FT arrow fuselage

...to make it stronger. it is put about an inch out from the fuselage to help reduce the noise from the wind shadow of the fuselage.

...or an ft mini arrow. i'm building the arrow without the center fuselage. designed for a 2204/2205/2206 standard hole pattern.

...flight test mini arrow fuselage by themakerdmitriredlin thingiverse flight test mini arrow fuselage.

... does bring the cog back, but the 1500mah battery compensates for it. the pod fits into a fuselage cavity measuring 35mm x 28mm.

...ft mini arrow - throw gauge by marikgl thingiverse throw gauge for ft mini arrow from flitetest.com

...ft mini arrow runcam swift holder by leden thingiverse runcam swift holder for ft mini arrow

...hot glue. printed in pla 0.3mm thick @30% infill. build video for the basic ft plane:https://www.youtube.com/watch?v=cd2ca2oskvs

...ft arrow front skid by gkjnt562 thingiverse print it out and glue it onto the front of your ft arrow with a lot of hot glue.

...hard nose by motorpixiegimbals thingiverse hard nose for the ft arrow. can be mounted on top of the existing nose if so desired.

...atch. this was designed to suit my mini board camera so you might need to get into the sketchup file to modify to suit your gear.

...fuselage by theroar thingiverse this is a fuselage for the wing i created.

...piper cub fuselage hook thingiverse simple hook for holding items up in the fuselage on cub.

...se support batterie et renfort du fuselage pour le zohd gt rebel. battery tray and fuselage reinforcement for the rebel zohd gt.

...age skin, this part is the outer skin of the fuselage and is 1 perimeter thick. 3) the nose skin, again this is 1 perimeter thick

...skyhunter fuselage bottom protection (skid) thingiverse skyhunter fuselage bottom protection skid

...ge glider made to be cut out of foam board and flown with an engine or throw power. could also be an interesting model to modify.

...le mount: through fuselage by implicit thingiverse dipole antenna mount, designed for the sma cable coming through the fuselage.

...tes the two hatches, it also reinforces the square pass through area between the battery and fc compartment. no special settings.

...flight test mini arrow fuselage by themakerdmitriredlin thingiverse flight test mini arrow fuselage.

...ft by colemanc thingiverse fh

...y ft-5) by h1hummerh3t thingiverse this is a conversation for the folgertech ft-5 making it into a corexy. by me- william puchot

...for ft versa wing with less air resistance than the original design inspired by http://flitetest.com/articles/ft-versa-wing-build

...unt by mbilke thingiverse i was looking for a way to mount the detachable faceplate for my ft-8900 and had a buddy draw this up.

...yaesu ft-2 ft-3 desk stand by waheiko thingiverse desk stand for yaesu handhelds

...ft edge tail support thingiverse ft edge tail support

...ft-5 idler by ramonseda thingiverse just an ft-5 idler

...ft cruiser canopy by rickpeck thingiverse this is a canopy for the larger ft cruiser. not for the mini.

...verse this is the firewall for flite tests ft spear. its actually just a remix of cannerbals ft firewall made to fit the spear.

...arrow thingiverse arrow

...arrow thingiverse just an arrow

...yondu arrow stand with arrow by demolitionx thingiverse yondu arrow stand and arrow

...arrow stop for 5,65 arrow thingiverse printmat.: tpu

...arrow holder for mini arrows by darklynx thingiverse holder for mini arrows.

...arrow stand (for weighing arrows) by rdp837 thingiverse simple stand to allow the weighing of arrows.

...arrow by littlejohn16 thingiverse arrow

...arrow by dylanwhitesel thingiverse arrow

...arrow holder for 12 arrows by christian1983 thingiverse a arrow holder i made with autodesk fusion 360.

...arrow bow thingiverse arrow bow