Thingiverse
E3D V6 FOR UM2 (空中堡垒) by slangel
by Thingiverse
Last crawled date: 4 years, 1 month ago
打印建议：
材料：ABS / PLA
填充：30%
层高：0.1 - 0.2
注意：在放置方片螺母的任何管道中不要加支撑，除非您的支撑非常好拆。只需要在两个轴承孔内，和顶部保持架的位置加上支撑即可。
螺丝：
M3 15mm (6 枚)
M3 10mm (2 枚)
螺母：
方片螺母 5.5 * 2.5 (6 枚)
风扇：
4010 (3 枚)
组装说明：
首先将两个用于锁紧轴承的方片螺母推入方片螺母的管道中，然后放入两枚轴承，再用M3 * 15的螺丝拧紧。
再将锁紧E3D V6的方片螺母从顶部推入到对应位置，放入E3D后合上盖后锁紧，继续将锁紧保持架的螺母从顶部推入到对应位置，锁紧。至此E3D部分安装完毕。
将打印的风道通过M3 * 10的螺丝直接拧入十字滑块底部的螺丝孔中。
将所有风扇安装到对应位置。
完成，开始享受吧！！！
Print advice:
Material: ABS / PLA
Fill: 30%
Storey height: 0.1 - 0.2
Note: do not support any pipe where the square nuts are placed unless your support is very well removed. It only needs to be supported in the two bearing holes and the top cage.
Screw：
M3 15mm (6)
M3 10mm (2)
Nut：
Square nut 5.5 * 2.5 (6)
Fan:
4010 (3)
Assembly Description:
First, two square nuts used for locking bearings are pushed into the pipe of square nuts, then put into two bearings and tightened by M3 * 15 screws.
Then push the lock nut of E3D V6 into the corresponding position from the top, then put the E3D back up and lock it, and continue to push the lock holder nut from the top to the corresponding position and lock tightly. At this point, part of the E3D is installed.
Screw the print air duct through the screw of M3 * 10 directly into the screw hole at the bottom of the cross slide block.
Install all the fans to the corresponding position.
Do it, start enjoying it!!!
材料：ABS / PLA
填充：30%
层高：0.1 - 0.2
注意：在放置方片螺母的任何管道中不要加支撑，除非您的支撑非常好拆。只需要在两个轴承孔内，和顶部保持架的位置加上支撑即可。
螺丝：
M3 15mm (6 枚)
M3 10mm (2 枚)
螺母：
方片螺母 5.5 * 2.5 (6 枚)
风扇：
4010 (3 枚)
组装说明：
首先将两个用于锁紧轴承的方片螺母推入方片螺母的管道中，然后放入两枚轴承，再用M3 * 15的螺丝拧紧。
再将锁紧E3D V6的方片螺母从顶部推入到对应位置，放入E3D后合上盖后锁紧，继续将锁紧保持架的螺母从顶部推入到对应位置，锁紧。至此E3D部分安装完毕。
将打印的风道通过M3 * 10的螺丝直接拧入十字滑块底部的螺丝孔中。
将所有风扇安装到对应位置。
完成，开始享受吧！！！
Print advice:
Material: ABS / PLA
Fill: 30%
Storey height: 0.1 - 0.2
Note: do not support any pipe where the square nuts are placed unless your support is very well removed. It only needs to be supported in the two bearing holes and the top cage.
Screw：
M3 15mm (6)
M3 10mm (2)
Nut：
Square nut 5.5 * 2.5 (6)
Fan:
4010 (3)
Assembly Description:
First, two square nuts used for locking bearings are pushed into the pipe of square nuts, then put into two bearings and tightened by M3 * 15 screws.
Then push the lock nut of E3D V6 into the corresponding position from the top, then put the E3D back up and lock it, and continue to push the lock holder nut from the top to the corresponding position and lock tightly. At this point, part of the E3D is installed.
Screw the print air duct through the screw of M3 * 10 directly into the screw hole at the bottom of the cross slide block.
Install all the fans to the corresponding position.
Do it, start enjoying it!!!