Thingiverse
Egg Shaped Speaker by jongdepaul
by Thingiverse
Last crawled date: 3 years ago
An egg shaped loudspeaker enclosure, designed this with Tinkercad.
The first incarnation fits a pretty much run of the mill 4" (11.5cm) full range driver. I am using a speaker I had laying around collecting dust. It's designed for a full range driver so its easy to wire up and you don't need any filters etc.
Printed in an upright position (no supports needed) with 0.2mm resolution at 5cm/sec which took a good 15 or so hours to do. Its nearly 16cm tall so make sure your printer can handle this. If the speaker is too tall you could try to print it face down but you will need supports because of the inset ring for the speaker
I chose to use wood filament as I have been wanting to use it for something like this. After experimenting with finishes on the first print I decided to not do any sanding - the lines made by the printer give a pretty good wood-like look. I have experimented with a couple of stains too and ended up choosing "Old Baltic" by Feast Watson followed by a coat of clear glossy varnish. See the pictures that show the finished "product" (except for the ugly stainless screws that will be replaced by stylish black ones soon).
There is also a version that fits a Dayton Audio RS-100 full range driver. The photos of the stained finished speaker show what it looks like with these drivers. Do be aware that these drivers aren't the cheapest - they cost around $50 (AU$) a pop so you are looking at a sizeable investment.
NOTE: I am not an audio engineer, nor an electronics engineer, nor did I do any clever calculations etc to try and make this the best sounding speaker. I designed it for based on what I thought would make a nice looking unit
The first incarnation fits a pretty much run of the mill 4" (11.5cm) full range driver. I am using a speaker I had laying around collecting dust. It's designed for a full range driver so its easy to wire up and you don't need any filters etc.
Printed in an upright position (no supports needed) with 0.2mm resolution at 5cm/sec which took a good 15 or so hours to do. Its nearly 16cm tall so make sure your printer can handle this. If the speaker is too tall you could try to print it face down but you will need supports because of the inset ring for the speaker
I chose to use wood filament as I have been wanting to use it for something like this. After experimenting with finishes on the first print I decided to not do any sanding - the lines made by the printer give a pretty good wood-like look. I have experimented with a couple of stains too and ended up choosing "Old Baltic" by Feast Watson followed by a coat of clear glossy varnish. See the pictures that show the finished "product" (except for the ugly stainless screws that will be replaced by stylish black ones soon).
There is also a version that fits a Dayton Audio RS-100 full range driver. The photos of the stained finished speaker show what it looks like with these drivers. Do be aware that these drivers aren't the cheapest - they cost around $50 (AU$) a pop so you are looking at a sizeable investment.
NOTE: I am not an audio engineer, nor an electronics engineer, nor did I do any clever calculations etc to try and make this the best sounding speaker. I designed it for based on what I thought would make a nice looking unit
Similar models
3dwarehouse
free
Galaxy Audio S5N-8 5' Neodymium Full Range Driver 8 Ohm
...io s5n-8 5' neodymium full range driver 8 ohm #5 #8_ohm #audio #design #driver #full #galaxy #neodymium #range #s5n8 #speaker
thingiverse
free
Egg Speaker Enclosure by lithochasm
...m/dayton-audio-nd16fa-6-5-8-soft-dome-neodymium-tweeter--275-025
x-over
4.7uf 100v electrolytic non-polarized crossover capacitor
thingiverse
free
Dayton Audio Karlson Style Speaker by Jaykoyote
... x2
see the picture for where to glue the screw parts, i used 5-minute epoxy to glue them in place.
thingiverse
free
Speaker Enclosure for 4" Driver by jongdepaul
...be using this design as the base for something similar to my modular sound bar allowing you to print...
thingiverse
free
Full Range Speakers, 4" Dayton Audio RS100-4 by Kapman1
...truction details. these speakers can be used "as-is" or combined with the matching subwoofer posted here: subwoofer.
thingiverse
free
Speaker Enclosure by jh321
...ad output screen.
i designed this for minimal supports (only the baffle) as long as the rear of the speaker isn't too flat.
thingiverse
free
Woven Egg Puzzle by Zoips
...eaving is extra tricky, so i recommend that you start with a skinny egg.
the final product is a beautiful decorative egg. enjoy!
thingiverse
free
Full Range Speaker Enclosure with Adapter Plate
... which is 1.5" or 38.1mm out of a salvaged bluetooth speaker. i have included an adapter plate to make the enclosure modular
thingiverse
free
Spherical Speaker Enclosure (Ported) - Dayton PS95-8 by B_Rich
...he finished product.
http://imgur.com/a/zdejb
tips are welcome but don't ever feel obligated to do so! :)
thanks for looking!
thingiverse
free
Shell Speaker by alexmordue
...#39;ll also need some silicone sealant or epoxy resin to fill the hole from the bottom once you've got your speaker wires in.
Jongdepaul
thingiverse
free
Tool Carousel by jongdepaul
... tube simply slides onto the base and the top slides into the tube.
does anyone know why my pla is going white on the print bed?
thingiverse
free
Modular Surround Speaker by jongdepaul
...expensive) store bought (jaycar australia) ones.
as with the sound bar, please let me know how you go if you end up making these.
thingiverse
free
PlotClock Arm for Artline 500A Whiteboard Marker by jongdepaul
...is slightly higher to give some extra strength.
i since found that this arm also fits the staedtler lumocolor whiteboard markers.
thingiverse
free
Speaker Enclosure for 4" Driver by jongdepaul
...uced the layer height to 1.5mm. print time was well over 24 hours at 6cm a second with 20% infill so you will have to be patient.
thingiverse
free
Cocoon Create (Wanhao Duplicator i3 v2) Filament Guide and Tool Holder by jongdepaul
...reate so it should also fit the wanhao duplicator i3 (v2)
this is only the second design i put up here so please go easy on me :)
thingiverse
free
Two Way Tube Satellite Speaker by jongdepaul
...) so please be kind :) i have identified some things that could be done differently so as i make changes i will update this post.
thingiverse
free
2 Way Orb Speaker by jongdepaul
...ur ipod (or other device with a headphone jack) is now available as a separate download https://www.thingiverse.com/thing:2348151
thingiverse
free
Orb Amp - Amplifier for the Orb Speaker by jongdepaul
...put and an rca jack for the output. for the rest all you need is a few screws, a few plugs and a bit of wire to make it all work!
thingiverse
free
Modular 3D printable Sound Bar / Center Speaker by jongdepaul
... supports to print the brackets.
** you will need to have some experience in soldering and electronics to complete this project.
Egg
3d_ocean
$2
Egg and Egg Cup
...egg and egg cup
3docean
breakfast eating egg egg cup eggcup food
an egg in an egg cup
3d_ocean
$6
Easter Egg Set and Egg Cup
...xtured eggs and one egg cup. striped textures are editable – .pdf files are included in the set. one egg contains 2,368 faces ...
3d_ocean
$6
Eggs Set
...lective scene textures
different types of eggs, including easter egg, golden egg..etc render set-up, materials, texture included.
design_connected
$9
Egg
...egg
designconnected
bonacina pierantonio egg computer generated 3d model. designed by ditzel nanna, joergen.
3d_export
$25
a shatterable egg - broken eggs
...a shatterable egg - broken eggs
3dexport
texture size:512px number of texture:4 texture format: png 1 texture= 1 egg
3d_ocean
$2
Easter Egg
...easter egg
3docean
easter egg food holiday
easter egg with texture.
3d_ocean
$1
3D Eggs
...ter eggs eggs
3d eggs ready for decoration! easter is coming! easy editable , uv wrapped ,zip contains : blend,obj,uv layout png.
design_connected
$20
Egg
...ignconnected
photo-realistic 3d models of the egg chair by arne jacobsen for 3d architectural and interior design presentations.
3d_export
$6
fried eggs
...fried eggs
3dexport
fried eggs
3d_export
$5
egg house
...egg house
3dexport
egg house
Speaker
3d_ocean
$12
Speakers
...speakers
3docean
beautiful customizable customizable speakers
speakers 3d model
3d_ocean
$5
Speaker
...speaker
3docean
audio speaker
minimalist audio speaker for your design.
3d_export
$5
speaker
...speaker
3dexport
speaker
archibase_planet
free
Speaker
...er
archibase planet
acoustic system column speaker loud speaker
speaker 3 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Speaker
...er
archibase planet
column speaker loud speaker acoustic system
speaker 2 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Speaker
...er
archibase planet
loud speaker column speaker acoustic system
speaker 1 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Speaker
...speaker
archibase planet
speaker audio
speaker din - 3d model for interior 3d visualization.
archibase_planet
free
Speakers
...speakers
archibase planet
speaker speakers audio
speakers1 - 3d model for interior 3d visualization.
3d_ocean
$6
Speaker
...speaker
3docean
3d model music sound speaker
model,3d,speaker,sound,best,music
3d_ocean
$4
Speaker
...speaker
3docean
audio computer desktop electronic headphone microphone music pc speaker speakers technology
.
Shaped
archibase_planet
free
Shape
...shape
archibase planet
form shape
decor shape n070707 - 3d model for interior 3d visualization.
3d_export
$7
shaped ball
...shaped ball
3dexport
shaped ball
3ddd
$1
Shapes Aqua
...shapes aqua
3ddd
кальян
кальян shapes aqua
высота кальяна: 70 см.
производитель: shapes
3ddd
$1
Кресло Shape
...кресло shape
3ddd
tonon
кресло shape итальянской фирмы tonon
размер, см.: 73х61х63.
3d_ocean
$9
6 Plexus Shapes
...us shape green points : 30397 polygons : 26626 plexus shape violet points : 28734 polygons : 25136 liquid shape 1 points : 454...
3ddd
$1
Twist Shape
...twist shape
3ddd
скамья
уникальный и стильный скамья с twist shape в середине - s городской скамьи
archive3d
free
Shape 3D Model
...pe 3d model
archive3d
form shape
decor shape n070707 - 3d model for interior 3d visualization.
3d_export
$5
bolted shape ring
...bolted shape ring
3dexport
bolted shape ring
3d_export
$5
shape door knob
...shape door knob
3dexport
shape door knob
turbosquid
$13
pear shape
...bosquid
royalty free 3d model pear shape for download as stl on turbosquid: 3d models for games, architecture, videos. (1278323)