D810 Effector by WhiteTiger13

...ctor as the original, and uses the original fan. just gives better aerodynamics, and is out of the way for working on the hot-end

...15 blower type fan (optional) i designed the effector for my zonestar d810, but it should fit any kossel (~20x30cm build volume).

...brisa d810 base plana 3dwarehouse

...brisa d810 base madeira 3dwarehouse

...r 2 cooling fans by sonnydr thingiverse this is a new hotend carriage for the zonestar d810 3d printer to hold two cooling fans.

...tetiger13 thingiverse belt holder and tensionner for zonestar d810. v0.1 may contain errors contain hi-poly and low-poly version

...d kurt’s d810 vise has a large 10" jaw opening and provides up to 11,600 lbs. of clamping force. file downloaded from kurt.

...model 711 3dsky chair modern size: w713 d810 h770

...модель 711 3ddd fredrik kayser размер: w713 d810 h770

...effector by olo2000pm thingiverse effector

...18650 4х3.7v serial connection by whitetiger13 thingiverse case for 4x18650 serial connection

...1.75mm filament filter case by whitetiger13 thingiverse filament dust filter case. no support needed.

...tetiger13 thingiverse belt holder and tensionner for zonestar d810. v0.1 may contain errors contain hi-poly and low-poly version

...150 mm/6-inch electronic digital caliper stand by whitetiger13 thingiverse this is wall holder for 150mm digital caliper

...0 profile by whitetiger13 thingiverse you will need 2xm3 bolts , 2xm3 nuts and a 1.75 mm filament tube (2mm inner, 4mm diameter)

...entred 15mm. solidworks source file added in case of a certain interest to this model, i added the source file of solidworks 2016

...делал для себя, но если кому ещё пригодится, то буду очень рад. за базу для установки взята подставка для arduino от jimmyvargas.

...ие к безщеточному движку a2212 центральное крепление было переработано под печать 0,8 соплом а точнее под ширину экструзии 0,88мм

...модель 711 3ddd fredrik kayser размер: w713 d810 ...

...pollock chair 3ddd julian chichester , pollock w810 x d810 x h700 seat...

...ctor as the original, and uses the original fan. just gives better aerodynamics, and is out of the way for working on the hot-end

...tetiger13 thingiverse belt holder and tensionner for zonestar d810. v0.1 may contain errors contain hi-poly and low-poly version

...r 2 cooling fans by sonnydr thingiverse this is a new hotend carriage for the zonestar d810 3d printer to hold two cooling fans.

... labels underneath each button (need to print on a good flat bed for these to be legible) added labels on the top of each button.

...nto the 2020 rail, so that a single mount at one end will still hold the lcd horizontal. the same item can be used at either end.

...and with a m3 screw and nut to the 2020 aluminium extrusion. you need to print the part six times, half of that must be mirrored.

...art of the strengthening, this incorporates one of the sets of spacers into the part, which makes it a little easier to assemble.

...e spheres will expand with your song. fully customisable, change the color, the size of the spheres or even put in different s...

...mograph compatible (you can effect the pieces with mograph effector) - included also a non-mograph version with...

...effector by olo2000pm thingiverse effector

...cerambot-effector thingiverse cerambot-effector

...ulize effector by candyasdf thingiverse mount things on effector with m3 screws effector radius : 25.4mm rod arm distance : 40mm

...delta effector by zavier thingiverse delta effector with radial fan 50 and bltouch

...effector for delta printer thingiverse effector for delta printer (3 color) using diamond hotend

...delta effector magnetic by fpassos thingiverse effector for e3dv6 hotend. i needed put the spheres (10mm) on the effector.

...end effector gripper thingiverse end effector gripper for a robotic arm uses mg995 servo motor