Thingiverse
FPV Antenna Jig by Karl33to
by Thingiverse
Last crawled date: 3 years, 1 month ago
Really useful jig for soldering 5.8ghz cloverleaf FPV antenna's.
All the components are held securely in place which makes it really easy to fine tune the position of the lobes and get everything soldered accurately.
1 - Insert your coax cable in from the bottom of the jig and tighten the three lower bolts to secure it firmly in place. You want to make sure it's nicely centered and the bolts aren't so tight that they damage the cable.2 - Insert one end of your lobe underneath the washer and loosely tighten the bolt, just enough to hold it in place.3 - Push the lobe inwards so that the bottom part of it is in contact with the outer part of the coax, then tilt it over to rest on the 45 degree support.4 - Tighten the bolt up so the lobe will not get knocked out of place easily - not too tight though as it's only plastic.5 - Bend the top of the lobe into position so that the top is in contact (or extremely close to) the inner part of the coax.6 - Repeat for all the lobes and solder with a fine tipped soldering iron.7 - Upload a photo to the makes and let me know if you liked it.
You will also need 6 x M3 hex bolts and 3 x M3 washers.
Designed for 0.8mm wire, but should also accommodate wire from 0.6 to 1.0mm in diameter.
I plan to add skew planar (4 lobe) jigs at a later date.
All the components are held securely in place which makes it really easy to fine tune the position of the lobes and get everything soldered accurately.
1 - Insert your coax cable in from the bottom of the jig and tighten the three lower bolts to secure it firmly in place. You want to make sure it's nicely centered and the bolts aren't so tight that they damage the cable.2 - Insert one end of your lobe underneath the washer and loosely tighten the bolt, just enough to hold it in place.3 - Push the lobe inwards so that the bottom part of it is in contact with the outer part of the coax, then tilt it over to rest on the 45 degree support.4 - Tighten the bolt up so the lobe will not get knocked out of place easily - not too tight though as it's only plastic.5 - Bend the top of the lobe into position so that the top is in contact (or extremely close to) the inner part of the coax.6 - Repeat for all the lobes and solder with a fine tipped soldering iron.7 - Upload a photo to the makes and let me know if you liked it.
You will also need 6 x M3 hex bolts and 3 x M3 washers.
Designed for 0.8mm wire, but should also accommodate wire from 0.6 to 1.0mm in diameter.
I plan to add skew planar (4 lobe) jigs at a later date.
Similar models
thingiverse
free
5760Mhz circular polarized antenna jig by aixelsyd
...e idea is to place your antenna wire into the jig as tightly fitting as possible. trim the ends and solder to the connector wire.
grabcad
free
Pentalobe Squarepants 5.8 gHz FPV antenna
...the rg402 making sure it is isolated with heat shrink. if you do not know what you are doing get a set of airblades from ibcrazy.
thingiverse
free
5.8Ghz Cloverleaf-SkewPlanar FPV Antenna Cover by mauricio2346
...d 3mm pigtail coax cables are included.
bottom covers and dome are snap-fit, so no glue is required. some ca is recommended.
thingiverse
free
Antenna Tool to Make 5.8ghz FPV Antenna by a_bit_of_a_menace
...his project
tools need to make the antenna
soldering iron
side cutter
cutting knife
how to make videohttps://youtu.be/imaikaashqe
thingiverse
free
Dipole Antenna Jig 1.2-1.3GHz by StuntDouble
...e or even 24 awg silicon wire.
there are 6 of the common 1.2-1.3ghz frequencies to choose from: 1200/1240/1258/1280/1320/1360 mhz
thingiverse
free
Antenna Soldering Jig - Skew Plannar + Clover Leaf - 5.8GHZ by Freakyattic
...zations.
now it is easier to solder the antenna, place all the parts in the jig and solder it at once!
enjoy it!
freakyattic.com
thingiverse
free
S helical 5.8ghz by runaway380
...this is a 5.8ghz antenna for the rg402 coax similar to a helical antenna. this should be printed in...
thingiverse
free
5.8ghz FPV clover leaf/ spw antenna jigs by 3dxl
...otoxl.com/real-object-design-for-hobby-models/real-object-design-for-hobby-models/xl-rcp-10-antenna-jigs-for-fpv/menu-id-118.html
thingiverse
free
Inverted Vee Antenna Jig 1.2-1.3GHz by StuntDouble
...e or even 24 awg silicon wire.
there are 6 of the common 1.2-1.3ghz frequencies to choose from: 1200/1240/1258/1280/1320/1360 mhz
thingiverse
free
Pagoda Antenna Jig by kellyullrich
... sides of the solder pads.
can be used on coax that already has the sma connector installed. some jig designs do not allow this.
Karl33To
thingiverse
free
Twisted Vase by Karl33to
...twisted vase by karl33to
thingiverse
my fist attempt at designing a vase and it turned out pretty awesome.
thingiverse
free
Car Battery Terminal Cover by Karl33to
...car battery terminal cover by karl33to
thingiverse
battery terminal covers to suit the halfords brand of battery terminals.
thingiverse
free
Dough Scraper by Karl33to
... out of your bowl.
flat edges on two sides to prevent it from digging into your hands.
size 120mm x x80mm
best if printed in tpu.
thingiverse
free
Drone Worx Hornet Motor Protector by Karl33to
...drone worx hornet motor protector by karl33to
thingiverse
arm and motor protector for the drone worx hornet v1 frame
thingiverse
free
Fibonacci Spiral Fidget Spinner by Karl33to
...33to
thingiverse
takes 3 standard skateboard bearings, 22mm od, 8mm id, 7mm thick.
example was printed at 0.2mm with 30% infill.
thingiverse
free
FPV Flightclub Proton Fin by Karl33to
...e
turtle mode fin for the fpv flightclub proton frame, just zip tie the two halves together.
approx weight is 9g for both parts.
thingiverse
free
Drone Worx Hornet Arm Protector by Karl33to
...rotector for the drone worx hornet v1 frame.
print in flexible filament for best results and attach using a small amount of glue.
thingiverse
free
Large Cable Clip by Karl33to
...ent so the wires can be pushed in and the opening will close back up again to prevent them falling out.
attach using 3m vhb tape.
thingiverse
free
Colour Gel Holder for LED Video Light by Karl33to
...hingiverse
clip on lighting gel holder for a raleno led video light.
this fits the 104 led model which measures 6.9×4.7×1.2inch.
thingiverse
free
Martian II Quadcopter Camera Wedge by Karl33to
...and gitup.
angle is 30 degrees.
tested in both pla and tpu. using tpu is preferable as it will reduce vibrations in your footage.
Jig
turbosquid
$25
jig-saw_mid_SM
...uid
royalty free 3d model jig-saw_mid_sm for download as obj on turbosquid: 3d models for games, architecture, videos. (1244761)
turbosquid
$20
jig-saw_low
...osquid
royalty free 3d model jig-saw_low for download as obj on turbosquid: 3d models for games, architecture, videos. (1244760)
turbosquid
$10
jig-saw_hi
...bosquid
royalty free 3d model jig-saw_hi for download as obj on turbosquid: 3d models for games, architecture, videos. (1244757)
turbosquid
$7
Jig Armchair
...squid
royalty free 3d model jig armchair for download as max on turbosquid: 3d models for games, architecture, videos. (1648936)
turbosquid
$5
Jig Head
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$5
Jig Head
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$5
Jig Head
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$5
Jig Head
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$5
Jig Head
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$5
Jig Tail
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Fpv
turbosquid
$1
FPV VTX Antenna
...e 3d model fpv vtx antenna for download as obj, fbx, and stl on turbosquid: 3d models for games, architecture, videos. (1230317)
3d_export
$9
Fpv logo 3D Model
...onogram vehicle part of auto transport 3d model logo emblem detailed high quality badge
fpv logo 3d model rmodeler 59628 3dexport
3d_export
$8
dji fpv battery slot holder
...er for 3 dji fpv batteries. holds perfectly without shaking. need 1 m3 countersunk head bolt. need to print 6 pin, 1 case, 1 cap.
3d_export
$10
fpv camera hd 700tvl
...aterials are logically named<br>the main format is in 3ds max 2009.<br>satisfcation garranteed..<br>thank you !
thingiverse
free
FpV Mount (SOPORTE FPV) by elborjas1987
...fpv mount (soporte fpv) by elborjas1987
thingiverse
this is a fpv mount with the same holes of naza base.
thingiverse
free
fpv by tbutera
...fpv by tbutera
thingiverse
fpv
thingiverse
free
fpv by tbutera
...fpv by tbutera
thingiverse
fpv
thingiverse
free
FPV DRONE ROOSTER DJI FPV PART
...fpv drone rooster dji fpv part
thingiverse
fpv drone rooster dji fpv install part
thingiverse
free
FPV monitor
...tml?rmmds=myorder&cur_warehouse=cn
link for download : https://cults3d.com/fr/mod%c3%a8le-3d/divers/fpv-monitor-ecran-fpv-faf
thingiverse
free
FPV receiver mount for FPV display by petrex
...eceiver mount for fpv display by petrex
thingiverse
aomway receiver mount for field view 777 fpv monitor. with small cable tray.
Antenna
archibase_planet
free
Antenna
...chibase planet
antenna aerial television antenna
antenna kathrein n090913 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Antenna
...antenna
archibase planet
satellite antenna
antenna 1 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Antenna
...antenna
archibase planet
equipment satellite antenna
antenna 2 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Antenna
...ntenna
archibase planet
satellite antenna equipment dish aerial
antenna 3 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Antenna
...antenna
archibase planet
satellite antenna dish dish aerial
antenna 4 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Antenna
...e planet
antenna dish dish aerial
antenna c-band satellite s180-g n210612 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
3d_export
$5
car antenna
...car antenna
3dexport
car antenna, antenna, car gadgets
turbosquid
$1
antenna
...rbosquid
royalty free 3d model antenna for download as blend on turbosquid: 3d models for games, architecture, videos. (1655786)
3d_export
free
Station with antenna
...station with antenna
3dexport
station with antenna
turbosquid
$5
Antenna
...id
royalty free 3d model antenna for download as max and fbx on turbosquid: 3d models for games, architecture, videos. (1381532)