Thingiverse
cncDIY by tonyhoang
by Thingiverse
Last crawled date: 3 years, 1 month ago
The cncmini, I called tCNC :D
Body size: 45x45x30 (cm)
Work area: 14x14x3 (cm)
13 parts can printed (see in Assembly1.pdf)
4 rod 8mm, 40cm
2 rod 8mm, 10cm
12 lm8uu
4 thread rod 16mm, 45cm (with 20 bolt nut)
4 thread rod 8mm, 15cm
2 thread rod 8mm, 20cm
2 Lead Screw Rod 8mm-30cm + 4 Flange Brass Nut (X,Y axis)
1 Lead Screw Rod 8mm-10cm+ 2 Flange Brass Nut (Z axis)
3 Shaft Coupling (5mm-8mm)
3 stepper motor (I use nema 17).
1 775 motor 12-24v DC
1 ER11 + 3.175mm collet
1 Arduino Uno R3
1 Arduino CNC Shield
3 A4988
1 Relay (on/Off spindle)
And something you need to assembly.
Firmware: grbl v0.9j
Control: GrblControl
Body size: 45x45x30 (cm)
Work area: 14x14x3 (cm)
13 parts can printed (see in Assembly1.pdf)
4 rod 8mm, 40cm
2 rod 8mm, 10cm
12 lm8uu
4 thread rod 16mm, 45cm (with 20 bolt nut)
4 thread rod 8mm, 15cm
2 thread rod 8mm, 20cm
2 Lead Screw Rod 8mm-30cm + 4 Flange Brass Nut (X,Y axis)
1 Lead Screw Rod 8mm-10cm+ 2 Flange Brass Nut (Z axis)
3 Shaft Coupling (5mm-8mm)
3 stepper motor (I use nema 17).
1 775 motor 12-24v DC
1 ER11 + 3.175mm collet
1 Arduino Uno R3
1 Arduino CNC Shield
3 A4988
1 Relay (on/Off spindle)
And something you need to assembly.
Firmware: grbl v0.9j
Control: GrblControl
Similar models
cg_trader
$3
Pitch 8mm | 3D
... 3mm lead 4mm 8mm 10mm 1 14mm brass screw nut 8mm t8 lead screw stepper motor threaded rod screw flange for cnc 3d printer parts
thingiverse
free
5mm to 8mm Z axis shaft coupler by mrice
...ible shaft couplers on z axis rods, for 5mm motor shafts and 8mm threaded rods. use two m3x10mm screws and nuts to tighten down.
thingiverse
free
CoreXY Z Axis Carriage for Delrin nut (4 hole, 8mm lead screw) by Sean_c_roberts
...tl.
i added m3 screw holes on both the top and the bottom so you can choose to put the nut on top (pull) or on the bottom (push).
thingiverse
free
Z Axis Nut Mount 8mm Traped Nut by Nitrogen777
...uld use stainless steel threaded rod and a steel nut.
this will stop the two binding also the nut will wear not the threaded rod.
grabcad
free
Lead screw nut TR8x8
...ezoidal lead screw nut has a diameter of 8mm, lead 8mm,a pitch of 2mm and 4 thread starts.
material: brass
fixing holes: 2x m3
thingiverse
free
Nut block for 8mm threaded rod
...ore than 8mm long.
the threaded insert version uses three m365 threaded inserts. they are 6mm long with an outer diameter of 5mm.
thingiverse
free
350W wheelchair adapter by checkerz4456
...ded rods, 2 (6" x 1/4") threaded rods, 12 bolts for the rods, two 2" wall screws, and two 3 1/2" wall screws.
thingiverse
free
IMA-GO mini 3D Printer by gunawansy
... 8mm x 250mm x 2 y axis
4 8mm x 159mm x 1 x support
5mm threaded rods
1 5mm x 209mm x 2 z motor
belt x: 60cm
belt y: 52cm
grabcad
free
Lead Screw Nut - Threaded with Flange - 8mm Diameter 2mm Pitch
...mm threaded bore with a 2mm pitch. it is part of my complete 3d printer design and build project using only open source software.
thingiverse
free
Z axis system for CoreXY printer 5mm rod & lm12uu bearing by smeric
...-printer-thsl-500-8d-t-type-stepper-motor-lead-screw-dia-8mm-thread-8mm/32465980465.html ) so maybe you can use it too..
regards
Tonyhoang
thingiverse
free
Chopsticks & spoon containers by tonyhoang
...chopsticks & spoon containers by tonyhoang
thingiverse
a gift for my wife by 3d printer :)
thingiverse
free
28/8/2018: Updated: 3d filament holder by tonyhoang
...dated: 3d filament holder by tonyhoang
thingiverse
more smoothly and lightly to rolling
2 parts.
2 608 bearing.
1 threat rod 8mm