Thingiverse
Earring Stand by billyd
by Thingiverse
Last crawled date: 3 years ago
This is an earring stand I designed for my wife. I provide a .8mm support box for the cross brace, so it's best to print with .4mm extrusion width. Add supports between the cross brace and the support box. I found this prints better than just running supports all the way up from the build bed. Also I would advise using PLA or PETG for this print.
I also supply the stand with just holes instead of slots for stud earrings.
Enjoy!
I also supply the stand with just holes instead of slots for stud earrings.
Enjoy!
Similar models
thingiverse
free
Rocking launch stand cross braces (sacrificial layer) by DRPrinting3D
...to include a sacrificial layer at the top of the holes for the nuts. this way they should print clean without using any supports.
thingiverse
free
Mini Cross Bow Stand by MechaNeko
... steve thone.
i have also included a mod for the cross bow to prevent misfires, just print and mount to the top of the cross bow.
thingiverse
free
Brace for Tronxy P802
...for more stiffness of the frame
print the brace standing-up without support
printed on my tronxy p802
0.15mm hight and 20% infill
thingiverse
free
ipad stand by shomirb
... cross-brace. you also might want to run a bead of hot glue on the edge to make it more sticky on glass or other smooth surfaces.
thingiverse
free
Picture Frame 5x7 by slackersean
...with no supports. brace and back plate can be printed flat with no supports as well. does require a wide build plate to lay flat.
thingiverse
free
Star Wars Display Stand w/braces by Geekdad_3D
... and maybe i didn't use a good enough infill but the arms broke right away. i added some vertical support braces to the arms.
thingiverse
free
Spooler Brace by johnmcwGeo
...arn spooler very stable (great for spooling filament). print 2 of these in addition to the yarn spooler. i glued them in place.
thingiverse
free
Customizable Earring Stand by stylesuxx
...f you want them shorter, or can print them longer. also you can adjust the spacing between the holes and the radius of the holes.
thingiverse
free
Stackable Ear Saver Stand by chrisgouldis
...'t have any cross support on the wedge.
i printed these at 0.2 and 15% infill but it really shouldn't matter for either.
thingiverse
free
CR-10 Spool Brace by GeneralLeeStupid
...l like this affects print quality so i modeled a support that slides into the holders tube and braces it against the control box.
Billyd
thingiverse
free
Golf Box by billyd
...plify printing.
the lid should be dropped about 1mm into the bed before slicing. the lid will need supports around the perimeter.
thingiverse
free
Nerdcam3D MK2 Mount by billyd
... camera and tricopter!
enjoy
update added file nerdcam3d-mk2_cover_mobius which is a cover with a mount for the mobius hd camera.
thingiverse
free
Filament Saver by billyd
... when not in use. it saves filament because the device does not damage or require bending the filament to keep it from unspooling
thingiverse
free
Facehugger by billyd
...actice with my scanner, i am learning quite a bit. so i've just uploaded a much better quality scan of the facehugger. enjoy!
thingiverse
free
Christmas Tree Star Topper by billyd
...revised it so it could be printed in two halves and glued together to make a whole. note this is a small tree topper. 118mm wide.
thingiverse
free
Exhaust Fitting, Wall Mount by billyd
...t is meant as a means to mount the exhaust tube to a dryer vent or similar on a wall, to carry the printed exhaust fumes outside.
thingiverse
free
Nerdcam3D Mount for Cinetank MK2 by billyd
...locations on the forward top of the cinetank mk2 upper plate. nerdcam3d with cinetank mk2 frame is an amazing experience. enjoy!!
thingiverse
free
Handle for Lulzbot Taz 4 or 5 enclosure by billyd
...h side of my lulzbot enclosure for taz 4 or 5 (found here: http://www.thingiverse.com/thing:746922 ) for easy lifting and moving.
thingiverse
free
Hero2 mount for the Firefly 6 by billyd
...pt a single "one-wrap" style velcro tie 8x1/2". you can typically find them in retail stores in the craft section.
Earring
thingiverse
free
Earrings
...earrings
thingiverse
earrings
thingiverse
free
Earrings
... lightweight earrings, made by printing 3 different parts in differents colors, and then attaching them with some earrings hooks.
thingiverse
free
Earring by lawfool26
...earring by lawfool26
thingiverse
earring
thingiverse
free
Earring 2020
...earring 2020
thingiverse
earring
thingiverse
free
earring by Dzecko
...earring by dzecko
thingiverse
earring
thingiverse
free
Earrings by Mari5Gt
...earrings by mari5gt
thingiverse
earrings
thingiverse
free
earrings by SE3D_workshop
...earrings by se3d_workshop
thingiverse
earrings
thingiverse
free
earring by Mrsanfy07
...earring by mrsanfy07
thingiverse
earring
thingiverse
free
ear by nagato
...ear by nagato
thingiverse
ear
thingiverse
free
earring by hdirim
...earring by hdirim
thingiverse
earring
Stand
thingiverse
free
Stand-stand by Fank86
... all your troubles go away, .1mm at a time!
and no, i did not make this in 15 seconds to poke fun at all the stands on this site.
thingiverse
free
stand
...stand
thingiverse
a stand
thingiverse
free
A stand
...a stand
thingiverse
a stand.
thingiverse
free
Stand
...stand
thingiverse
this is a stand, nothing more !
thingiverse
free
stand
...stand
thingiverse
this is a stand that you can put things on
thingiverse
free
Headset stand with phone stand
...dset stand that doubles as a phone stand, the phone also can be charged while on the stand.
leave a comment if you have feedback
thingiverse
free
hairdryer stand and Curling iron stand
...hairdryer stand and curling iron stand
thingiverse
hairdryer stand and curling iron stand
thingiverse
free
Inbus Stand / Inbuskey Stand
...workshop.
this inbuskeys fitts perfectly in that stand:
8 ; 6 ; 5 ; 4 ; 3 ; 2,5 ; 2
enjoy your print :)
comment below if it works
thingiverse
free
Stand by cmaines
...stand by cmaines
thingiverse
stand
thingiverse
free
stand by Syzguru11
...stand by syzguru11
thingiverse
stand