Drain resin orange30

...drain bracket for yooin2 resin 3d printer by hu5566798 thingiverse drain bracket for yooin2 resin 3d printer

...onfu thingiverse self designed resin drain cover filter in bathroom. hair stopper in bathroom. could be printed without support.

... to drain off the part and build plate back into the vat. printed out of pla at 0.2 layer height with 10% infill and no supports.

... by 3d_print_pt thingiverse drain bracket for the voxelab proxima 6" resin 3d printer v2 added some clearance for the knob.

...resin tank and stand will fit under the mars 2 cover to shield uv while draining. assembled using four 3x18mm button head screws.

...logs ) for replacement in heroquest board game. included a hollow version for resin printers, with some holes for resin draining.

...esin to drain off. it's tilted to drain off at one corner. you can even leave the cover on while you wait for it to drip dry.

...e resin but will drain over time, essentially it will look like frozen ice with a bit of water trapped in a skull bubble... ymmv.

...at either 60 or 90 degrees. print the part for strength. use a structural resin or many (4-5) perimeters if using a fdm printer.

...sla/dlp by zeru thingiverse i wanted to save some resin so i used meshmixer to hollow it out and added a drain hole to the base.

...ips into the cooling vent holes on the side of the printer. printed from pla with 0.2mm layer height, 10% infill and no supports.

... to drain off the part and build plate back into the vat. printed out of pla at 0.2 layer height with 10% infill and no supports.

...f the printer and hold the allen keys/wrenches and scraper. printed from pla with 0.2mm layer height, 10% infill and no supports.

...my hand at modeling in fusion360. printed on the orange30 with siraya blu at .1mm layer height, 4 bottom...

...drain by shingabiss thingiverse drain

...draining net thingiverse its a draining net for bonsai

...drain by runevik thingiverse drain pipe for a kitchen sink

...shower drain insert thingiverse this goes in a shower drain and allows the drain cover to back on as normal

... plastic shower drain broke so i copied the shape and made a new one. pla seems to work fine. square shower drain cover. 10x10 cm

...drain-pan by leask thingiverse a drain-pan design for kitchen https://github.com/leask/drain-pan

...shower drain by strider1 thingiverse shower drain

...shower drain by 5f5ygfd thingiverse shower drain

...the drain filter by katu thingiverse the drain filter

...bath tub drain thingiverse great drain cover

...; low and behold, i give you...... the scrapork!! designed to scrape the resin off your fep and collect the lose chunks of resin.

...ired by a recent video of my favorite couple evan & katlyn, i printed this model and soon i will pour resin in it as they did

...o need a handle for it, it should fit on a 4 inch paint roller. print on pla so it can be cleaned in acetone to remove the resin.

...non-aerating resin mixer thingiverse resin mixer for m6 thread. mix well and does not aerate the resin.

... fit a paper filter and the taper is relieved to add clearance where the filter screen is located, promoting improved resin flow.

...mall fragments as it combs through resin. this is the prototype (100mm long). print it flat on the print bed, for best strength.

...less mess and for fine pouring in tight molds and small cavities. works great for casting multiple color resin/hybrid pen blanks.

...nycubic resin funnel thingiverse small funnel fitting the anycubic resin bottles. does not have a snap fit, but neither to lose.

...resin vat drainer by jeeffi thingiverse resin vat drainer