)
turbosquid
$24
Printable Dolphin
...el printable dolphin for download as , dae, fbx, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1602353)