Thingiverse
Electrohub Drilling Jig by hotbrass
by Thingiverse
Last crawled date: 3 years ago
A simple jig for drilling the mounting holes for the Flitetest Electrohub and fits 1/2 inch wooden dowels. The unmarked hole in the end should be drilled through regardless of the configuration of the copter. The X holes are for an X configuration quad (should work with hexacopters or octocopters as well) and the S hole is for a spider configuration quad (AKA dead cat quad). It makes consistent, precise drilling much easier and lends to a nicer overall build.
Update: The jig was just a little too long from the end to the first hole. This has been corrected to the ~6mm recommended by flitetest. The original version of this jig was 1-2mm too long for the spider quad booms.
Update: The jig was just a little too long from the end to the first hole. This has been corrected to the ~6mm recommended by flitetest. The original version of this jig was 1-2mm too long for the spider quad booms.
Similar models
thingiverse
free
Accessory Tray, FliteTest ElectroHub by DarinW
... rail system.
for the flitetest electrohub multirotor series.http://flitetest.com/articles/electrohub-battery-tray-and-accessorys
thingiverse
free
Battery Tray, FliteTest ElectroHub by DarinW
...electrohub multirotor series. rails: 3/8" poplar dowel.http://flitetest.com/articles/electrohub-battery-tray-and-accessorys
thingiverse
free
Naze32 flite controller case for electrohub by Norsehound
...ase for electrohub by norsehound
thingiverse
this is a remix of the naze32 case built to accommodate the electrohub by flitetest
thingiverse
free
Motor mount 19mm spacing 13mm boom 1/2" 28mm motor by root
...ck out the flitetest store to purchase the kit: http://store.flitetest.com/electrohub-y6-kit/
i am not affiliated with flitetest.
thingiverse
free
Storm Bolter Drill Jig
...the storm bolter and drill a couple shallow holes. looks way better than i can do free-hand, but i already mentioned my issues...
thingiverse
free
Electrohub battery tray by evilbender
...ery tray by evilbender
thingiverse
battery tray fits to bottom plate of flitetest electrohub. fits 1300mah 3s nanotech battery.
thingiverse
free
FPV Camera Mount by
...s for the camera wires in four positions so that the mount can be attached in any of four orientations, based on your preference.
thingiverse
free
Battery Mount by RomulanAle
...featured in this article on flitetest: http://ec2-54-221-230-83.compute-1.amazonaws.com/articles/angle-arm-mini-electrohub-build
grabcad
free
Jig Drilling
...igs are used to drill holes that are located according to a template. this is useful for drilling holes for patterns and designs.
thingiverse
free
Bookcase Drill Jig
...or a little inaccuracy in hole spacing measurement; make sure the jig is always fitted the same way up to get consistent spacing.
Electrohub
thingiverse
free
Electrohub battery tray by evilbender
...ery tray by evilbender
thingiverse
battery tray fits to bottom plate of flitetest electrohub. fits 1300mah 3s nanotech battery.
thingiverse
free
Mount for Naze32 on Electrohub plate by evilbender
...mount for naze32 on electrohub plate by evilbender
thingiverse
naze32 mount fitted to electrohub top plate.
thingiverse
free
Accessory Tray, FliteTest ElectroHub by DarinW
... rail system.
for the flitetest electrohub multirotor series.http://flitetest.com/articles/electrohub-battery-tray-and-accessorys
thingiverse
free
Battery Tray, FliteTest ElectroHub by DarinW
...electrohub multirotor series. rails: 3/8" poplar dowel.http://flitetest.com/articles/electrohub-battery-tray-and-accessorys
thingiverse
free
Naze32 flite controller case for electrohub by Norsehound
...ase for electrohub by norsehound
thingiverse
this is a remix of the naze32 case built to accommodate the electrohub by flitetest
thingiverse
free
Electrohub Battery Holder by BankNYank
...ard m3 screws and holds the battery in place with a velcro strap. this part is available for purchase at http://rcpartshangar.com
thingiverse
free
CCTV Camera Holder for Anycopter / Electrohub by cvidovcich
...ter way to mount the fat shark cctv camera to my electrohub so i built this little mount. it secures the camera with a nylon tie.
thingiverse
free
ElectroHub inspired Quadcopter by DruckDirDeineWelt
...r by druckdirdeinewelt
thingiverse
all parts are printed with abs and 50% infill.
https://www.youtube.com/watch?v=pibtjo_psuk
thingiverse
free
Electrohub Landing Gear - Long by gsimpson2g
.... the bracket attaches to the side of the rail, with notches to help line it up and keep the landing gear level while tightening.
thingiverse
free
Electrohub Landing Gear - Short by gsimpson2g
.... the bracket attaches to the side of the rail, with notches to help line it up and keep the landing gear level while tightening.
Hotbrass
thingiverse
free
FT Mighty Mini Control Horn by hotbrass
...le control horns for use with the flitetest mighty minis. they are modeled off the free plans provided at flitetest.com. enjoy!
thingiverse
free
Table Saw Runout Gauge by hotbrass
...se a dial indicator from harbor freight to measure table saw runout. you'll need a 1/4" hex bot and nut to assemble it.
thingiverse
free
Remington Pet Crate Latch by hotbrass
...printed it with light supports and it came out pretty well and required minimal cleanup with a small file for aesthetic purposes.
thingiverse
free
Koopaquad by hotbrass
...attach it around a 3d printed micro quad, but i want to keep this entirely 3d printable - which i believe is definitely possible.
thingiverse
free
3508 Motor Mount for .5 inch dowels by hotbrass
...st electrohub. they fit great and seem like they'll be quite strong. they use a standard 25mm x 25mm mounting hole spacing.
thingiverse
free
Size 2 Xacto Anit-roll - TPU by hotbrass
...n tpu, it's a snug fit that stays put. works great, and now i don't have to do a little dance every time my xacto rolls.
thingiverse
free
DMT DiaSharp Sharpener Holder by hotbrass
...ed 4 rubber feet to each one to keep it from sliding on the desk.
so far, they are working great. happy printing and sharpening!
thingiverse
free
Magnetic Vent Connector by hotbrass
...i have mounted in the window.
so far, it's working really well and makes hooking up the vent much easier and quicker. enjoy!
thingiverse
free
Challenge Coin Holder (Desk or Wall Mount) by hotbrass
...d hole for a screw (m3 flat/tapered head) if you'd like that option. this will also sit on a desk and hold the coin as well.
Jig
turbosquid
$25
jig-saw_mid_SM
...uid
royalty free 3d model jig-saw_mid_sm for download as obj on turbosquid: 3d models for games, architecture, videos. (1244761)
turbosquid
$20
jig-saw_low
...osquid
royalty free 3d model jig-saw_low for download as obj on turbosquid: 3d models for games, architecture, videos. (1244760)
turbosquid
$10
jig-saw_hi
...bosquid
royalty free 3d model jig-saw_hi for download as obj on turbosquid: 3d models for games, architecture, videos. (1244757)
turbosquid
$7
Jig Armchair
...squid
royalty free 3d model jig armchair for download as max on turbosquid: 3d models for games, architecture, videos. (1648936)
turbosquid
$5
Jig Tail
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$5
Jig Head
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$5
Jig Head
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$5
Jig Head
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$5
Jig Head
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$5
Jig Head
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Drilling
archibase_planet
free
Drill
...drill
archibase planet
drill electric drill power drill
drill n091107 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Drill
...drill
archibase planet
drill hand drill
drill 1 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Drill
...drill
archibase planet
drill hand drill
drill 2 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Drill
...drill
archibase planet
drill hand drill
drill 3- 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Drill
...drill
archibase planet
boring rig rig drill
drill n070807 - 3d model for interior 3d visualization.
archibase_planet
free
Drill
...drill
archibase planet
hand drill toolware
drill 2 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Drill
...drill
archibase planet
perforator drill auger
drill 3 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
$25
Drill
...ll
turbosquid
royalty free 3d model drill for download as ma on turbosquid: 3d models for games, architecture, videos. (1203923)
turbosquid
free
Drill
...l
turbosquid
free 3d model drill for download as fbx and obj on turbosquid: 3d models for games, architecture, videos. (1628646)
archibase_planet
free
Drill
...drill
archibase planet
boring mill perforator driller
drill pro 1 - 3d model (*.gsm+*.3ds) for interior 3d visualization.