Eachine TX02 by Cselloman

...eachine tx02 fpv camera holder by webdimmy thingiverse eachine tx02 fpv camera holder

...aio camera mount for eachine aurora 100 by daemonz144 thingiverse eachine tx01 tx02 tx03 aio camera mount for eachine aurora 100

...eachine tx02 by bankboom thingiverse camera : eachine tx02 ---> https://goo.gl/hnzgrq angle : 20 degree material : tpu

...y whoop mount by tweetfpv thingiverse printed with tpu. mount for the eachine tx02 for a tinyh whoop. this mount has no up tilt.

...tx01 tx02 tx03 support by ph3nyx thingiverse support for eachine tx01 tx02 tx03 camera

...e for lightweight builds. this will accommodate a aio eachine tx02 camera and serve as the final top plate for any stacked build.

...tx02 camera mount 16x16 by bankboom thingiverse i printing with tpu material. installing hole: 16x16mm camera : eachine tx02

...rinted in abs for durability but pla will work too. this will fit cockroach, whoop, eachine e010 frame (front screw hole unused).

... the camera+vtx tx02 from eachine to mount on a qx90 micro drone. just need a little bit of hot glue to maintain it during flight

...eachine tx02 tx01 mount for qx95 by erkark thingiverse no support need

... created the 1:1 copy of the qavx/realacc x210 purpose of creating a pod for it. hope it helps others to try out their skills. :d

...bbs hub cap by cselloman thingiverse pint it and seal off the wheel hub to prevent dust and moisture to get in. :)

...tgy-ia6c receiver by cselloman thingiverse this is the new tgy ia6c receiver in 3d form without the plastic wrap.

...holes for the vtx. i will update as i go along. original design by cselloman found here http://www.thingiverse.com/thing:1852479

...harger cab easy print slices (no support) by cselloman thingiverse print parts in a standing position, so you dont need support.

...nd suggestions are welcome in message! thanks for getting in. :) for attaching to the main plate, use wood screws 2.9mm(m3)x12mm.

... print it with ~101% to have a snug fit. mine fits well, but a bit easy to remove. not a problem since the strap pulls it anyway.

...210x pod remixes by dblnaknak thingiverse i remixed cselloman#39;s excellient pod design. i added a whale tail, lol,...

...tx02 mounting by axljackass thingiverse mounting for tx02

...eachine tx02 by bankboom thingiverse camera : eachine tx02 ---> https://goo.gl/hnzgrq angle : 20 degree material : tpu

...tx01 tx02 tx03 support by ph3nyx thingiverse support for eachine tx01 tx02 tx03 camera

...tx02 camera mount 16x16 by bankboom thingiverse i printing with tpu material. installing hole: 16x16mm camera : eachine tx02

...eachine tx02 fpv camera holder by webdimmy thingiverse eachine tx02 fpv camera holder

... one with 5° tilt, the second without tilt. perfect fit for tx02 aio fpv camera used with eachine qx95 or qx90 or all qx familly.

...e for lightweight builds. this will accommodate a aio eachine tx02 camera and serve as the final top plate for any stacked build.

... the camera+vtx tx02 from eachine to mount on a qx90 micro drone. just need a little bit of hot glue to maintain it during flight

...eachine tx02 tx01 mount for qx95 by erkark thingiverse no support need

...ingiverse simple lightweight clip to mount the eachine ev100 micro av recorder to a 19mm strap of the eachine ev100 fpv goggles.

...eachine twig canopy thingiverse canopy for the eachine twig drone.

...or the eachine ts5828l thingiverse this is a support for the eachine video transmitter tx5828l. made it to use with zaggy wings.

...eachine rotg02 box by lorent_den thingiverse eachine rotg02 box

...ducts for eachine cvatar by dalodi thingiverse ducts for eachine cvatar

...eachine e010 controller by ejpsx thingiverse eachine e010 controller

...ine vr d2 goggles thingiverse you can read more about the upgrade on: http://lll.mk/fpv/eachine-pro58-boxed-goggles-on-steroids/

...eachine vtx lt200 case thingiverse case for vtx eachine lt200

...eachine e010 stick by danif thingiverse stick for rc eachine e010