Thingiverse
Deadbolt Combination Lock by DuaneIndeed
by Thingiverse
Last crawled date: 3 years ago
This is a combined combination lock and a deadbolt.
The three cylinders rotate smoothly on simple gear bearings; with 1 of 17,576 possible unlock combinations. Once unlocked, the lock slides out of the bolt-keep.
Crack-resistant - Each cylinder has 25 blind partial (false) lock pin channels, and one blind full (true) lock pin channel. All cylinders must align to the correct combination to fully pass the lock pin.
Mount the lock (left side, or right side) on a door that opens-in, or opens-out. Two versions of a Bolt Keep are provided: one model that mounts on a plane that is parallel to the door, and another model that mounts perpendicular to the door plane (e.g. on a door jamb that faces the lock).
Usage
• The lock has three sliding positions: Locked, Open (middle position), and Remove. The cylinders may be randomly rotated while in any of these positions to hide the unlock combination.
• Set the cylinders to the unlock combination to allow the lock to slide from the Locked to the Open position (or Open to Locked position). Rotate the cylinders randomly to prevent the lock from sliding into the Locked or Open position.
• Set the cylinders to the unlock combination, then rotate all cylinders 180 degrees, to allow the lock to slide from the Open to the Remove position. Slide the lock fully away from Bolt Keep, until the lock may be lifted from the door mounting plate.
Build
• Printable on a 120mm build plate.
• Assembled dimensions of the lock (not including the Bolt Keep): 4.9cm (thick), 15.4cm (length), 9cm (wide).
• The Door Plate and Bolt Keep are intended to be installed on the same plane. For installations where the surfaces of the door and door jamb are not on the same plane, separate adjustable mounting spacer models are provided for the Door Plate and for the Bolt Keep. There are two “flat” spacer models, one for each of the Bolt Keep and the Door Plate. There is a third “angled” spacer for the Bolt Keep, which is intended to be used in situations where there is door molding with an angled surface. All spacers are supplied at 1mm thick. Use a Slicer to apply the needed scaling in the Z axis to print the desired spacer thickness that will provide the offset necessary to position the Door Plate and the Bolt Keep on the same plane.
Parts Lists
M3x25 Socket Cap bolts, in stainless steel (qty 4) https://www.boltdepot.com/Product-Details.aspx?product=6384
M3x16 Socket Cap bolt, in stainless steel (qty 1) https://www.boltdepot.com/Product-Details.aspx?product=6382
M3 nuts (qty 5) https://www.boltdepot.com/Product-Details.aspx?product=4773
Loctite Super Glue Ultra Gel Control, for PLA. http://a.co/gHkket5 Follow the glue label instructions exactly! [Refer to the youtube video by H Alex "How to glue PLA" showing his research in finding the best glue for PLA]. For ABS, use an acetone-ABS slurry to weld parts together.
Mounting hardware:
#6 wood screw (qty 4) https://www.boltdepot.com/Product-Details.aspx?product=3955
#8 wood screw (qty 2) https://www.boltdepot.com/Product-Details.aspx?product=3961
Print Instructions
All parts print at 0.2mm line height, with 50% infill.
Supports are NOT required, except for two parts. These parts require supports: CylinderOuter_Indicator, and CylinderMiddle_Indicator.
Print all parts in the orientation as supplied in their respective models.
Print List
Small Gear (x 12)
Gear Spacer Plate (x 2)
Gear Frame (x 1)
Cylinder Outer, Part A (x 1)
Cylinder Outer Indicator Ring (x 1)
Cylinder Middle, Part A (x 1)
Cylinder Middle, Part B (x 1)
Cylinder Middle Indicator Ring (x 1)
Cylinder Inner, Part A (x 1)
Cylinder Inner, Part B (x 1)
Cylinder Inner Indicator Ring (x 1)
Cap (x 1)
Door Plate (x 1)
Case (x 1)
Case Top (x 1)
Bolt (x 1)
Bolt Keep (or Bolt Keep 90) (x 1)
Door Plate Spacer (optional)
Bolt Keep Spacer (optional)
Bolt Keep Angled Spacer (optional)
The three cylinders rotate smoothly on simple gear bearings; with 1 of 17,576 possible unlock combinations. Once unlocked, the lock slides out of the bolt-keep.
Crack-resistant - Each cylinder has 25 blind partial (false) lock pin channels, and one blind full (true) lock pin channel. All cylinders must align to the correct combination to fully pass the lock pin.
Mount the lock (left side, or right side) on a door that opens-in, or opens-out. Two versions of a Bolt Keep are provided: one model that mounts on a plane that is parallel to the door, and another model that mounts perpendicular to the door plane (e.g. on a door jamb that faces the lock).
Usage
• The lock has three sliding positions: Locked, Open (middle position), and Remove. The cylinders may be randomly rotated while in any of these positions to hide the unlock combination.
• Set the cylinders to the unlock combination to allow the lock to slide from the Locked to the Open position (or Open to Locked position). Rotate the cylinders randomly to prevent the lock from sliding into the Locked or Open position.
• Set the cylinders to the unlock combination, then rotate all cylinders 180 degrees, to allow the lock to slide from the Open to the Remove position. Slide the lock fully away from Bolt Keep, until the lock may be lifted from the door mounting plate.
Build
• Printable on a 120mm build plate.
• Assembled dimensions of the lock (not including the Bolt Keep): 4.9cm (thick), 15.4cm (length), 9cm (wide).
• The Door Plate and Bolt Keep are intended to be installed on the same plane. For installations where the surfaces of the door and door jamb are not on the same plane, separate adjustable mounting spacer models are provided for the Door Plate and for the Bolt Keep. There are two “flat” spacer models, one for each of the Bolt Keep and the Door Plate. There is a third “angled” spacer for the Bolt Keep, which is intended to be used in situations where there is door molding with an angled surface. All spacers are supplied at 1mm thick. Use a Slicer to apply the needed scaling in the Z axis to print the desired spacer thickness that will provide the offset necessary to position the Door Plate and the Bolt Keep on the same plane.
Parts Lists
M3x25 Socket Cap bolts, in stainless steel (qty 4) https://www.boltdepot.com/Product-Details.aspx?product=6384
M3x16 Socket Cap bolt, in stainless steel (qty 1) https://www.boltdepot.com/Product-Details.aspx?product=6382
M3 nuts (qty 5) https://www.boltdepot.com/Product-Details.aspx?product=4773
Loctite Super Glue Ultra Gel Control, for PLA. http://a.co/gHkket5 Follow the glue label instructions exactly! [Refer to the youtube video by H Alex "How to glue PLA" showing his research in finding the best glue for PLA]. For ABS, use an acetone-ABS slurry to weld parts together.
Mounting hardware:
#6 wood screw (qty 4) https://www.boltdepot.com/Product-Details.aspx?product=3955
#8 wood screw (qty 2) https://www.boltdepot.com/Product-Details.aspx?product=3961
Print Instructions
All parts print at 0.2mm line height, with 50% infill.
Supports are NOT required, except for two parts. These parts require supports: CylinderOuter_Indicator, and CylinderMiddle_Indicator.
Print all parts in the orientation as supplied in their respective models.
Print List
Small Gear (x 12)
Gear Spacer Plate (x 2)
Gear Frame (x 1)
Cylinder Outer, Part A (x 1)
Cylinder Outer Indicator Ring (x 1)
Cylinder Middle, Part A (x 1)
Cylinder Middle, Part B (x 1)
Cylinder Middle Indicator Ring (x 1)
Cylinder Inner, Part A (x 1)
Cylinder Inner, Part B (x 1)
Cylinder Inner Indicator Ring (x 1)
Cap (x 1)
Door Plate (x 1)
Case (x 1)
Case Top (x 1)
Bolt (x 1)
Bolt Keep (or Bolt Keep 90) (x 1)
Door Plate Spacer (optional)
Bolt Keep Spacer (optional)
Bolt Keep Angled Spacer (optional)
Similar models
thingiverse
free
Pixel Strip Bushing
...ps://www.boltdepot.com/metric_socket_button_head...
m4 fender washer -https://www.boltdepot.com/product-details.aspx?product=7313
thingiverse
free
Mixing Tank by Exige9000
...ww.amazon.com/s?ie=utf8&field-keywords=r188&index=blended&link_code=qs&sourceid=mozilla-search&tag=mozilla-20
thingiverse
free
Wyze Lock Spacer Plate by mrhill_icb
...yze body will stand off and wobble around. with this spacer plate the wyze lock can be mounted flush and tight on a flat surface.
thingiverse
free
Wyze Lock Spacer Plate by mrhill_icb
...yze body will stand off and wobble around. with this spacer plate the wyze lock can be mounted flush and tight on a flat surface.
thingiverse
free
Nordictrack T6.7S Treadmill Tablet Holder
...-8 (a-2), 4mm (https://www.boltdepot.com/product-details.aspx?product=4514)
print qty 2 brackets and qty 1 of the holder. enjoy..
thingiverse
free
Pixel Strip Bushing
...on_head_stainless_steel_18-8_(a-2)_4mm_x_0.7mm.aspx
m4 fender washer -https://www.boltdepot.com/product-details.aspx?product=7313
thingiverse
free
Display-Aligned Hinge Mounts (EyeGaze & More) by atmakers
...uct=4802
in either case, we found it best to insert neoprene washers to help the flat side of the screw to help it gain friction.
grabcad
free
Door Lock
...s lock can be adapted to fit keypad locks or norman doors.
this resigned challenge was made by austin coleman and tyler buchan
thingiverse
free
Sliding Bolt Spacer by kalazzerx
... door jamb.
sliding bolt is standard household size - about 1 1/2" x 3" (including the receiver which i did not use).
thingiverse
free
Wire Shelf Tool Holders and Brackets by skelo
...olt: https://www.boltdepot.com/product-details.aspx?product=9625
nut: https://www.boltdepot.com/product-details.aspx?product=4107
Duaneindeed
thingiverse
free
Art Deco Printer Enclosure by DuaneIndeed
...the design is meant to be simple, functional, and interesting. i used acrylic sheets and atomic filament’s petg for this build.
thingiverse
free
Cat Litter Box Door Mat by DuaneIndeed
...inted this in petg. infill 45%, 2 perimeters, 3 layers top/bottom. spray it with sealant to make it easier to keep it sanitary.
thingiverse
free
Trowel Bottle Opener by DuaneIndeed
...and one without text.
this model requires that the us penny be added during the print process.
2.38 cm h x 5.41cm w x 12.41 cm l.
thingiverse
free
Snow Cone Molds and Cups by DuaneIndeed
...star.
if you'd rather use disposable paper cups, the cone mold is compatible with sno-kone brand cups: http://a.co/d/blcf3cb
thingiverse
free
Garment Door Hanger by DuaneIndeed
...as no name plate.
i printed one of these for each bridesmaid of a bridal party. i customized each with the name of a bridesmaid.
thingiverse
free
Post Bracket for a Frontgate Solar Panel by DuaneIndeed
... post stake, and is bolted onto the original bracket on the back of the panel.
i printed this with abs, 50% infill, 0.2mm layers.
thingiverse
free
Tuxedo Cufflink and Stud Holder Box by DuaneIndeed
...ngest part is 12 cm long.
i added hugger-fins to the inner trays in my second version. the hugger-fins make it much more rugged.
thingiverse
free
Turkey Lacer Pins and String Holder Caddy by DuaneIndeed
... pins: a stray pin poking out from within a garbage bag, or lodged in your sink drain (business end up) can really ruin your day.
thingiverse
free
Critter Rescue Ramp by DuaneIndeed
...a cord to the anchor tabs at the top corners of the ramp; and tie the other end of the cord to a suitable pool edge anchor point.
thingiverse
free
Iphone 7Plus, 7, and 6 Tripod Adapter for Timelapse by DuaneIndeed
... and it supports a range of different mount configurations.
i printed this and i have used it several times without any issues.
Deadbolt
3ddd
free
Kwikset / SmartCode Deadbolt
...kwikset / smartcode deadbolt
3ddd
kwikset , замок
kwikset smartcode deadbolt
3d_sky
free
Kwikset SmartCode/Deadbolt
...kwikset smartcode/deadbolt
3dsky
castle
kwikset smartcode deadbolt
thingiverse
free
Deadbolt Lock Mount by scoot13
...dard doorway to mount a deadbolt lock on. you can use it to practice lock-picking, or just as a function test for your deadbolts.
thingiverse
free
Deadbolt Combination Lock by TechAutist
...deadbolt combination lock by techautist
thingiverse
thingiverse
free
deadbolt grill bucket mount by Thorlax
...deadbolt grill bucket mount by thorlax
thingiverse
rear section for mounting axial light buckets on my deadbolt grill.
thingiverse
free
SCX-10 Deadbolt front lights by Hairless_Ewock
...scx-10 deadbolt front lights by hairless_ewock
thingiverse
this is a lens fab for scx-10 deadbolt
thingiverse
free
Wyze Sense Deadbolt Bracket
...?ref=shop_home_active_1
and while you are there look at my other brackets.
check out the video here:
https://youtu.be/-sctyiw0bt0
thingiverse
free
Deadbolt Cover by Fox01
...i know i could replace the door handle with a knob but using the printer is move fun and unique. i like thinking outside the box.
thingiverse
free
Deadbolt (Cerrojo) by jia
...do" and "cerrojo2-girado" are to increase resistance
the file cerro2-rotated must be printed with support material
thingiverse
free
axial deadbolt grill (ventilated) by Thorlax
...axial deadbolt grill (ventilated) by thorlax
thingiverse
ventilated version.
Lock
turbosquid
$1
Lock
...ck
turbosquid
royalty free 3d model lock for download as fbx on turbosquid: 3d models for games, architecture, videos. (1286851)
3d_export
$5
lock handle
...lock handle
3dexport
lock handle
3d_export
$5
hinged lock
...hinged lock
3dexport
hinged lock
turbosquid
$1
Lock Box with combination lock
...ee 3d model lock box for download as 3ds, obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1215494)
turbosquid
$2
Lock
...
royalty free 3d model lock for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1452660)
turbosquid
$35
Lock
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$24
lock
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Lock
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$6
Lock
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$4
Lock
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Combination
3d_export
$15
combine harvester
...combine harvester
3dexport
combine harvester.hope you like it!<br>formats..max.fbx.obj.3ds
turbosquid
$9
COMBINATION PADLOCK
...royalty free 3d model combination padlock for download as max on turbosquid: 3d models for games, architecture, videos. (1485626)
turbosquid
$24
The Combination Padlock
... 3d model the combination padlock for download as c4d and fbx on turbosquid: 3d models for games, architecture, videos. (1668991)
turbosquid
$10
Combination Padlock
...free 3d model combination padlock for download as max and obj on turbosquid: 3d models for games, architecture, videos. (1340019)
3d_export
$10
modern ornament combination
...modern ornament combination
3dexport
modern ornament combination
turbosquid
$35
Combine Harvester
...d model combine harvester for download as blend, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1646743)
turbosquid
$19
Combination for climbing
...el combination for climbing for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1601482)
turbosquid
$3
Combination Pliers
... 3d model combination pliers for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1393273)
3d_export
$10
modern sofa combination
...modern sofa combination
3dexport
modern sofa combination vr4.1
3d_export
$5
beet combine harvester
...beet combine harvester
3dexport
beet combine harvester step