Similar models
thingiverse
free
piece for orthogonal axis and bed center tests by penkerton
... the physical center. center circles should stay round. if it oval check your printer belts tension and that x and y move smooth.
thingiverse
free
Plumbcheck gizmo to verify X-Y-Z axes are orthogonal by nenadr
... all the angles were 90 degrees.
the end of the x axis of the gizmo is cut off to mark it, so i would know which axis is which.
thingiverse
free
bépo67 Split orthogonal keyboard by Makoto_Doushite
...bépo67 split orthogonal keyboard by makoto_doushite
thingiverse
bépo67 clavier orthogonal scindé wip
thingiverse
free
rs-2 servo orthogonal axis mount by eihis
...rs-2 servo orthogonal axis mount by eihis
thingiverse
an assembly for 2 rs-2 servos , with orthogonal axis
thingiverse
free
Clavier Orthogonal - Orthogonal Keyboard for 21th Computer by Makoto_Doushite
...to_doushite
thingiverse
wip design with freecad
for the moment, the right parts have mistakes, tagged in red in the main picture
thingiverse
free
Qidi Tech Heated Print Bed Power Connector Cap / Cover by cncartist
...rint bed power connector. to control the mess i created this connector cover and an "electricity logo" embedded on it.
thingiverse
free
Qidi Tech / Flashforge Creator Pro Interior Heated Bed Wire Hide Cover by cncartist
...der the print bed getting the underside area a little dirtier than i wanted. to control the mess i created this wire hide cover.
thingiverse
free
traxxas Stampede Rear Body Brace
...tly printing the bed brace. i haven't printed the the bed brace with bed installed on it and bed cap yet but it should work.
thingiverse
free
Di Vinci 2.0 full print bed test by 10sanitty
... each side and corner can be measured for uniformity.
it is 200x150x1mm. no brim, support or skirts they will print off the bed.
thingiverse
free
Kossel mini bed support by briggs007
...id not like the sound of glass rubbing a metal so i created this bed support.
this will fit a glass print bed with 20cm diameter.
Davebpix
thingiverse
free
Crab Token by davebpix
....
update: added .stl of 0.35 layer height version of same token. gcode for mp mini delta and 4x layout gcode for mp mini delta.
thingiverse
free
FlashCap Two Color by davebpix
...ps. made this version for those with dual extruder printers. enjoy!
printed in makergeeks crystal pla red and raptor pla yellow
thingiverse
free
Qidi Door Latch Rounded by davebpix
...ont door of the qidi printer. put one under each end of the handle on the front door, and the magnets will hold the door closed.
thingiverse
free
QIDI Side Window Clamp by davebpix
...eeded solution. this approach provides four small magnetically retained pieces, each of which captures one corner of the window.
thingiverse
free
Backplate with cable cutout by davebpix
...: https://www.thingiverse.com/thing:2897334
a video showing the teeth installed is at: http://www.youtube.com/watch?v=jlcfjsont4w
thingiverse
free
FT5 713 Glass Corner by davebpix
...ength depends upon your glass bed size. i used a 30mm bolt length.
this design is a remix of a part made by "celphor".
thingiverse
free
Sterilite Lid Clip by davebpix
...ade them longer to cover a larger area, and finally added some traction ridges that made them a bit easier to get on/off the lid.
thingiverse
free
Pi3 backshell with air vents by davebpix
...ores on the pi3 b+ present a widely variable load to the 1000c, and it just cannot cope. so i am looking for some options there.
thingiverse
free
Red Cup Cap by davebpix
... the first 2mm of the lid at 0.16mm layers, and the remaining (lip) areas at 0.3mm layers. this slightly reduces the print time.