Thingiverse
Donkey Car Dog Bone by AlexC-Makerologist
by Thingiverse
Last crawled date: 3 years, 5 months ago
On both the Desert Monster and Magnet RC cars the Dog Bones fall out all the time.
This is an attempt to replace the frequently lost dogbone linkage with a 3d print.
Designed to be printed in PET and ~ 3-4 walls, 50% infill, 0.4mm noz
1.5mm piano wire cut down to ~ 8mm length was used for the for the pins at the end of the dog bones. these holes will be uber snug and will require being tapped in with a hammer.
The part is designed to be snug, so a tiny bit of sanding may be needed especially at the ball ends. With wear, the part will loosen, Due to this I do not advise shrinking the part for a better early fit.
These are not quite as low friction as the original metal ones, so if you have a metal one on one side and a printed one on the other, the slip differential will take the path of least resistance, so its best if you are going to replace with these printed ones to do both the left and right of the same axel.
The pins at the ends are in parallel, due to print grain I do not advise turning the hole of one horizontal as that would put the shear load on the grain and part failure will be likely. if you want to reduce friction a little by having the ball end pins perpendicular, I have been tinkering with heating the dogbone with a hot air gun and then carefully twisting over the entire length.
This is an attempt to replace the frequently lost dogbone linkage with a 3d print.
Designed to be printed in PET and ~ 3-4 walls, 50% infill, 0.4mm noz
1.5mm piano wire cut down to ~ 8mm length was used for the for the pins at the end of the dog bones. these holes will be uber snug and will require being tapped in with a hammer.
The part is designed to be snug, so a tiny bit of sanding may be needed especially at the ball ends. With wear, the part will loosen, Due to this I do not advise shrinking the part for a better early fit.
These are not quite as low friction as the original metal ones, so if you have a metal one on one side and a printed one on the other, the slip differential will take the path of least resistance, so its best if you are going to replace with these printed ones to do both the left and right of the same axel.
The pins at the ends are in parallel, due to print grain I do not advise turning the hole of one horizontal as that would put the shear load on the grain and part failure will be likely. if you want to reduce friction a little by having the ball end pins perpendicular, I have been tinkering with heating the dogbone with a hot air gun and then carefully twisting over the entire length.
Similar models
thingiverse
free
Small hand cranked flashlight replacement crank parts by DonJuanito
...the original metal pin...
edit: uploaded v3.2
this version adds small slots in the pivot to enhance the click in position feeling
thingiverse
free
slot car replacement guide pin by rsteel02
...ot cars. i printed it in pla with a brim and supports enabled. it was a snug fit and i had to slightly ream out the screw hole.
thingiverse
free
TBS Immortal T replacment end caps read notes by Dronenation
...wing on the antenna then get a small peice of heat shrink and fit this then fit the caps.
stand upright to print for best results
thingiverse
free
dog bone for rc car just over 7cm by bazan
...dog bone for rc car just over 7cm by bazan
thingiverse
just over 7 cm rc car dogbone
thingiverse
free
BB Balance Wheel 1 by Tacblades
...me of about 10s
everything is a tight friction fit so you may have to trim the main pin hole and the pin edges to get a snug fit.
thingiverse
free
914 Middle Sun Visor Mount by 914Buff
...not need to do it to that level. i broke the first one when putting it into the car so be careful when putting the metal pins in.
thingiverse
free
Watch Buckle by LindsayFowler
...y, the latch part of the buckle did not break, so you can reuse it (they are hard to print, as they need to be small and strong).
thingiverse
free
Dog Cooler by b2vn
...um strength.
i have designed it to leave the door 100 mm open. i have uploaded the freecad file if any one wants another length.
thingiverse
free
Replacement Clip for Ugreen Bluetooth 5.0 Receiver by higglyblarg
...pin hole. i would recommend printing in petg or similar for longevity. i cleaned out the hole for the...
thingiverse
free
Window Blind Pull End by mpkarssen
...window blinds, so i drew up a replacement.
dimensions:
length - 27mm
narrow end - 9mm
widest point - 13mm
hole for string - 3.5mm
Makerologist
thingiverse
free
Makerologist Roboderby (donkey car mods) by AlexC-Makerologist
...esigned to hold the car up during calibration (designed for 2.7mm door skin).
http://www.makerologist.comhttps://www.myopen3d.com
thingiverse
free
50mm Fan Guard by AlexC-Makerologist
...thing:33779 + i added a dome over the motor center to smooth out the air flow a tiny bit, not that it matters much at this scale.
thingiverse
free
PrintrBot Power Tower Bearing Fastener by AlexC-Makerologist
...dirty modification of "
printrbot spool coaster bearing fastener" to make the clip work with the printrbot power tower.
thingiverse
free
Snap-together Cam Set for Strandbeest by AlexC-Makerologist
...his will help with the camshaft rigidity by reducing flex, which in turn makes the walker's movement more precise and smooth.
thingiverse
free
AC Twist On Cable Loops For 20mm Extrusion by AlexC-Makerologist
... (on 20 mm extrusion), and unlike zip ties these are re-usable!
print with 2-3 perimeters for best strength.
4 sizes included
thingiverse
free
AC PrintrBot LC v2 40mm Fan Mount by AlexC-Makerologist
...ent 40 mm fans, so i made this plate to have the correct holes for a 40 mm fan.
1 perimeter and 20% infill is more than enough.
thingiverse
free
Needle File Handle w/ Thumb Set Screw by AlexC-Makerologist
...for large hands. (no, its not parametric anymore, just expand the hole a tiny bit with a hot drill bit, if the files wont go in.)
thingiverse
free
AC Stack-On 17 Storage Box Removeable Divider by AlexC-Makerologist
... i have made temp dividers out of anything from cardboard to aluminum, but finally now the simplest solution, just print more! =)
thingiverse
free
Printrbot LC v2 Extruder Tension Plate With Nut-Lock by AlexC-Makerologist
...umber of tools needed to service the machine to a minimal. all i did was cut the part in half. but i like it allot more this way.
thingiverse
free
AC T-Nut Slider - 20mm Extrusion by AlexC-Makerologist
... did try more complicated handles, longer sticks, etc, they just get in the way. the k.i.s.s. mantra works very well here. enjoy!
Alexc
thingiverse
free
50mm Fan Guard by AlexC-Makerologist
...thing:33779 + i added a dome over the motor center to smooth out the air flow a tiny bit, not that it matters much at this scale.
thingiverse
free
PrintrBot Power Tower Bearing Fastener by AlexC-Makerologist
...dirty modification of "
printrbot spool coaster bearing fastener" to make the clip work with the printrbot power tower.
thingiverse
free
Snap-together Cam Set for Strandbeest by AlexC-Makerologist
...his will help with the camshaft rigidity by reducing flex, which in turn makes the walker's movement more precise and smooth.
thingiverse
free
AC Twist On Cable Loops For 20mm Extrusion by AlexC-Makerologist
... (on 20 mm extrusion), and unlike zip ties these are re-usable!
print with 2-3 perimeters for best strength.
4 sizes included
thingiverse
free
AC PrintrBot LC v2 40mm Fan Mount by AlexC-Makerologist
...ent 40 mm fans, so i made this plate to have the correct holes for a 40 mm fan.
1 perimeter and 20% infill is more than enough.
thingiverse
free
Needle File Handle w/ Thumb Set Screw by AlexC-Makerologist
...for large hands. (no, its not parametric anymore, just expand the hole a tiny bit with a hot drill bit, if the files wont go in.)
thingiverse
free
AC Stack-On 17 Storage Box Removeable Divider by AlexC-Makerologist
... i have made temp dividers out of anything from cardboard to aluminum, but finally now the simplest solution, just print more! =)
thingiverse
free
AC T-Nut Slider - 20mm Extrusion by AlexC-Makerologist
... did try more complicated handles, longer sticks, etc, they just get in the way. the k.i.s.s. mantra works very well here. enjoy!
thingiverse
free
Printrbot LC v2 Extruder Tension Plate With Nut-Lock by AlexC-Makerologist
...umber of tools needed to service the machine to a minimal. all i did was cut the part in half. but i like it allot more this way.
thingiverse
free
MO3D Octagonal Candle Holder by AlexC-Makerologist
...yopen3d!
https://www.myopen3d.comhttps://www.facebook.com/myopen3dhttps://www.instagram.com/myopen3d/https://twitter.com/myopen3d
Donkey
thingiverse
free
donkey by Syzguru11
...donkey by syzguru11
thingiverse
donkey
thingiverse
free
Donkey by Scottland
...d for use with a cnc machine and to be vacuum formed: http://www.instructables.com/id/donkey-mask-with-working-mouth-face-puppet/
thingiverse
free
Shrek Donkey by roy771216
...shrek donkey by roy771216
thingiverse
shrek donkey
thingiverse
free
Donkey scan by maiersbus
...donkey scan by maiersbus
thingiverse
i scanned this donkey some years ago from wood carved donkey.
thingiverse
free
donkey kong by zyzomys
...donkey kong by zyzomys
thingiverse
donkey kong by nintendo
thingiverse
free
donkey kong by zyzomys
...donkey kong by zyzomys
thingiverse
donkey kong by nintendo
thingiverse
free
Donkey Jetson by matthieurouif
...donkey jetson by matthieurouif
thingiverse
donkey plate to support both raspberry pi and jetson dev kit
thingiverse
free
Donkey Kong arcade by zyzomys
...donkey kong arcade by zyzomys
thingiverse
new donkey kong
thingiverse
free
Donkey 3D scan by ptobery
...donkey 3d scan by ptobery
thingiverse
donkey 3d scan
thingiverse
free
Donkey by Sensei
...donkey by sensei
thingiverse
object to hang on christmas tree or window.
Bone
thingiverse
free
bone bone by koun
...bone bone by koun
thingiverse
this is a bone
thingiverse
free
bone by Syzguru11
...bone by syzguru11
thingiverse
bone
thingiverse
free
bone by Dymaris99
...bone by dymaris99
thingiverse
dog bone
thingiverse
free
bone by Darkwolf
...bone by darkwolf
thingiverse
just a bone
thingiverse
free
hand-bone
...hand-bone
thingiverse
bones for a robot hand (palm)
thingiverse
free
Bone by Husebot
...bone by husebot
thingiverse
a bone with a little hole in the middle.
thingiverse
free
Bone Narwhal
...bone narwhal
thingiverse
a narwhal carved out of bone (jk sculpey) but still gnarly! a gnarwhal!
thingiverse
free
Skeleton with bone
...ith bone
thingiverse
skeleton attacking with bone. join me on my facebook grouphttps://www.facebook.com/groups/2416691938656528/
thingiverse
free
bone by kcannon__143
...bone by kcannon__143
thingiverse
thingiverse
free
fishing bone by menyiv
...fishing bone by menyiv
thingiverse
fishing bone
Dog
thingiverse
free
Dog
...dog
thingiverse
dog
thingiverse
free
dog
...dog
thingiverse
simple dog
thingiverse
free
dog
...dog
thingiverse
cool dog for wall decor lay flat scale to any size and enjoy.
thingiverse
free
dog by
...dog by
thingiverse
its a dog i made out of shapes and made with one letter t.
thingiverse
free
dog by Syzguru11
...dog by syzguru11
thingiverse
dog
thingiverse
free
Dog by Matthewkaye
...dog by matthewkaye
thingiverse
this is a dog.
thingiverse
free
Dog by Robertsm
...dog by robertsm
thingiverse
this is a dog
thingiverse
free
Dog by good54
...dog by good54
thingiverse
dog
thingiverse
free
dog by KoenKo
...dog by koenko
thingiverse
dog
thingiverse
free
dog by yuh1973
...dog by yuh1973
thingiverse
dog
Car
thingiverse
free
car
...car
thingiverse
cool car
thingiverse
free
car
...car
thingiverse
it is a car the wheels can turn
thingiverse
free
Car Radio Bracket for Mounting Car Stereo in Car
...o must be printed and attached to sides of stereo. holes may need to be modified. is designed to be modified to suit application.
thingiverse
free
48ft HO train car intermodal well car stack car container car by konrads3
...rads3
thingiverse
based on http://www.thingiverse.com/thing:670492 48ft ho train car intermodal well car stack car container car
thingiverse
free
car
...car
thingiverse
simple car shape i made in inventor. kinda looks like my hyundai
thingiverse
free
CAR
...car
thingiverse
volvo
thingiverse
free
car
...car
thingiverse
qweqwe
thingiverse
free
car by Syzguru11
...car by syzguru11
thingiverse
car
thingiverse
free
For a car by Rustam
...for a car by rustam
thingiverse
for a car
thingiverse
free
Car by DawgDodger
...car by dawgdodger
thingiverse
car