Drive Rail by sgk07072000

...lenovo c20 hard drive rails by jmcskixc thingiverse slide-in mounting rails for a lenovo c20 computer hard drive.

...4040 sbr12uu linear rail gantry drive mechanism by kieranod thingiverse 4040 gantry on sbr12uu linear rail drive mechanism

...3.5" hard drive rails reversed by holduspokus thingiverse reversed 3.5" hard drive rails from visionkj

...rive rails by visionkj thingiverse needed a set of plastic 3.5" hard drive rails. very simple, but work just fine. -enjoy!

...irror the model for the other rail. the anchors are there to prevent warping and should be clipped off after the print completes.

...ls by absorbthefuture thingiverse i remixed the herome base to work for my setup with micro swiss direct drive and linear rails.

...direct-drive extruder mount final version 191111: direct-drive-extruder-mount final version 191124: direct drive tube mount added

...s is a remix of speeddrive v1 - ender 3 direct drive mount by sashalex007 to fit ender 5 linear rails mod by kerseyfabrications.

...t are optional. countersink holes are meant for flat top screws if you want a flush outside (good for placing these side by side)

...of the drive rails - they prevent side to side movement and you can even use damaged trays successfully with the shims installed.

...filament guides by sgk07072000 thingiverse roller filament guides

...ring 5 by sgk07072000 thingiverse a ring my wife and i designed.

...hall endstop by sgk07072000 thingiverse this is my version on a hall-o endstop

...y-undercarrage by sgk07072000 thingiverse this is a one piece y under carriage.

...pill box by sgk07072000 thingiverse this is a pill box based on the code for my sunglass case.

...milk crate corners by sgk07072000 thingiverse corners for mounting a prusa mendel on top of a milk crate.

...i run some wires in the 10x20 rail slots of my printer and this clip keeps the cables in the slots. they are tiny but they work.

...ilk crate spool mount by sgk07072000 thingiverse mount for holding a spool mounted on a 8mm, 5/16" rod within a milk crate.

...t was pathetic. i designed this piece to fill all the space and to expand as it was screwed on so that it made a nice tight fit.

...vector rail thingiverse vector rail

...railing thingiverse for gaming and modeling

...fingerboard rail thingiverse cool rail for fingerboarding!!!!

...guide rail thingiverse different guide rail options. i found the long rail provide to most stability.

...rail for tramways thingiverse it is just a replacement for the rails of tramways.

...scope rail by rundown thingiverse scope rail for a lower rail.

...u need. this rail segment has a 1 inch wide baseplate. this surface is what i used to glue the rail into the target application.

... and realized it used a dovetail rail contrary to a picatinny rail, made this and super glued it on my rifle, no problems so far.

...ak side rail mount with extra rail by homiestarks thingiverse just added another rail on it.

...y rail adapter. you can either print a long 'combined' rail, or separate parts, and glued them together (easier to print)

...usb drive / flash drive / pen drive case by brosjr thingiverse spare part for a broken usb drive case. my mom´s request :-)

...turret drive thingiverse drive key and housing

...ot of flash drives for various purposes so while 20 drives may sound like a lot, this is only one of 3 that i am currently using.

...have created for the ender3 and should fit the cr10 printers. this is for the duel drive mount version not the standard version.

...drive shaft by redmerlin thingiverse a drive shaft.

...driving message by mariblueruby thingiverse cheeky driving message

...ve case by evanvs thingiverse this is a case for an external usb harddrive. this case is designed to fit the "g-drive"

...mk2 drive bashguards thingiverse bashguards for the mk2 avio at gear drive!

...harmonic drive thingiverse harmonic drive i made, uses 7.9 mm steal ball bearings. make sure to split into parts before printing

...waterjet drive thingiverse waterjet model