Thingiverse
Chipsticks v2 by snackeater22
by Thingiverse
Last crawled date: 3 years ago
This is the v2 after less than 24 hours posting of v1. It should be much better when used to pick small and light snacks like potato chip, beans, French fries, etc.
Learnt from v1 that the tabs at the back of the fingers are not needed. Removing it makes a clean design.
Learnt from v1 that the tabs at the back of the fingers are not needed. Removing it makes a clean design.
Similar models
grabcad
free
Electromagnetic magnet box V2 v1
...electromagnetic magnet box v2 v1
grabcad
electromagnetic magnet box v2 v1
grabcad
free
Antweights
...antweights
grabcad
motora v1, v2 and kabaré v1
thingiverse
free
Ummagawd Remix V1 V2 Hero 8 Mount
...ummagawd remix v1 v2 hero 8 mount
thingiverse
will fit v1 and v2. 35 deg. print in tpu
cg_trader
$6
Kyber Network Crystal v2 Coin v1 002
...kyber network crystal v2 coin v1 002
cg trader
kyber network crystal v2 coin v1 002
cg_trader
$6
Kyber Network Crystal v2 Coin v1 001
...kyber network crystal v2 coin v1 001
cg trader
kyber network crystal v2 coin v1 001
cg_trader
$34
Ultraman Agul V1 V2 SV 3D printable helmet | 3D
...rader
ultraman agul v1 v2 sv 3d printable helmet, for v1 and v2 its same, and now agul has his own supreme version (sv) form too
grabcad
free
Throttle / Gas Pedal Challenge v1 & v2
.../ gas pedal challenge v1 & v2
grabcad
gas pedal v1 and v2,
different is just the mounting plate to lower production costs.
3dwarehouse
free
厨房 v2
...厨房 v2
3dwarehouse
v1
grabcad
free
Camera_mount_S2023 v1-v2
...camera_mount_s2023 v1-v2
grabcad
epics
cg_trader
$12
Harpy V1 and V2 | 3D
...2 | 3d
cg trader
this contains v1 and v2 from this figure, it was part of another kickstarter project i finished a few weeks ago
Chipsticks
thingiverse
free
Chipsticks by snackeater22
...ks as it works like chopsticks which is dedicated for snacks like potato chips. but i later found that it is the name of a snack.
thingiverse
free
Disposable chopsticks cutting test for iModela by mah_digilife
...test for imodela by mah_digilife thingiverse this is disposable chipsticks cutting test for imodela. the size of the moai...
cg_trader
free
CHEAP NOODLES STORE
... other interior shop cafe restaurant cafe interior cafe interior coffee shop restaurant interior restaurant kitchen shop interior
Snackeater22
thingiverse
free
Knife Holder by snackeater22
...is required.
note that the uploaded design is slightly different with the chinese character modified to eliminate the weak point.
thingiverse
free
Spiralled Self Watering Planter - Remix by snackeater22
...thingiverse
i would like it shorter so here is the remix.
if you make it, please post a make. your support is highly appreciated
thingiverse
free
Chipsticks by snackeater22
...ks as it works like chopsticks which is dedicated for snacks like potato chips. but i later found that it is the name of a snack.
thingiverse
free
Modern Bucket (Printed in Vase Mode) by snackeater22
...attern. the complex pattern makes the printout rigid. i need a bucket/bin, so i remixed it and the result is great.
180x180x180mm
thingiverse
free
Bag Clip - Clothespin Remix by snackeater22
...h, so softer springs are provided. springs are compatible with my previous remix below.
https://www.thingiverse.com/thing:4877171
thingiverse
free
Latching Broom Holder - Filament as Hinge Pin by snackeater22
...bout 1.9mm so that i can use a short filament as the hinge pin. i put a drop of uv glue to one end of the pin to fix it in place.
thingiverse
free
Single PS4 Pro Controller Mount with cable hole by snackeater22
...and make the cable hole bigger. the one i printed with silk pla was broken so i thicken the area near the cable hole with fillet.
thingiverse
free
Playstation Platinum Wireless Headset Hinge Fix by snackeater22
...ted fix should fit tightly and can even be use with screws. if it is too tight, you may need to scale it a bit.
screw: 4x 40mm m3
thingiverse
free
Surgery Mask Support Frame by snackeater22
...e of surgery mask and this one is suitable for the largest one in hand. with a smaller mask, you can easily cut it with scissors.
V2
3d_export
free
Lamp v2
...lamp v2
3dexport
lamp v2 with solar panel
3d_export
$5
hammerhead v2
...hammerhead v2
3dexport
razer hammerhead v2 headphones, modeled in cinema 4d, render in corona
3d_export
$5
manometer v2
...manometer v2
3dexport
3d_export
$5
potato v2
...potato v2
3dexport
turbosquid
$52
Lifebuoys v2
...squid
royalty free 3d model lifebuoys v2 for download as fbx on turbosquid: 3d models for games, architecture, videos. (1560870)
turbosquid
$2
Mask v2
...turbosquid
royalty free 3d model mask v2 for download as stl on turbosquid: 3d models for games, architecture, videos. (1527741)
turbosquid
free
Flashlight V2
...d
free 3d model flashlight v2 for download as , obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1663559)
turbosquid
$29
Thanos v2
...
royalty free 3d model thanos v2 for download as ztl and obj on turbosquid: 3d models for games, architecture, videos. (1651077)
turbosquid
$29
Titan v2
...d
royalty free 3d model titan v2 for download as ztl and obj on turbosquid: 3d models for games, architecture, videos. (1540228)
turbosquid
$29
Frieza v2
...
royalty free 3d model frieza v2 for download as ztl and obj on turbosquid: 3d models for games, architecture, videos. (1701238)