Thingiverse
Ender 5 Core XY with Linear Rails MK2 by BoothyBoothy
by Thingiverse
Last crawled date: 3 years ago
Update 06\04\21
Uploaded a revised Mounting Plate for the V1.5 Orbiter Extruder with a reinforced\ more robust WM Upstand.
Update 31\03\21
Based On feedback by TheOML I have uploaded a revised BL Touch Bracket which is 5mm longer. This part is untested. It will require a small amount of support to print effectively. WIP.
Update 31\03\21
Uploaded a revised Mounting Plate and Adapter Plate for the V1.5 Orbiter Extruder. The Extruder hole Mounts slightly conflict with the existing Duct Base mounts so I have had to design an additional adapter plate to overcome this short term. Long term I will design a specific mount for this but this will mean printing a new Duct Base to suit. I have tested this arrangement on another prototype printer but not specifically the MK2 conversion so please treat this as WIP.
Update 25\03\21
I have revised the Duct Base with a side access slot to allow the easier removal and insertion of a Bowden tube clip & collar. I have installed and tested this and insertion and removal are relatively easy with a small terminal screwdriver or similar tool. I had to slightly move the WM clamp fixing centre so I have also updated that part has well. Revised duct base step file also included. Revised the rear fan cable tray to insert the RH fan cable more easily. Minor design tweaks to improve print quality
This is my second Core XY conversion kit for the Ender 5 with Linear rails.
Test Print Video here: https://www.youtube.com/watch?v=H8vL2GeMYMQ
Previous version here: https://www.thingiverse.com/thing:4650517
As per the previous version a big shout out to Scott3D for his fabulous work on the Hypercube Evo which I have taken the belt tensioner detail from and a massive thanks to barnabyQ for his Ender 5 Pro 3D model over on Grabcad. This made things so much easier.
The major difference with this version is that I have placed the hot end assembly closer to the linear rails so there is much smaller cantilever from the nozzle to the linear rail. This should result in reduced inertia. The hot end assembly in this version is also very bespoke reducing the size. The belts are also immediately below the linear rails which should also help speed of printing.
Other Improvements:
The Linear rails mounts although additional parts allow for much direct easy mounting than mounting directly to the extrusions.
Includes an optional Extrusion motor mount to it to be sited in the middle of the side frame. In addition to making it much easier to change filament as opposed to the rear of the frame, being centrally mounted allows the bowden tube to be slightly reduced which is always a good thing.
Includes a set of vertical wire management ducts to tidy up the messy stock cabling. Designed in two parts to allow printing on the Ender 5 build plate. There is also a second upper duct which can be used with the stock metal motor mounting plate if preferred
Optional Direct Drive Stock Extruder plate.
I have designed an offset fan shroud for a V6 compatible heat sink which allows a BL Touch to be mounted at the front but still mostly clear of the front facing 3010 heat sink fan. There are also alternative cover plates for without any sensor and one with an offset down stand potentially for a LED light source and wiring.
The firmware changes were relatively simple, there are only a few comments to tweak. I did however have to invert the direction of the X & Y motors. Uncommenting Z_CLEARANCE_BETWEEN_PROBES & Z_HOMING_HEIGHT stopped the Z axis from trying to drop to clear when homing. I have included my config file within the upload for reference.
The conversion will easily allow for the stock 220 x220 build volume and allows for the full 235 x235 dependent on duct design. I have not yet designed a 5015 fan duct set.
I have since attached a Optical End Stop to the X axis to tidy up all the cables. I had to extend a 1 metre cable to do this and provide a separate power feed to a spare 5v pin on my BTT E3 Mini board.
I have also remixed a fixed variant of my Slim Display Housing to sit inboard of the Ender 5 Frame here: https://www.thingiverse.com/thing:4650597
I have uploaded step files for the Duct Base, Bowden Tool Plate and XY joiners for customisation.
Installation
1.I have classed this has WIP because I have not yet been able to provide a detailed installation guide. I have however included a high res annotated screen grabs for the assembly and a sample BOM for the parts in the upload to get you started. Please comment or message me for further technical information.
2.The Bill of Materials is only indicative and the relevant parts could be purchased much more cost effectively at the likes of Aliexpress. I had most of the parts in stock so personally this conversation cost very little.
3.The forward idlers are created by removing the front to M5 2020 frame fixings and replace them with a 80mm threaded bar. This is a very simple but strong foundation for the front idlers. I have not seen any side effect in rigidity terms but you may want to attach some additional corner brackets if concerned about the rigidity of the frame overall.
4.With XY joiners there is no perfect print orientation due to the stress by the belts on both axis. I have therefore included 4 x 40 mm long M3 tie bolts which fasten across the print grain to help reduce any potential delamination of the layers. I have found out of experience any many prototypes with my HEVO that this little mechanical indulgence is well worth it in terms of longevity.
Printing
1.All parts print without supports except for the Bowden Tool Plate, which may require some custom supports under the wire management port if it is printed vertically as uploaded. The tool plate will print fine horizontally just not quite the same surface finish. There are some sacrificial layers across some holes to help bridging which will require cleaning through.
2.Due to the belt tension applied these parts need to be printed quite strongly. Therefore I have printed all parts with at least 30% infill and 3 layers. I would suggest all parts near to the hot end and bed should be printed in PETG whilst others will be fine in PLA if sufficient layers and perimeters are adopted. The black parts are ABS, the ABS parts were printed with no cooling and a 10 layer brim to reduce warping.
3.Printed with Amazon Basics Yellow PETG @2.5 layer height, 40 mms on various
printers. Black parts Verbatim Black ABS, 2 layer brim, no part Cooling (except bridging), 50% infill, 3 perimeters.
Quick Tips
1.The Belt Tensioner assembly is much easier to put together with the printer on its front and therefore facing the parts laid flat. Leave a reasonable amount of spare belt for tensioning before trimming the belt.
2.Use a M3 tap to clear all the plastic from the thread inserts prior to assembly, it makes life much easier.
3.The thermal inserts I have used have an average OD of 5.2 mm. Therefore I use a 4.7mm insertion hole. Smaller inserts may require a smaller hole size. They are listed in the BOM.
Uploaded a revised Mounting Plate for the V1.5 Orbiter Extruder with a reinforced\ more robust WM Upstand.
Update 31\03\21
Based On feedback by TheOML I have uploaded a revised BL Touch Bracket which is 5mm longer. This part is untested. It will require a small amount of support to print effectively. WIP.
Update 31\03\21
Uploaded a revised Mounting Plate and Adapter Plate for the V1.5 Orbiter Extruder. The Extruder hole Mounts slightly conflict with the existing Duct Base mounts so I have had to design an additional adapter plate to overcome this short term. Long term I will design a specific mount for this but this will mean printing a new Duct Base to suit. I have tested this arrangement on another prototype printer but not specifically the MK2 conversion so please treat this as WIP.
Update 25\03\21
I have revised the Duct Base with a side access slot to allow the easier removal and insertion of a Bowden tube clip & collar. I have installed and tested this and insertion and removal are relatively easy with a small terminal screwdriver or similar tool. I had to slightly move the WM clamp fixing centre so I have also updated that part has well. Revised duct base step file also included. Revised the rear fan cable tray to insert the RH fan cable more easily. Minor design tweaks to improve print quality
This is my second Core XY conversion kit for the Ender 5 with Linear rails.
Test Print Video here: https://www.youtube.com/watch?v=H8vL2GeMYMQ
Previous version here: https://www.thingiverse.com/thing:4650517
As per the previous version a big shout out to Scott3D for his fabulous work on the Hypercube Evo which I have taken the belt tensioner detail from and a massive thanks to barnabyQ for his Ender 5 Pro 3D model over on Grabcad. This made things so much easier.
The major difference with this version is that I have placed the hot end assembly closer to the linear rails so there is much smaller cantilever from the nozzle to the linear rail. This should result in reduced inertia. The hot end assembly in this version is also very bespoke reducing the size. The belts are also immediately below the linear rails which should also help speed of printing.
Other Improvements:
The Linear rails mounts although additional parts allow for much direct easy mounting than mounting directly to the extrusions.
Includes an optional Extrusion motor mount to it to be sited in the middle of the side frame. In addition to making it much easier to change filament as opposed to the rear of the frame, being centrally mounted allows the bowden tube to be slightly reduced which is always a good thing.
Includes a set of vertical wire management ducts to tidy up the messy stock cabling. Designed in two parts to allow printing on the Ender 5 build plate. There is also a second upper duct which can be used with the stock metal motor mounting plate if preferred
Optional Direct Drive Stock Extruder plate.
I have designed an offset fan shroud for a V6 compatible heat sink which allows a BL Touch to be mounted at the front but still mostly clear of the front facing 3010 heat sink fan. There are also alternative cover plates for without any sensor and one with an offset down stand potentially for a LED light source and wiring.
The firmware changes were relatively simple, there are only a few comments to tweak. I did however have to invert the direction of the X & Y motors. Uncommenting Z_CLEARANCE_BETWEEN_PROBES & Z_HOMING_HEIGHT stopped the Z axis from trying to drop to clear when homing. I have included my config file within the upload for reference.
The conversion will easily allow for the stock 220 x220 build volume and allows for the full 235 x235 dependent on duct design. I have not yet designed a 5015 fan duct set.
I have since attached a Optical End Stop to the X axis to tidy up all the cables. I had to extend a 1 metre cable to do this and provide a separate power feed to a spare 5v pin on my BTT E3 Mini board.
I have also remixed a fixed variant of my Slim Display Housing to sit inboard of the Ender 5 Frame here: https://www.thingiverse.com/thing:4650597
I have uploaded step files for the Duct Base, Bowden Tool Plate and XY joiners for customisation.
Installation
1.I have classed this has WIP because I have not yet been able to provide a detailed installation guide. I have however included a high res annotated screen grabs for the assembly and a sample BOM for the parts in the upload to get you started. Please comment or message me for further technical information.
2.The Bill of Materials is only indicative and the relevant parts could be purchased much more cost effectively at the likes of Aliexpress. I had most of the parts in stock so personally this conversation cost very little.
3.The forward idlers are created by removing the front to M5 2020 frame fixings and replace them with a 80mm threaded bar. This is a very simple but strong foundation for the front idlers. I have not seen any side effect in rigidity terms but you may want to attach some additional corner brackets if concerned about the rigidity of the frame overall.
4.With XY joiners there is no perfect print orientation due to the stress by the belts on both axis. I have therefore included 4 x 40 mm long M3 tie bolts which fasten across the print grain to help reduce any potential delamination of the layers. I have found out of experience any many prototypes with my HEVO that this little mechanical indulgence is well worth it in terms of longevity.
Printing
1.All parts print without supports except for the Bowden Tool Plate, which may require some custom supports under the wire management port if it is printed vertically as uploaded. The tool plate will print fine horizontally just not quite the same surface finish. There are some sacrificial layers across some holes to help bridging which will require cleaning through.
2.Due to the belt tension applied these parts need to be printed quite strongly. Therefore I have printed all parts with at least 30% infill and 3 layers. I would suggest all parts near to the hot end and bed should be printed in PETG whilst others will be fine in PLA if sufficient layers and perimeters are adopted. The black parts are ABS, the ABS parts were printed with no cooling and a 10 layer brim to reduce warping.
3.Printed with Amazon Basics Yellow PETG @2.5 layer height, 40 mms on various
printers. Black parts Verbatim Black ABS, 2 layer brim, no part Cooling (except bridging), 50% infill, 3 perimeters.
Quick Tips
1.The Belt Tensioner assembly is much easier to put together with the printer on its front and therefore facing the parts laid flat. Leave a reasonable amount of spare belt for tensioning before trimming the belt.
2.Use a M3 tap to clear all the plastic from the thread inserts prior to assembly, it makes life much easier.
3.The thermal inserts I have used have an average OD of 5.2 mm. Therefore I use a 4.7mm insertion hole. Smaller inserts may require a smaller hole size. They are listed in the BOM.
Similar models
thingiverse
free
Hypercube Evolution XY Joiner with Extended Bolt Fixings by BoothyBoothy
...o. i printed these parts at quite a high temp, 240 c with a low retraction rate to minimise delamination of layers when printing.
thingiverse
free
Ender 5 Core XY with Linear Rails by BoothyBoothy
...may reduce the print quality.
test video here: https://youtu.be/guwfuaic5nc
update 02_01_21:
uploaded forward lh\rh idler guards.
thingiverse
free
Ender 5+ 2020 mount for bowden and cable guide by falcon14141
... part can also be used to hold the stock ender5+ cable guide, if having the cables climbing z by the right side and not the back.
thingiverse
free
Ender 5 plus linear rails + core-xy by MPH2
...tures to go along with this. also instructions somewhat.
stl's
front bearing plate
gantry plate
extruder plate -- coming soon
thingiverse
free
Ender 3 Hero Me 5 no Y offset for linear rail and direct drive BMG by seanauff
...it might be wise to just print the first few layers before the entire thing to check if the mount points line up with your setup.
thingiverse
free
Da Vinci 1.0 E3D V6 drop in remix by NAK3DDesigns
...orners of my print bed). i have not yet tested this in my printer.
please see the original builds for further installation notes
thingiverse
free
Hypercube Evolution Nut Remix by Beezen
...e belt tensioner)
extruder mount (1 with sensor and 1 without sensor)
in case i forgot a part, please write it in the comments :)
thingiverse
free
Sapphire Pro BMG + Volcano Mount and Duct by bentwenty
...ld also work on the sapphire plus and sapphire s, although i have only tested on my sapphire pro.
i'm keen to see any makes!
thingiverse
free
Ender 5 Double 5015 Fan Shroud and Ducts by Andrea_Botti
...and is removable at any time if necessary.
i know it's not the best solution but this keeps the whole thing light and simple.
thingiverse
free
linear rail direct drive bmg mount for ender 3
...opposite of the x motor to reduce belt tension and allow the adjustment of the belt via separate tensioner
update:
x = 28
y = -19
Boothyboothy
thingiverse
free
Bed Thumbwheel with M3 retention by BoothyBoothy
...bed thumbwheel with m3 retention by boothyboothy
thingiverse
yet another thumb wheel for a m3 bolt.
thingiverse
free
Simple Cable Hoops for the Zonestar P802QR2 by BoothyBoothy
...erse
simple thing to provide cables hoops above the motherboard to help tidy the various cables running vertically up the frame.
thingiverse
free
Filament Guides for the Zonestar P802QR2 by BoothyBoothy
...e the motherboard.
collection of all my upgrades for the zonestar at the following link:https://www.thingiverse.com/thing:2936870
thingiverse
free
PSU Cover for Zonestar P802QR2 by BoothyBoothy
...e psu more firmly.
collection of all my upgrades for the zonestar at the following link:https://www.thingiverse.com/thing:2936870
thingiverse
free
Picture frame for Mini Lithophane light Box - Simple by BoothyBoothy
...ht box from amazon
light box link: https://www.amazon.co.uk/gp/product/b0767lgtzm/ref=oh_aui_search_detailpage?ie=utf8&psc=1
thingiverse
free
Fire TV (2017) Simple Mounting Bracket by BoothyBoothy
...perhaps some cable management considered in the next version !
update:03_04_19 included hoop for cable tie to aid wire management
thingiverse
free
Tripod Bubble Level by BoothyBoothy
...the bubble vials on amazon:-
link: https://www.amazon.co.uk/gp/product/b01ir5ioru/ref=oh_aui_search_detailpage?ie=utf8&psc=1
thingiverse
free
Open Picture Frame for Lithophane Images by BoothyBoothy
...ck.
support\stand components are bonded to rear of frame. registration mark included within model to help align support brackets.
thingiverse
free
Bird Spikes for a Curved Ridge Tile by BoothyBoothy
...int. remodelled in fusion 360.
due to the curved base plate the thing is best printed with a raft and support to the build plate.
thingiverse
free
Wall Bracket for Nespresso Vertuo Capsules by BoothyBoothy
...ngs which can be used for bolting tiles together i have also included some countersunk holes for direct fixing to a door or wall.
Xy
3ddd
$1
Вешалка напольная XY-027
...а штанги: 171 см
диаметр основания: 38 смhttp://mebelshopos.ru/aksessuary-ofisnye/veshalka-napolnaya-xy-027-detail.html
turbosquid
$9
XY Rectangular Dining Table
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
holly hunt xy bench
...eight: 17.75 in
width: 45 in, 26 in
depth: 18 in
больше превьюhttps://www.behance.net/gallery/24983999/bench-3d-model?
turbosquid
$8
Xy fine tuning handle adjusts the module
...odule for download as 3ds, max, ige, obj, fbx, stl, and sldas on turbosquid: 3d models for games, architecture, videos. (1331394)
3ddd
$1
pillows bed 2
...pillows bed 2 3ddd подушка , круглая dimensions: xy ...
3ddd
$1
Honeycomb Floor
...паркет parquet with metalic honeycomb floor demensions 500x500 cm xy multitexture +...
3d_export
$7
positioning screw mechanism
...and lead screw, constitute a double displacement adjustable mechanism, xy axis double position adjustable positioning.<br>**************************************<br>files format contains<br>-solidworks 2017<br>-step<br>-iges<br>- and...
3d_export
$9
positioning mechanism of heavy-duty platform
...activity -- ball mechanism activity ---- drive heavy load xy axis movement -- positioning completed<br>**************************************<br>files format contains<br>-solidworks 2017<br>-step<br>-iges<br>- and...
3d_export
$180
optical fiber laser marking machines assembly
...fiber laser marking machine<br>automatic loading and unloading laser marking machine<br>xy platform adjustable laser marking machine<br>laser marking machine used with...
thingiverse
free
XY ROBOT by ymtlab
...xy robot by ymtlab
thingiverse
xy robot
Mk2
turbosquid
$4
Mk2
...
royalty free 3d model mk2 for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1305687)
turbosquid
$9
Mk2 Grenade
...osquid
royalty free 3d model mk2 grenade for download as fbx on turbosquid: 3d models for games, architecture, videos. (1175401)
turbosquid
$4
Mk2 Grenade
...quid
royalty free 3d model mk2 grenade for download as blend on turbosquid: 3d models for games, architecture, videos. (1228888)
turbosquid
$2
mk2 Grenade
...osquid
royalty free 3d model mk2 grenade for download as fbx on turbosquid: 3d models for games, architecture, videos. (1329079)
turbosquid
$2
GRENADE MK2
...osquid
royalty free 3d model grenade mk2 for download as fbx on turbosquid: 3d models for games, architecture, videos. (1202615)
turbosquid
$2
Grenade Mk2
...osquid
royalty free 3d model grenade mk2 for download as max on turbosquid: 3d models for games, architecture, videos. (1658201)
turbosquid
$75
Lanchester Mk2
...alty free 3d model lanchester mk2 for download as 3ds and max on turbosquid: 3d models for games, architecture, videos. (1497085)
turbosquid
$10
MK2 helmet
...
royalty free 3d model mk2 helmet for download as max and obj on turbosquid: 3d models for games, architecture, videos. (1371428)
turbosquid
$10
Grenade MK2
...royalty free 3d model grenade mk2 for download as max and fbx on turbosquid: 3d models for games, architecture, videos. (1146970)
turbosquid
free
MK2 Grenade
...
free 3d model mk2 grenade for download as png, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1225336)
Linear
3ddd
$1
Linear Diffusers
...linear diffusers
3ddd
диффузор
set of linear diffusers for ceiling.
design_connected
$27
Linear Sofa
...linear sofa
designconnected
scp linear sofa computer generated 3d model.
design_connected
$18
Atlantis linear
...atlantis linear
designconnected
terzani atlantis linear pendant lights computer generated 3d model. designed by barlas baylar.
3d_export
$5
light linear unit
...light linear unit
3dexport
light linear unit
turbosquid
$5
Linear Actuator
...
royalty free 3d model linear actuator for download as blend on turbosquid: 3d models for games, architecture, videos. (1589061)
turbosquid
$29
Linear panel
...oyalty free 3d model linear panel for download as max and obj on turbosquid: 3d models for games, architecture, videos. (1391254)
turbosquid
$12
Linear Chandelier
...y free 3d model linear chandelier for download as max and obj on turbosquid: 3d models for games, architecture, videos. (1574289)
turbosquid
$10
Grohe Lineare
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Linear Axis
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Linear Unit 3D Model
...linear unit 3d model
3dexport
linear unit force torque velocity
linear unit 3d model fau 71218 3dexport
Ender
3ddd
$1
Enders / Elegance
...enders / elegance
3ddd
обогреватель
уличный газовый обогреватель enders elegance
высота: 2200 мм
3d_export
free
ender 3 frame cavity covers
... of the creality ender 3 - makes it look a bit more attractive it just slides into the open channels of the aluminium framework
turbosquid
$1
pen support for ender 3
...y free 3d model pen support for ender 3 for download as blend on turbosquid: 3d models for games, architecture, videos. (1611282)
3d_ocean
$9
Ender Dragon Minecraft
...ojang obj poly videogames
ender dragon minecraft created with cinema 4d r15 formats included: max 2013 – fbx 2012 – c4d r15 – obj
3d_export
free
Creality ender enclosure webcam mount
...e creality enclosure. sure is better than a tripod. change it up if it helps. i printed pla with 50% infill on my dd ender 3 pro.
3d_export
free
ender 3 enclosure corners
...er corners and 4 upper corners, using 25mmx25mm angled aluminium pieces that gets covered on inside of the frame with plexiglass
3d_export
free
ender 3 3d print bed clips
...ed + normal aluminium bed frame of the creality ender 3 = 6mm (b) these clips are designed for glass plate + aluminium bed = 4mm
3d_export
$5
GRUMPY CAT
...grumpy cat 3dexport grumpy cat to print in ender ...
3d_export
$5
Logs fire
...with one multi material for corona and vray r ender. albedo, normal, uvmap, roughness format jpg 4096x4096 models:...
3d_export
$42
excavator
...is the original size. 0.12 mm printing surface creality ender5 ...
Core
turbosquid
$143
In the core
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Skandiform Core
...skandiform core
3ddd
skandiform
кресло фирмы skandiform, модель core.
габаритные размеры (шхвхг): 530х700х510 мм
turbosquid
$8
Chandelier CORE
...id
royalty free 3d model chandelier core for download as max on turbosquid: 3d models for games, architecture, videos. (1673910)
turbosquid
free
Planet Core
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Samsung Galaxy Core 2
...samsung galaxy core 2
3ddd
телефон
samsung galaxy core 2
turbosquid
$10
cable 2 core
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
cable 1 core
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Кондиционер ICE CORE
...кондиционер ice core
3ddd
кондиционер
37 000 полигонов
turbosquid
$65
Insulated Multi Core Cable
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$29
Samsung Galaxy Core Advance
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Rails
3d_ocean
$5
rails
...rails
3docean
old rails rails sleepers
old rails
archibase_planet
free
Rail
...chibase planet
rail railing handrail guard-rail
rail forged fence n310814 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Rail
...rail
archibase planet
handrail railing guard-rail
rail n220914 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Rail
...rail
archibase planet
railing hand-rail banisters
rail n130309 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Rail
...rail
archibase planet
railing hand-rail banisters
rail n270510 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Railing
...
archibase planet
railing handrail fence guard-rail
railing n140314 - 3d model (*.gsm+*.3ds+*.max) for exterior 3d visualization.
archibase_planet
free
Railing
...railing
archibase planet
railing
railing- 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Railing
...railing
archibase planet
railing enclosure barrier
light railing - 3d model for interior 3d visualization.
archibase_planet
free
Rail
...rail
archibase planet
metal railing
rail n280608 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Railing
...railing
archibase planet
railing kitchen ware
railing 1 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
5
turbosquid
$6
Rock 5-5
...urbosquid
royalty free 3d model rock 5-5 for download as obj on turbosquid: 3d models for games, architecture, videos. (1639063)
3d_export
$5
hinge 5
...hinge 5
3dexport
hinge 5
turbosquid
$10
A-5
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$2
A-5
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$12
Calligraphic Digit 5 Number 5
...hic digit 5 number 5 for download as max, obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1389333)
3ddd
$1
5 роз
...5 роз
3ddd
5 роз в стеклянной вазе
design_connected
$11
iPhone 5
...iphone 5
designconnected
apple iphone 5 computer generated 3d model.
3ddd
$1
Lola 5
...lola 5
3ddd
miniforms
lola 5 miniforms 300*65*134
3ddd
$1
Nexus 5
...dd
nexus , phone , телефон
google nexus 5 phone
3d_ocean
$15
iPhone 5
...iphone 5
3docean
3d 4d apple cinema iphone model modeling phone screen texture
iphone 5 3d model and texture realistic iphone 5.