Fenix PD35 light Diffuser by bmgsackboy

...torchlight. as they had only released the clear diffuser, i'd designed this to get a red diffuser for tactical use. cheers!

...ched to a fenix pd35 to project symbols. symbols are printed separately as a disc. different symbols can be designed and printed.

...s size-offset. our ultimaker 2+ required a scaling of 103% and two minutes of sanding were necessary to accommodate a flush fit.

...lighting of night photography. lights snap solidly into place but has slots for redundant velcro strap to keep flashlight secure.

...ut has slots for redundant velcro straps to keep flashlight secure. requires a m5 bolt as gopro thumb screws wont clear the part.

... monoprice select mini v2 with the settings listed below. i used a raft to ensure the bottom was printed flat on the build plate.

... impacted. this will only work with the fenix pd35 flashlight as it was designed specifically for it. i used tinkercad to design.

...n't help the candling); there was some shrinkage, which required judicious work with a scraper, but it's a snug push-fit.

...diameter, so the light can be pushed down onto the nubbin at the bottom to turn it on and off without removing it from the stand.

...is thingiverse i've made my own difuser for the fenix pd32. i've printed it in glow in the dark. but white wil work too.

...ched to a fenix pd35 to project symbols. symbols are printed separately as a disc. different symbols can be designed and printed.

...torchlight. as they had only released the clear diffuser, i'd designed this to get a red diffuser for tactical use. cheers!

...lighting of night photography. lights snap solidly into place but has slots for redundant velcro strap to keep flashlight secure.

...s size-offset. our ultimaker 2+ required a scaling of 103% and two minutes of sanding were necessary to accommodate a flush fit.

... impacted. this will only work with the fenix pd35 flashlight as it was designed specifically for it. i used tinkercad to design.

...n't help the candling); there was some shrinkage, which required judicious work with a scraper, but it's a snug push-fit.

...ut has slots for redundant velcro straps to keep flashlight secure. requires a m5 bolt as gopro thumb screws wont clear the part.

...(https://www.amazon.com/peteast-retractable-tangle-free-lightweight-one-handed/dp/b07d6qs2bs) and fenix pd35 flashlight which has a clip (https://www.fenix-store.com/fenix-pd35ac-led-flashlight-tactical-edition/). since the flashlight has a clip, i designed this...

...fenix pd32 stand thingiverse this is a stand for the fenix pd32 torch.

...pa thingiverse garmin fenix 3 hr bike mount this design is compatible with no chqnge with garmin fenix 5, fenix 5x plus, fenix 6

...fenix e21 wall mount thingiverse simple wallmount for me fenix e21 flashlight.

...fenix hm61r helmet mount by tmosiolek thingiverse fenix hm61r helmet mount

...fenix ld02 grip and stand by amjj188 thingiverse tactical grip and stand for fenix ld02 flashlight.

...protective cap for the garmin fenix 5, fenix 5x. it fits so perfectly that it holds without glue. printed out with an sla printer

...saint seiya fenix box by francqueli thingiverse saint seiya armadura caja fenix ideales para llavero

...ched to a fenix pd35 to project symbols. symbols are printed separately as a disc. different symbols can be designed and printed.

...garmin fenix 6 quickfit bike mount thingiverse adapt for garmin fenix 6

...fenix 5x bezel bumper by jburchm1 thingiverse printable bumper to fit your fenix 5x and protect the bezel from scratches.

...diffused downstem thingiverse printable diffused downstem for bong. length 145mm.

...rse this is a diffuser for atm bz3,you have to screw it to your rear shoch mount... upgraded version to fit with lay down shocks

...ed for my enclosure. 20 cm lenght. with holes for screws. printed with transparent petg. cornesr must be printed with perimeters.

...flash diffuser by usinafablab thingiverse flash diffuser

...light diffuser by danfpv thingiverse light diffuser for ulti steel.

...led diffuser by coalman321 thingiverse diffuses light from leds.

...hookah diffuser by kasame29 thingiverse shisha hookah diffuser for 18.3mm pipe

...s into the water. this one was made for an egyptian 3 pipe hub of diameter 14mm. happy smoking! *to be printed the flat side down

...emisar d4 diffuser thingiverse a simple diffuser for the emisar d4. it should work on either the first or second generation.

...led-diffuser by migi82 thingiverse led-diffuser for 5mm and 3mm standard led tight version and normal version

...light bulb light by rubyrox544 thingiverse it is a light that uses a led light which can light up a room.

...p-light night-light/mood-light here's a link to that project.http://www.instructables.com/id/beautiful-tap-light-night-light/

...bike light thingiverse bike light

...light bulb thingiverse light bulb

...snowman light thingiverse snowman light

...minecraft light thingiverse minecraft light

...t light) by northriver thingiverse a 3d printed cover for a usb light stick. it could be used as a night light or reading light?

...road light, street light by silvanus321 thingiverse use the hair dryer to curve the pole. print in 120% to fit the led light.

...mag light task light by khiebert thingiverse articulated arm for mini mag-light for those jobs that require three hands

...he light from reflecting off of the tv. two of these per light seems to do the trick. i just used tape to attach them together.