Thingiverse
Cuvette Spinner by IIIStarkIII
by Thingiverse
Last crawled date: 3 years, 5 months ago
This is a cuvette spinner designed to be used in conjunction with a hex driver and electric drill to clear out fluids from cuvettes using centrifugal force. Sucessfully tested up to 2000 RPM. Above that and your mileage may vary.
Press fit the hex driver into the centers, and insert four M3 bolts through to lock it all down.
When done printing, use a heat gun or similar tool to put a slight upward bend into the four tabs. This will give the cuvette clips much better grip.
The cuvette should be a tight snap fit into the slot, and you should be able to both insert and remove it without taking the two halves apart.
Press fit the hex driver into the centers, and insert four M3 bolts through to lock it all down.
When done printing, use a heat gun or similar tool to put a slight upward bend into the four tabs. This will give the cuvette clips much better grip.
The cuvette should be a tight snap fit into the slot, and you should be able to both insert and remove it without taking the two halves apart.
Similar models
thingiverse
free
Hex Driver Holder by JohnWaly
... driver holder by johnwaly
thingiverse
hex driver holder. fits my banggood hex drivers. will probably fit other brands. enjoy :)
thingiverse
free
Spectroelectrochemical cuvette insert by jbrisendine
...s is an .stl file for an electrode holder that fits inside a standard 1 cm square cuvette for spectroelectrochemical experiments.
thingiverse
free
Mini Hex Driver by j_jaarsma
...mini hex driver by j_jaarsma
thingiverse
a single wing hex driver to fit in small spaces.
thingiverse
free
Lobed Fidget Spinner by gregrjohnson
.... it accepts 608 bearings in its holes. bearings should be a tight friction fit. they may be difficult to insert, but will go in.
grabcad
free
Hex Driver Rack
...hex driver rack
grabcad
t- handle hex driver rack. 0.25" acrylic construction. with small insert tool holder racks on sides
thingiverse
free
Hex driver caddy by Sneezy3D
...
should fit any driver handle of 19mm or less.
if you printer tends to print undersized holes then up-scale the stl by a few %.
thingiverse
free
Sawblade Fidget Spinner by KhakiSlurry
...the printer for another week. uses standard 608zz bearing.
should fit a 1/4" hex nut.
the most dangerous spinner out there.
thingiverse
free
Waterpump
...e four m2x25 flathead screws, four m2 hex nuts and eight fitting washers.
can be upscaled easily to fit your particular use case.
thingiverse
free
1/2 - 13 Nut Inserts Thread with slot for screwdriver by paultyrer
...crewdriver by paultyrer
thingiverse
these inserts screw into a 1/2-13 nut using the screw driver slot.
great for fidget spinners
thingiverse
free
TBS Sexy Driver Holder by pdonszelmann
...workbench. holes are 20mm wide so should also fit similar hex tools as well. used white marker to highlight...
Cuvette
thingiverse
free
Cuvette holder / rack (10 cuvettes) by vsaggiomo
...r 10 cuvettes.
it prints easily without support or raft
tutorial on how to design it: https://www.youtube.com/watch?v=de253fmf7rs
thingiverse
free
Cuvette adapter by Chemist
...cuvette adapter by chemist
thingiverse
this is a adapter for use of cuvettes with 4 mm width in a normal cuvette slot.
thingiverse
free
cuvette rack by Phokas
...cuvette rack by phokas
thingiverse
cuvette rack
thingiverse
free
Standard cuvette by Dr_MCeeP
...standard cuvette by dr_mceep
thingiverse
a model of a standard cuvette.
thingiverse
free
Cuvette by seedwire
... ports permit an excitation beam to enter and fluorescence to be collected at 90deg.
this fits a 12.5mm x 12.5mm cuvette holder.
thingiverse
free
Cuvette Holder by aegorsuch
...cuvette holder by aegorsuch
thingiverse
holds a cuvette for a spectral project i made.
thingiverse
free
Cuvette holder by Seosamh
... got a new spectrophotometer, but it wouldn't hold the 50mm. cuvettes we had, so we just designed and 3d printed our own one.
thingiverse
free
Standard 3.5mL Cuvette by tcmartin24
...ndard 3.5ml cuvette by tcmartin24
thingiverse
3.5ml plastic cuvette. i modeled it to design a device that can contain a cuvette.
thingiverse
free
Cuvette Holder by bobthechemist
...holder by bobthechemist
thingiverse
a simple cuvette holder which was designed to assist students in creating a diy colorimeter.
thingiverse
free
Cuvette Rack by cmaschan
...tand stably on the bench. it is desirable to have a holder to avoid toppling. this holder can hold 8 cuvettes at the same time.
Spinner
turbosquid
$5
Spinner
...turbosquid
royalty free 3d model spinner for download as max on turbosquid: 3d models for games, architecture, videos. (1190412)
turbosquid
$1
Spinner
...turbosquid
royalty free 3d model spinner for download as dwg on turbosquid: 3d models for games, architecture, videos. (1173525)
3d_export
$5
spinner toy
...spinner toy
3dexport
cool spinner toy.
turbosquid
$12
Spinner
...id
royalty free 3d model spinner for download as max and obj on turbosquid: 3d models for games, architecture, videos. (1242592)
turbosquid
$20
Spinner
...lty free 3d model spinner for download as obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1191800)
turbosquid
$15
spinner
...yalty free 3d model spinner for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1165932)
turbosquid
$2
Spinner
...oyalty free 3d model spinner for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1187750)
turbosquid
free
Spinner
...lty free 3d model spinner for download as obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1230908)
turbosquid
$29
spinner
... free 3d model spinner for download as 3ds, obj, c4d, and fbx on turbosquid: 3d models for games, architecture, videos. (1471160)
turbosquid
$4
Spinner
...y free 3d model spinner for download as ma, max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1201076)