Similar models
thingiverse
free
Flexure parallel gripper by nraynaud
... education on flexures.
i had best results with my pla when the thinest part of the hinge was 0.4mm, and the hinge width is 10mm.
thingiverse
free
Flexure by CBUEngineering
...flexure by cbuengineering
thingiverse
flexure part limits translational motion in the x direction
thingiverse
free
XY Table Stage flexure by ahmedjouirou
...h you an alternative way for moving in xy plane in minimalistic way . i planned to use this platform for laser/mirror alignment .
thingiverse
free
Flexure ball by CBUEngineering
...flexure ball by cbuengineering
thingiverse
this flexure ball limits motion of the middle section to just the x direction.
thingiverse
free
Cross-Axis Flexure Pivot by BYU_CMR
... other. cross-axis flexure pivots can replace pin joints in applications where wear and/or friction need to be low or eliminated.
thingiverse
free
Spherical flexure joint by Mr_SeLeNiO
...joint by mr_selenio
thingiverse
attempt to first spherical flexure joint design from https://www.youtube.com/watch?v=dangcygu7tc
thingiverse
free
Jubilee Tool Compression Flexures by reicheltcm
... are flexures needed for the jubilee toolchanger tools. normally these are laser cut and purchased but now you can 3d print them.
thingiverse
free
Hand Held Flexure Pliers by crreed
... scale to whatever size works best for you.
see full write up below:http://www.inventionfactory.xyz/2016/02/flexure-pliers.html
thingiverse
free
flexure demonstration on degrees of freedom by CBUEngineering
...flexure you limit the degrees of freedom, remove the rod to increase the number of degrees of freedom but you wont have them all.
thingiverse
free
Flexure - Spiral Disk by CBUEngineering
...flexure - spiral disk by cbuengineering
thingiverse
limits motion in the y direction
Darynfinney
thingiverse
free
FizzleFrames by DarynFinney
...hem daily, revising the design every time they broke (which was frequent at first). now i have new lenses and store bough frames.
thingiverse
free
Circuit Board Sorter by DarynFinney
...ith room in between each for surface mount components. included are files for two sizes of boxes, the one shown and a longer one.
thingiverse
free
Lotto Ticket Box by DarynFinney
...icator 2x. included are two .stl's for the lid, one with helpful tabs to prevent warping and can be cut off, and one without.
thingiverse
free
Magnetic Shock Absorber by DarynFinney
...hree in the top and bottom of each end with like polarities facing each other. the magnetic repulsion forces the shock to extend.
thingiverse
free
Armadillo From Amarillo by DarynFinney
... it up in your slicing software; this green one is about 150%.
http://www.123dapp.com/obj-catch/armadillo-from-amarillo/1907506
thingiverse
free
Hard Case, Custom by DarynFinney
...es, caped with included file. printed in abs with makerbot replicator 2x. https://darynfinney.wordpress.com/portfolio/gyro-case/
thingiverse
free
Three Color Lithopane by DarynFinney
...an .stl for the stand which holds a 3mm lithopane, the default setting from the site above, perfect for placing on a window sill.
thingiverse
free
Pet Door for Window by DarynFinney
...recently uploaded a zip file including the sw parts and assembly, as well as a step of the door for user modification as desired.
thingiverse
free
Saleen Mustang Wheel Center Cap and Seat Handles by DarynFinney
...me wheels.
edit: i've included a shorter version of the wheel hub for the are 5 spoke wheels used on same era saleen mustang.
Flexure
thingiverse
free
Flexure by CBUEngineering
...flexure by cbuengineering
thingiverse
flexure part limits translational motion in the x direction
thingiverse
free
Flexure ball by CBUEngineering
...flexure ball by cbuengineering
thingiverse
this flexure ball limits motion of the middle section to just the x direction.
thingiverse
free
Spherical flexure joint by Mr_SeLeNiO
...joint by mr_selenio
thingiverse
attempt to first spherical flexure joint design from https://www.youtube.com/watch?v=dangcygu7tc
thingiverse
free
Cross-Axis Flexure Pivot by BYU_CMR
... other. cross-axis flexure pivots can replace pin joints in applications where wear and/or friction need to be low or eliminated.
thingiverse
free
Flexure parallel gripper by nraynaud
... education on flexures.
i had best results with my pla when the thinest part of the hinge was 0.4mm, and the hinge width is 10mm.
thingiverse
free
Flexure - Spiral Disk by CBUEngineering
...flexure - spiral disk by cbuengineering
thingiverse
limits motion in the y direction
thingiverse
free
Jubilee Tool Compression Flexures by reicheltcm
... are flexures needed for the jubilee toolchanger tools. normally these are laser cut and purchased but now you can 3d print them.
thingiverse
free
Hand Held Flexure Pliers by crreed
... scale to whatever size works best for you.
see full write up below:http://www.inventionfactory.xyz/2016/02/flexure-pliers.html
thingiverse
free
Flexure Test Design by CBUEngineering
...flexure test design by cbuengineering
thingiverse
limiting motion to the y direction on both sides
Stages
thingiverse
free
Stage by mohamedbs
...stage by mohamedbs
thingiverse
objet de stage
thingiverse
free
model stage by pancala
...model stage by pancala
thingiverse
model stage
thingiverse
free
STAGE SETS by technoshopper
...stage sets by technoshopper
thingiverse
stage sets for dollhouse
thingiverse
free
Stage Concept by ProCadCam
...stage concept by procadcam
thingiverse
bird nest stage concept
thingiverse
free
Stage 2 by EBD03
...stage 2 by ebd03
thingiverse
stage 2 by eoghan [created on 3dtin]
thingiverse
free
BCS Stage by EBD03
...bcs stage by ebd03
thingiverse
bcs stage by eoghan [created on 3dtin]
thingiverse
free
Stage Supplement by agm2279
...stage supplement by agm2279
thingiverse
for use in lab to keep hemocytometer in place on microscope stage
thingiverse
free
Wrestling Stage by rowie4life
...wrestling stage by rowie4life
thingiverse
wrestling logo for a figure stage i'm making.
thingiverse
free
Coolio Stage by Nolas
...coolio stage by nolas
thingiverse
a cool stage thing i made for presenting stuff. should print okay
thingiverse
free
Artistic? Stage by kodera2t
...istic? stage by kodera2t
thingiverse
something artistic stage. it may be useless but may be suitable for your desktop object...?