Thingiverse
Extrusion Flowrate Calculator by LuckyPants
by Thingiverse
Last crawled date: 3 years ago
With the Google sheet open, from the File menu there is the option to make a copy in your GDrive. This will give you your own, editable copy
This is a Google Sheet to assist in choosing layer heights and print speeds based on nozzle size and a maximum flow rate.
Hot end/extruder combos can only flow so much material before they start skipping/etc. I ran into this with my Flashforge Creator Pro when trying to extrude thick layers @ 90mmps with a .6mm nozzle.
I made this Sheet to assist in figuring out:
1)For a given nozzle size and layer height, what is the max feedrate I can run while staying withing the set flowrate?
2)For a given nozzle size and feedrate, what is the max layer height I can run while staying within the set flowrate?
There are 3 sections in it:
1)Quick flowrate calc - plug in your nozzle size, layer height, and print speed to get the flowrate.
2)Solve for print speed - plug in your target flowrate. Max print speed will be calculated based on desired nozzle sizes and layer heights. Change these as you see fit.
3)Solve for layer height - plug in your target flowrate. Max layer height will be calculated based on desired nozzle sizes and feedrates. (Note max layer height is limited to 1.5x layer width).
Scour the internet to figure out what the generally accepted flowrate is for your hot end, or experiment. I've setted around 12 mm3/sec for my Creator Pro with all metal Microswiss hotend.
https://drive.google.com/open?id=19FvxnxfEBbd4TxkqHSfrOOUX7gwcBX5Uawkq1ag1LgE
This is a Google Sheet to assist in choosing layer heights and print speeds based on nozzle size and a maximum flow rate.
Hot end/extruder combos can only flow so much material before they start skipping/etc. I ran into this with my Flashforge Creator Pro when trying to extrude thick layers @ 90mmps with a .6mm nozzle.
I made this Sheet to assist in figuring out:
1)For a given nozzle size and layer height, what is the max feedrate I can run while staying withing the set flowrate?
2)For a given nozzle size and feedrate, what is the max layer height I can run while staying within the set flowrate?
There are 3 sections in it:
1)Quick flowrate calc - plug in your nozzle size, layer height, and print speed to get the flowrate.
2)Solve for print speed - plug in your target flowrate. Max print speed will be calculated based on desired nozzle sizes and layer heights. Change these as you see fit.
3)Solve for layer height - plug in your target flowrate. Max layer height will be calculated based on desired nozzle sizes and feedrates. (Note max layer height is limited to 1.5x layer width).
Scour the internet to figure out what the generally accepted flowrate is for your hot end, or experiment. I've setted around 12 mm3/sec for my Creator Pro with all metal Microswiss hotend.
https://drive.google.com/open?id=19FvxnxfEBbd4TxkqHSfrOOUX7gwcBX5Uawkq1ag1LgE
Similar models
thingiverse
free
Flow Calibration Cube by Xarnos_Black
...rrent flow by the value e.g. if flow is 109% and you get a new value of 0.98 then 109 x 0.98 and you get 106.8% as your new flow.
thingiverse
free
Flow Rate Tower Calculator for Vase Mode
....com/2019/10/26/calculate-max-flow-rate-and-max-speed/
also on my youtube channel: https://youtu.be/wbcpne3bkqg
thanks
callum
:-]
thingiverse
free
Lion by LynnBao
...nt it by the following parameter
object infill: 10%
layer height: 0.27mm
shells:1
feedrate:40
travel feedrate :55
temperature:220
grabcad
free
Convergent nozzle; to achieve high speed airflow.
...airflow.
grabcad
this was a nozzle designed to achieve high speed flow for a given blower spec. manufacturing drawings included.
thingiverse
free
Daisy Flower Vase by Mazuir
...nfill, and your desired perimeters. i suggest going with 8 bottom layers and 4 perimeters. i did the print in 0.2mm layer height.
thingiverse
free
Flow Calibration Cube by humebeam
...available for easy editing.
if you enjoy this or any of my other designs, a small donation is not needed but welcome. thanks! :)
thingiverse
free
Chaos Trim Airbrush Stencil by Stealthizer
...chaos trim with an airbrush. to use this kind of stencils i print this sheet with only 3-4 layers max. best results at 0.2 nozzle
thingiverse
free
Generic Heraldry Airbrush Template by Stealthizer
...dry shapes with an airbrush. to use this kind of stencils i print this sheet with only 3-4 layers max. best results at 0.2 nozzle
thingiverse
free
Chaos Stars Airbrush Stencil by Stealthizer
...haos icons with an airbrush. to use this kind of stencils i print this sheet with only 3-4 layers max. best results at 0.2 nozzle
thingiverse
free
Runical Transporters Airbrush Stencil by Stealthizer
...rters logo with an airbrush. to use this kind of stencils i print this sheet with only 3-4 layers max. best results at 0.2 nozzle
Luckypants
thingiverse
free
IoT Fingerprint Scanner w/ OLED by LuckyPants
...ct surfaces ~75%.
fusion360 source file included for tinkering.
arduino sketch: https://github.com/luckypants123/fingerprint-mqtt
thingiverse
free
Dimensional thermal test jig (for annealing) by punkgeek
...is a companion for the dimensional calibration tool by luckypants it allows you to place up to 4 of...
thingiverse
free
Geeetech G2s Upgrades by LuckyPants
...he printer seems much smoother. if you plan to do these upgrades, let me know and i'll upload the correct configuration file.
thingiverse
free
Shrinkage calculation object by LuckyPants
...le sheet shown in the images:https://docs.google.com/spreadsheets/d/10cfmuad_anwwsmppas5jzbknkithyhfe8xmzlksgmfo/edit?usp=sharing
thingiverse
free
Dimensional Calibration Tool v9 by LuckyPants
...iterations of this, but in my case once was good enough to get me to less than 100um over the 150mm part, which i was happy with.
thingiverse
free
Geeetech G2s Upgrades v2 by LuckyPants
...ted led’s for overall interior lighting.
b. effector mounted led’s for part lighting.
c. led brightness controllable by m code.
thingiverse
free
Scaling and Horizontal Compensation Calibration by jlambier
...also added a series of small holes that can be tested with drill bits to see how small of a hole that i could produce accurately.
thingiverse
free
Flashforge Creator Pro Bed Level code by LuckyPants
...00mm thick) it will be wrong!
2.the attached calibration cube is just here because thingiverse won't let me just upload code.
Flowrate
thingiverse
free
RaceWhoop by Freezillion
...points temp 242° bed 60° with brim and pva flowrate 105 infill and 110 wall print infill first 20mm...
thingiverse
free
5015 fan silencer by FullPlasticScientist
...-2.7mm shorter for tight installation requirements ----future work---- build flowrate pressure and acoustic testrig. using arduino, custom printed venturi...
thingiverse
free
Vented funnel (vase mode) by mtlux
...design allows for air venting. that means high liquid flowrate and less chances of funnel overflowing (can't make it...
thingiverse
free
E3(Pro) Glass Build Plate Corner Caps by kai_to_makes
...;setup jerk m220 s100 ;reset feedrate m221 s100 ;reset flowrate g28 ;home g92 e0 ;reset extruder g1 z2.2 f3000...
thingiverse
free
Flow Calibration Cube by Xarnos_Black
...calculate new flow rate for a print with a flowrate that is not 100% just do the same calculation...
thingiverse
free
Centrifugal Pump by Ulf_vom_Mond
...until the flow stopped without the pump breaking. the flowrate wasn't as wet to measure and resulted in 7.5...
thingiverse
free
20mm cube for walls test by pyroevil
...of your extruder correctly , you can fine-tune the flowrate for each filament pool with this cube. the example...
thingiverse
free
Calibration Cube 30n15mm by Webberen
...trusty old #wanhao duplicator i3 it helps with calibrating: -flowrate (toplayer) -steps/mm xyz -jerk and accelaration i hope you...
thingiverse
free
Creality Ender 3 - Silence & Quality Mod by petrzmax
...http://bit.ly/2ovbu5z if you don't know how to calibrate your flowrate check this guide: http://bit.ly/2v2uxef if you want to make...
thingiverse
free
Micro SD Card threaded Box by Drop-d
...print with 0.1mm resolution! you might want to reduce flowrate a little for a better...
Calculator
cg_studio
$29
Calculator3d model
... model
cgstudio
.3ds .c4d .dae .fbx .obj - calculator 3d model, royalty free license available, instant download after purchase.
3d_ocean
$29
100 Mono Icons Mixed Pack
...ns and 34.115 points, calculated in cinema 4d r15. render system and materials are ready. c4d and other file formats not smoot...
3d_ocean
$15
Office Supplies Pack
...office supplies pack 3docean calculator cubicle dispenser eraser markers office paper pencils pens scissors...
3d_ocean
$12
Casio Scientific Calculator
...ginaly modeled in rhino4 3d and rendered with vray. in the package are included high resolution textures, making this model id...
3d_ocean
$5
Abacus
...abacus 3docean 3d 3ds abacus c4d calculator children counting education learn math mathmatics max model office...
3d_ocean
$7
Infographics 3D Models in 3 Styles Part 3
...t for you. please check video and item support tab for usage. the file has 18401 polygons and 16877 points, calculated in cine...
3d_ocean
$6
Calculator
...ted in cinema 4d with vray. all needed materials and images included in the download file. also there is two format included (...
3d_ocean
$7
Infographics 3D Models in 2 Styles
...t for you. please check video for usage. the file has 5994 polygons and 5866 points, calculated in cinema 4d r15. render syste...
3d_ocean
$19
3D Gears Human Head Shaped
...cle styles. the file has total 115.939 polygons and 112.320 points, calculated in cinema 4d r15. render system and materials a...
3d_ocean
$6
Infographics 3D Models in 2 Styles Part 2
...t for you. please check video and item support tab for usage. the file has 15524 polygons and 14489 points, calculated in cine...
Extrusion
3d_export
$300
melt-blown fabric extrusion molding machine
...an email to me.<br>designed with solidworks 2017, render with photoview 360<br>**************************************
3d_export
$10
glue injection machine
...injection technology. the ordinary glue injection machine is screw extrusion type, and its instantaneous pressure can reach more than...
3d_export
$7
wireline
...from the ceiling, the cable holds a ribbed glass extrusion containing an led light source. the lamp plays on...
3d_export
$5
one-eyed scary virus
...cinema, the body relief is formed by the standard extrusion noise. the eye texture is...
3d_export
$5
Spaceship - Galaxy Crusher
...with a more ominous twist. it has lots of extrusion and cubes and comes with a whopping 4k texture,...
3d_export
free
30 x 30 extrusion
... x 30 x 40.sldprt<br>30 x 30 x 50.sldprt<br>30 x 30 x 606.sldprt<br>the sketch.sldprt<br>30 x 30 x 40.stl
3d_export
$1000
bead triangle adhesive laminating machine
...a triangular rubber head with the shape required for extrusion the rear end of the extruder is also provided...
3d_export
$20
1600 Meltblown cloth production line set drawing CAD
...width of 1600mm. the steel structure frame, feeding host, extrusion screw, heating system, screen changer, metering pump, melting it...
3d_export
$20
GE TF34 Fan Blade and Nose Cone
...and appropriately sized fillet features are provided.<br>also, a threaded extrusion profile is provided on the fan blade component and...
turbosquid
free
aluminum extrusion profiles
...free 3d model aluminum extrusion profiles for download as max on turbosquid: 3d models for games, architecture, videos. (1381707)