Thingiverse
Face Shield Variant3 by dwboyd63
by Thingiverse
Last crawled date: 4 years, 2 months ago
Designed this to use standard clear PCV 8 1/2"x11" binder sheets. 3 Hole Punch and a couple rounded corners is all that's needed. Simple to print, uses office supply clear PVC 8 1/2"x11" binder sheets for spiral bound reports, and rubber bands, since elastic is in short supply in many places. I am printing 10-12/ day in my spare time. More variations to come...
Similar models
thingiverse
free
Hido Face Shield by 3DVolunteer
... clear pvc 8 1/2" x 11" cover sheet.
use a 3 hole punch to make mounting holes.
use elastic string or band for strap.
thingiverse
free
Bed Sheet Clip by cooasty
...nd. use of small binder clips
can make things easier where access is limited.
3/4" wide x 3/8" (19mm) deep binder clips
thingiverse
free
Face Shield Covid Corona 3 Hole by dsaundersflexco
...ic with standard 3 hole punch spacing. pin configurations allow for printing with no support structure, either single or stacked.
thingiverse
free
Laser Cut Face Shield (3-Hole Punch w/ Headband) by EagleTechRob
...standard width)
1-to-3 rubber bands (add bands to size)
equipment:
laser cutter
heat gun (for heating up and installing headband)
thingiverse
free
Capshield Ball Cap Face Shield PPE by gbflyer
... ea. 6-32 x 5/8" long screws and 5 pieces of 1/8" id x 1/4" od vinyl tubing 5/8" long to finish the assembly.
thingiverse
free
Malyan M150 Acrylic Bed Holder Clip by alexi3d
...ar the print head.
they are easy to remove and re-insert, you may have to file them down a tiny bit but it depends on your setup.
thingiverse
free
Candy Dispenser by Mason_Basinger1
...inger1
thingiverse
8" x 8" x 1'5" w/ 8 1/2 x 8 1/2" x 1"
attention: this will take multiple prints.
thingiverse
free
Lyman Paper Padding Press by hlyman
...ea #6 x 1/2" flat head sheet metal screws mdf panel screws)
4 ea #6 x 1/2" round head sheet metal screws (dowel screws)
thingiverse
free
Reusable Face Shield Frame by CMPresby
....5"x11", the center post is offset, this is normal and the design intent so the transparency sits even across the face.
thingiverse
free
Lulzbot Mini enclosure - solvent welded by amstapel
...aps
-optimized finger joints for friction fit and solvent weld
laser cutter settings used:
-speed: 8
-power: 95
-corner power: 85
Shield
thingiverse
free
Shield
...shield
thingiverse
shield designed for 28mm scale.
thingiverse
free
Shield
...shield
thingiverse
draft of a shield for action figures. work in progress.
thingiverse
free
Eye Shield/face Shield by surfer03
...
thingiverse
this is a piece to put deroyal eye shields because hospitals have the shields but not the bands to hold the shields
thingiverse
free
Sun Shield For nVIDIA SHIELD by Digson
...sun shield for nvidia shield by digson
thingiverse
sun protection for my nvidia shield k1.
thingiverse
free
Shield by lkg218
...shield by lkg218
thingiverse
shield
thingiverse
free
shield by keihoag
...shield by keihoag
thingiverse
a shield
thingiverse
free
Shield by Albialva
...shield by albialva
thingiverse
shield
thingiverse
free
Nerf Shield
...nerf shield
thingiverse
nerf shield mount. use a trasparent ferrero rocher packaging as a shield.
thingiverse
free
Viking Shield
...viking shield
thingiverse
viking shield
thingiverse
free
Shield by lkg218
...shield by lkg218
thingiverse
knotted shield
Face
thingiverse
free
face
...face
thingiverse
my first face
thingiverse
free
Face
...face
thingiverse
just a simple face i made in like 5 minutes.
thingiverse
free
Face Toucher
...face toucher
thingiverse
face toucher, for touching faces. in a time when touching your face is bad, here is a thing for you.
thingiverse
free
FACE by nagato
...face by nagato
thingiverse
face
thingiverse
free
face by angel19000
...face by angel19000
thingiverse
face
thingiverse
free
Face by Iqra
...face by iqra
thingiverse
face
thingiverse
free
Face by dcgstudent
...face by dcgstudent
thingiverse
a face
thingiverse
free
face by nagato
...face by nagato
thingiverse
face
thingiverse
free
FACE by nagato
...face by nagato
thingiverse
face
thingiverse
free
FACE by nagato
...face by nagato
thingiverse
face