Thingiverse
E6804 Case by JediKnight2
by Thingiverse
Last crawled date: 3 years ago
A case for the E6804. I placed the holes on the front face of the top of the case so that you could pass wires through. My plans are to use 4 core pigtails with strain relief on the inside. I also placed a little ledge that extends down from the top of the case to keep the Ethernet Module pressed down and secure.
UPDATED 4/29/2016 Removed the lower 2 holes and re-positioned the holes along where the top and middle holes were aligned. The lower 2 holes would have allowed for wire to pass through, but the fuses were slightly in the way.
UPDATED 4/29/2016 Removed the lower 2 holes and re-positioned the holes along where the top and middle holes were aligned. The lower 2 holes would have allowed for wire to pass through, but the fuses were slightly in the way.
Similar models
thingiverse
free
4-in Desk Hole Plug/Cord Opening by JNJLabbe
... settings, sanding (or scaling down slightly) may be required in order for the part to fit. i forced mine in place with a mallet.
thingiverse
free
Printer Corner Anchors by SangreDeDrago
... a wire passing through its center and up through a hole in the platform and back down another hole next to it to create tension.
thingiverse
free
USB emulator enclosure
...in jst connectors. after passing wires through the input hole, i knotted the cable to prevent stress to the connectors and board.
grabcad
free
Jig for wire cutter
...jig for wire cutter
grabcad
the wire passes through the center of the hole.
thingiverse
free
Nodemcu and and ili9341 case for solderless wiring by enigma_x
...o allow solderless wiring. the hole for the usb connection is large enough for the wires to pass through to the back of the arm.
thingiverse
free
44 MM HOLE WIRE MONITOR COMPUTER CABLE MANAGEMENT HIDE by Sballa79
...re monitor computer cable management hide by sballa79
thingiverse
cable management for 44 mm hole pass through
print upside down
thingiverse
free
TBS Race Tracker Mod case by DavidCanfield
... install two m3 bolts to the bottom two holes
9) place the antenna support over the antenna and install the remaining 2 m3 bolts.
thingiverse
free
TBS Unify Pro Race VTX Case (Stackable 30.5mm Hole Spacing) by ahuddart
... race video transmitter, hole spacing of 30.5mm to fit on flight controller stack. pass through for push button on top of case.
thingiverse
free
Brackets for Drag chain by PCFlyer
...own" end piece. i had a difficult time getting to the lower holes once multiple wires were passing through it. this works.
thingiverse
free
4 18650 cell thingamajig
...htly looser for the 2 inner ones due to the less support in between. i may put a little wall between the inner 2 cells if needed.
Jediknight2
thingiverse
free
Power Supply Mounts by JediKnight2
... supply mounts by jediknight2
thingiverse
power supply mounts for the typical 12v 300w power supplies used in christmas lighting
thingiverse
free
12mm to 9 gauge wire clip by JediKnight2
...12mm to 9 gauge wire clip by jediknight2
thingiverse
12mm pixel to 9 gauge wire
thingiverse
free
Soldering Hand by JediKnight2
...pixels in. seemed like i always needed an extra hand when trying to fiddle with the wires when soldering in a replacement pixel.
thingiverse
free
E682 Case by JediKnight2
... me know.
i have not printed this yet! check my measurements! i will remove this warning once i get a chance to print the case!
thingiverse
free
MTC Gutter Clip V.3 by JediKnight2
...ngiverse
a shingle clip that holds 1/2" pvc. allows you to zip tie christmas lights to the pvc so you have straight lines.
thingiverse
free
Falcon F16V2 Mount and Plexi Glass Cover by JediKnight2
... mount for mounting on a board or wall. i also included a plexi glass mount system that covers the board somewhat to protect it.
thingiverse
free
MindTrik Gutter Clip by JediKnight2
...traighter lines with your lights. it also has a small clip on the top so you can run any other wiring separate from your lights.
thingiverse
free
Grossfillex Sunset Umbrella Insert by JediKnight2
... the nuts were lost for a table. this nut has more threads on it so it should hold a little tighter.
i would use asa over abs.
thingiverse
free
Boscoyo PixaBulb Strip Megatree Hooks by JediKnight2
...he strip from an eye hook. the bottom is made to fasten the same way, but there's a hole for using a zip tie for the bottom.
Case
3d_export
$1
case
...case
3dexport
case
archibase_planet
free
Case
...case
archibase planet
showcase show-case glass case
glass-case + cakes - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
showcase show-case glass case
glass-case for chips - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case shelving drawer
case - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case rack locker
case - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case drawer kitchen furniture
case - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case cupboard shelving
glass case - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case handbag suitcase
case - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case suitcase
case 5 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
locker case dresser
case - 3d model (*.gsm+*.3ds) for interior 3d visualization.