Thingiverse
FireFlo v3 by SirQuentin
by Thingiverse
Last crawled date: 3 years, 4 months ago
This is a update of the "FireFlo v2" and a remix of the "DragonFli" frame (yes... with "i"!) and an alternative frame for the Blade NanoQX (also FPV).
Some stuff to watch:
Here is a little video of the very first flight: https://youtu.be/a4SYjWPVkdE
Some general details:
It consists of a topplate and a lowerdeck connected with shock absorbers to undock the flight control + cam and reduce motor vibrations.
It has higher stiffness then the v2
There are different options and predefined strapholders to attach the lipo (on the topdeck or under the lowerdeck)
Antenna protection predrills
More free space to add your own vTx and cam and enough space to place different flight controls (from NanoQx original board to SciSky).
And because it consists of two parts, you can now mix colors yeyyyy!! :D
Some more detailed details:
It fits the original NQX Cam or the additional Spektrum Micro Cam or selfmade cams.
Its available for 7mm and 8.5mm Motors.
You can bend the camera holder up to 20° if you heat it up a bit, but be careful.
Frame size is at ~110 mm diagonal (m2m) and about 9 x 9 cm in length and width.
Frame weighs ~7.3g (depending on the material used).
You will need 3x shock absorbers which can be found here: http://r.ebay.com/Wfjzam
Example Setups that will fit and are tested:
Shock Absorbers:
50g camera gimbal damper rubber anti-vibration shock absorber
(http://r.ebay.com/Wfjzam)
Motormounts:
Motor holders for this frame can be found in the "CopterCustoms"-Group. (http://www.thingiverse.com/thing:1133331)
Antenna Protection:
Just use two cable ties and put them in the provided holes in the lower deck (see screenshots)
Motors 7mm:
micro-motor-warehouse.com: CL-0720-12, CL-0720-14
Standard Hubsan x4 H107L
Motors 8.5mm:
micro-motor-warehouse.com: CL-0820-15, CL-0820-17 Dark Edition
Standard Hubsan x4 H107D, H107C
Flight Control:
(for a proper fit, you should remove the motor plugs and solder the motors directly to the board):
NanoQx Board (MOSFETs need to be replaced when using 8.5mm motors)
NanoQx FPV Board
MicroMWC (MOSFETs need to be replaced when using 8.5mm motors)
SciSky
Cam and vTx:
NanoQx FPV Cam
Spektrum Ultra Micro FPV CAM SPMVA1100
Selfmade like this: http://flitetest.com/articles/diy-micro-5-8ghz-fpv
(but if you get this to fit, its more like a bumblebee then a firefly ;) )
Get the "Bumblebee Backpack" here: http://www.thingiverse.com/thing:1134205
Rotors:
Standard Hubsan x4
Standard Revell Atomium
Energy:
I recommend these for a flight duration of about 5-7min depending on your style and motors: 1s 3,7V 500mAh (http://r.ebay.com/a1v5I0)
Velcro to strap it (10mm)
If you have questions, don't be shy. :)
Some stuff to watch:
Here is a little video of the very first flight: https://youtu.be/a4SYjWPVkdE
Some general details:
It consists of a topplate and a lowerdeck connected with shock absorbers to undock the flight control + cam and reduce motor vibrations.
It has higher stiffness then the v2
There are different options and predefined strapholders to attach the lipo (on the topdeck or under the lowerdeck)
Antenna protection predrills
More free space to add your own vTx and cam and enough space to place different flight controls (from NanoQx original board to SciSky).
And because it consists of two parts, you can now mix colors yeyyyy!! :D
Some more detailed details:
It fits the original NQX Cam or the additional Spektrum Micro Cam or selfmade cams.
Its available for 7mm and 8.5mm Motors.
You can bend the camera holder up to 20° if you heat it up a bit, but be careful.
Frame size is at ~110 mm diagonal (m2m) and about 9 x 9 cm in length and width.
Frame weighs ~7.3g (depending on the material used).
You will need 3x shock absorbers which can be found here: http://r.ebay.com/Wfjzam
Example Setups that will fit and are tested:
Shock Absorbers:
50g camera gimbal damper rubber anti-vibration shock absorber
(http://r.ebay.com/Wfjzam)
Motormounts:
Motor holders for this frame can be found in the "CopterCustoms"-Group. (http://www.thingiverse.com/thing:1133331)
Antenna Protection:
Just use two cable ties and put them in the provided holes in the lower deck (see screenshots)
Motors 7mm:
micro-motor-warehouse.com: CL-0720-12, CL-0720-14
Standard Hubsan x4 H107L
Motors 8.5mm:
micro-motor-warehouse.com: CL-0820-15, CL-0820-17 Dark Edition
Standard Hubsan x4 H107D, H107C
Flight Control:
(for a proper fit, you should remove the motor plugs and solder the motors directly to the board):
NanoQx Board (MOSFETs need to be replaced when using 8.5mm motors)
NanoQx FPV Board
MicroMWC (MOSFETs need to be replaced when using 8.5mm motors)
SciSky
Cam and vTx:
NanoQx FPV Cam
Spektrum Ultra Micro FPV CAM SPMVA1100
Selfmade like this: http://flitetest.com/articles/diy-micro-5-8ghz-fpv
(but if you get this to fit, its more like a bumblebee then a firefly ;) )
Get the "Bumblebee Backpack" here: http://www.thingiverse.com/thing:1134205
Rotors:
Standard Hubsan x4
Standard Revell Atomium
Energy:
I recommend these for a flight duration of about 5-7min depending on your style and motors: 1s 3,7V 500mAh (http://r.ebay.com/a1v5I0)
Velcro to strap it (10mm)
If you have questions, don't be shy. :)
Similar models
thingiverse
free
FireFlo v2 by SirQuentin
...style and motors: 1s 3,7v 500mah (http://r.ebay.com/a1v5i0)
velcro to strap it (10mm)
if you have questions, don't be shy. :)
thingiverse
free
60mm Hubsan hack 8.5mm motors by Simba5
... with 8.5mm motors. the frame weight is only 5 grams.
http://micro-motor-warehouse.com/collections/all-motors/products/cl-0820-17
thingiverse
free
Superlight Microquad Frame for 8.5mm Motors & Nano QX board by geekaz01d
...x fpv board (20mmx20mm bolt pattern) and 8.5mm motors.
http://www.micro-motor-warehouse.com/collections/all/products/cl-0820-15
thingiverse
free
Micro Stealth 100 FPV - Microcopter for 8.5mm Motors, Micro Scisky/Quanum by quadFlyer
...m, vtx and antenna
more information and a video about the micro stealth you find here:http://www.quadflyer.net/tag/micro-stealth/
thingiverse
free
Superlight Microquad Frame for 8.5mm Motors & AlienWii by geekaz01d
...se.com/collections/8mm-custom-builds/products/alien-fc
http://www.micro-motor-warehouse.com/collections/all/products/cl-0820-15
thingiverse
free
Hubsan H107C X4 FPV Racer Frame 110 by Hackbert
...h-600mah
1x hubsan h107c x4 (electronic)
4x m3 nylon screws
1x fpv camera fx797t 3-in-1 super mini 5.8g 40ch av video transmitter
thingiverse
free
Remix for Micro 105 FPV Quadcopter - 8.5mm Motors, Micro Scisky by t4b_
... a version to mount the mini cmos fpv cam 0.008lux for night flights
get the frame from: http://www.thingiverse.com/thing:1221911
thingiverse
free
FPV Micro Quadcopter frame by pascal_da
...on"
fpv cam:eachine tx02
how to separate the fpv camera from the vtx:youtube video
batteries:keenstone 3,7v 500mah 25c lipo
thingiverse
free
DragonFli Nano Quad by Davross
...ng in flexible material rather than purchasing premade balls. unknown/untried model and possibly difficult print due to overhang.
thingiverse
free
8.5mm Motor Mount for Micro Quadcopters (Hubsan X4) by Islemunda
...unt for micro quadcopters (hubsan x4) by islemunda
thingiverse
you can use this motor mount to create your own quadcopter frame.
Sirquentin
thingiverse
free
FireFlo v2 Motormounts by SirQuentin
...nts designed for the fireflo v2 frame. (http://www.thingiverse.com/thing:1133306)
they are available in 6, 7 and 8.5mm.
have fun.
thingiverse
free
CP180 Xiaomi Yi Mount by SirQuentin
...").
it has a strap guide and a nipple to avoid slipping using the tripod thread.
if you have questions, don't be shy. :)
thingiverse
free
Shendrones Corgi RunCam PZ0420M L28 Camera Mount by SirQuentin
...rent simple cam mounts for a runcam pz0420m with 2.8 lens (1/3" sony super had ccd 600 tvl) used on a shendrones corgi frame
thingiverse
free
Shendrones Corgi Polaroid Cube Camera Mount by SirQuentin
...fit better with the elastic material the cube provides! also the hole on the back got a 0.5mm push to the front for a better fit.
thingiverse
free
Shendrones Corgi XT60 Backmount FLEX by SirQuentin
...cting a lipo
now just slide the mount over the bottom plate of the battery tray. because it is flex it should fit and sit tight!
thingiverse
free
FireFlo v2 by SirQuentin
...style and motors: 1s 3,7v 500mah (http://r.ebay.com/a1v5i0)
velcro to strap it (10mm)
if you have questions, don't be shy. :)
thingiverse
free
QX 90 Frame by Evan_C
...i got some inspirations from the fireflo v3 by sirquentin and the orientable camera mount of the eachine falcon...
thingiverse
free
Micro Hex /w camera mount and BBB-FC holder 8.5mm by Puppetx
...camera which has a slight upward tilt, inspired by sirquentin#39;s fireflo series quad. big thanks to brod for the...
thingiverse
free
FireFlo V3 SPRacingF3 8.5mm motor by syahriansyah
...all, i would like to say thank you to sirquentin for this great quad. but, i'm having trouble connecting...
Fireflo
thingiverse
free
FireFlo v2 Motormounts by SirQuentin
...nts designed for the fireflo v2 frame. (http://www.thingiverse.com/thing:1133306)
they are available in 6, 7 and 8.5mm.
have fun.
thingiverse
free
Fireflo v2 nano qx fc mount by Jesse_Blue
...mount by jesse_blue
thingiverse
adaptor to mount the nano qx fc on the fireflo frame with the original plugs/sockets on the pcb.
thingiverse
free
FireFlo v2 VTX backpack codename 'bumblebee' by Jesse_Blue
...tion and mount your vtx on it by using double sided tape.
after printing it you should clean out the holes with a 3mm drill bit.
thingiverse
free
FireFlo with VTX tray, battery fairing by richardbounds
... tie).
motor protectors are from here: http://www.thingiverse.com/thing:1133331
weighs 50g without battery, printed in carbonfil.
thingiverse
free
FireFlo v2 by SirQuentin
...style and motors: 1s 3,7v 500mah (http://r.ebay.com/a1v5i0)
velcro to strap it (10mm)
if you have questions, don't be shy. :)
thingiverse
free
FireFlo V3 SPRacingF3 8.5mm motor by syahriansyah
... battery weighs about 50gr
let me know if anyone needs a 7mm motor version
motor mounts: http://www.thingiverse.com/thing:1133331
thingiverse
free
QX 90 Frame by Evan_C
...a camera modification i got some inspirations from the fireflo v3 by sirquentin, and the orientable camera mount of...
thingiverse
free
MiniQuad 3.7 by MyOwn3Dworld
...this one for the frame and the anti-vibration dampers fireflo v3http://www.thingiverse.com/thing:1152714 so, i decide to draw my design combining...
thingiverse
free
Micro Hex /w camera mount and BBB-FC holder 8.5mm by Puppetx
...which has a slight upward tilt, inspired by sirquentin's fireflo series quad. big thanks to brod for the .scad...
V3
3d_export
$5
Poison-v3
...poison-v3
3dexport
poison-v3
3ddd
$1
Curtain v3
...curtain v3
3ddd
полупрозрачная штора v3
turbosquid
free
v3
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
potato v3
...potato v3
3dexport
turbosquid
$69
Skeletor v3
...royalty free 3d model skeletor v3 for download as ztl and obj on turbosquid: 3d models for games, architecture, videos. (1712713)
turbosquid
$49
Zombie v3
...
royalty free 3d model zombie v3 for download as obj and ztl on turbosquid: 3d models for games, architecture, videos. (1342458)
turbosquid
$2
Bitcoin v3
...
royalty free 3d model bitcoin v3 for download as c4d and prj on turbosquid: 3d models for games, architecture, videos. (1182845)
turbosquid
$29
Turret V3
...alty free 3d model turret v3 for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1217498)
turbosquid
$20
Radiators v3
... free 3d model radiators v3 for download as max, max, and obj on turbosquid: 3d models for games, architecture, videos. (1607437)
turbosquid
$10
Wheel V3S
...e 3d model wheel v3s for download as 3ds, obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1344250)