Thingiverse
DobleMosfetMKS by Cristian3egnarDi
by Thingiverse
Last crawled date: 2 years, 11 months ago
installing the mks base 1.3 board I had to rearrange the position of the two mosfets so I remixed an existing project and ready to be installed in the back of the frame also exploiting the same screws that join the frame.
Similar models
cg_trader
$9
Roof installation frame
...ation frame for installing a banner (without a banner) metal frame with weights for wind exposure, installation on a flat surface
grabcad
free
M72 Motorcycle project Frame Assembly
...7 the frame for this project . will load the frame files after i have installed the engine/gearbox, in case of minor adjustments.
thingiverse
free
SPC 95X FPV VTX Canopy by kmmcca
...mall (1.5mm) hole drilled in the frame to accommodate a screw.
best if printed upside down. may need supports for the screw tabs.
grabcad
free
bulldozer tire
...dozer tire
grabcad
the metal frame is installed on the metal x and the rubber frame is installed on it for the komachi bulldozer
thingiverse
free
filament guide on printer frame by Supkompot
...lling the direct filament feed, i needed an oval guide that would not hinder the carriage travel. easy to install, easy to print.
thingiverse
free
Lerdge display frame for Prusa Steel clone
...anel, so part which i designed has a bezel with the 2 mm height on the back side. that's why supports is needed for printing.
3dwarehouse
free
installation frame
...installation frame
3dwarehouse
thingiverse
free
Lithophane Picture Frame by GingerTwin57
...e led strip inside the back piece, install your 1501007.5mm lithophane and attach the frame with 4 screws. its as simple as that!
grabcad
free
Frame 1
...frame 1
grabcad
this is a frame. it was install in the modern shop koma.
3dwarehouse
free
instalation frame+toilet
...instalation frame+toilet
3dwarehouse
Cristian3Egnardi
thingiverse
free
Pegboard_ikea_fixa by Cristian3egnarDi
...pegboard_ikea_fixa by cristian3egnardi
thingiverse
created for drill ikea fixa
thingiverse
free
Pegboard_boxlacher by Cristian3egnarDi
...oard_boxlacher by cristian3egnardi
thingiverse
suitable for a panel with a 5mm diameter hole, it houses up to a diameter of 65mm
thingiverse
free
Pegboard_screwdrivers by Cristian3egnarDi
...le for a panel with a 5mm diameter hole, the 3 holes are diameter 9mm to accommodate 3 mini screwdrivers or others of your choice
thingiverse
free
film Stretch / Film estensibile by Cristian3egnarDi
...film stretch / film estensibile by cristian3egnardi
thingiverse
film stretch holder
thingiverse
free
Opel Mokka Car Cap by Cristian3egnarDi
...opel mokka car cap by cristian3egnardi
thingiverse
car cap for opel mokka 2014
thingiverse
free
mother board MKS Tatara frame by Cristian3egnarDi
...mother board mks tatara frame by cristian3egnardi
thingiverse
mks base v.1
thingiverse
free
MKS TFT32 Tatara Frame by Cristian3egnarDi
...ay mount for tatara frame, i have inserted 4 hole compatible
edit: i have a second version with the slimmer fixing base (redux)
thingiverse
free
Spool Frame sx Anet A8 by Cristian3egnarDi
...or mounted on the right frame. there are three files: spool holder, nut and coil adapter. the best solution for mobile stuva ikea
thingiverse
free
JGAURORA A5 TUBE mount Plugandplay by Cristian3egnarDi
...ed the part that was weak as requested by some of you, i could not test no longer having the printer but i wait for your feedback