Thingiverse
chike bag holder by sanktnelson
by Thingiverse
Last crawled date: 3 years, 1 month ago
I was annoyed by the limited cargospace of the chike cargobike when the children are in the seats, and the extra boxes to screw on the frame are ridicoulously expensive. So I made this bike-bag holder to use with the existing mountpoints for the boxes.
you need:
both sets of printed parts for left and right
6 M8 Bolts
M8 threaded rod ~10cm
10mm Aluminium Tube (<2m)
6 large M8 washers
2 M8 Nuts
Print from sturdy material (ABS or PETG, not PLA) with plenty of walls and high infill. I chose a relatively high tolerance for the holes, because I want to avoid smoothing holes by hand. If you don't or have a much more precise printer, reduce "tol".
The tube and bolts touch inside the parts, so hopefully most load is carried by direct metal-metal contact instead of just printed plastic.
Orienting the parts with the aluminum tube holes facing down (orientation=-90) probably results in stronger parts because the perimeters go around the tube, but may have too little suface area on the buildplate to stick properly. Set tube to false to get the tube sticking out incorporated in the hull, which increases the sticking surface and reduces overhangs. Or maybe you just like that variant better anyway.
you need:
both sets of printed parts for left and right
6 M8 Bolts
M8 threaded rod ~10cm
10mm Aluminium Tube (<2m)
6 large M8 washers
2 M8 Nuts
Print from sturdy material (ABS or PETG, not PLA) with plenty of walls and high infill. I chose a relatively high tolerance for the holes, because I want to avoid smoothing holes by hand. If you don't or have a much more precise printer, reduce "tol".
The tube and bolts touch inside the parts, so hopefully most load is carried by direct metal-metal contact instead of just printed plastic.
Orienting the parts with the aluminum tube holes facing down (orientation=-90) probably results in stronger parts because the perimeters go around the tube, but may have too little suface area on the buildplate to stick properly. Set tube to false to get the tube sticking out incorporated in the hull, which increases the sticking surface and reduces overhangs. Or maybe you just like that variant better anyway.
Similar models
thingiverse
free
Trashcan reduce bag holders by MD80
...
with these holders you can reduce the hole so that the bag fits into the trashcan.
the holders are glued onto the trashcan side.
thingiverse
free
Peugeot 306 2001 Cup Holder by matan290
... interior like i did i guess you could use hot glue or something like that because the hinge part is a very tight fit to the car.
thingiverse
free
Garbe bag holder / Müllsack Wandhalterung by salvador-richter
...ctures to the "i made" section.
09.08.2018
latest fix: corrected the drill in the bottom part, that it fits to the lid.
thingiverse
free
Spice holder by JannikSchulz
... holder" in petg and "spice holder mount" in pla.
i recommend https://www.thingiverse.com/thing:330151 as bag clip
thingiverse
free
Dry Box System
... doubtfull that it will work for you. included in the .rar file are solidworks files (.sldprt) for your modification and remixes.
thingiverse
free
Filament Storge by jmgijzel
...s and nuts. the hole is 1.75mm and i drilled it out to a 3 mm hole and added a ptfe tube in for smooth feeding thru the filament.
thingiverse
free
MendelMax Aluminum Plate Y-carriage Bed nut holder by MasterSketchup
...re stable bed platform during printing.
once printing, you have to mark and drill mounting holes to and bolt them to the plate.
thingiverse
free
Climbing Sticks, Tube Support with Handle & Drill Center
... hole right where you want it.
all holes are setup for grade 8, 5/16" hardware
if your interested in other sizes just pm me.
thingiverse
free
LED-strip holder for Anet A8 by SmallScaleFactory
...d a m8 threaded rod (approximately 40cm long) and a few washers and nuts. look at the pictures, you will see how it is assembled.
thingiverse
free
Tea Bag Holder by LeadMonk44
...supports. you don't have to follow the print settings that thingiverse gives you can just do what your printer is capable of.
Sanktnelson
thingiverse
free
spherecut by sanktnelson
...spherecut by sanktnelson
thingiverse
thing to test various infills and wall thicknesses for strength
thingiverse
free
Reelight holder by sanktnelson
..., but the hub version doesn't fit my mountainbike, and on the cabled version the holders are braindead, so i made an adapter.
thingiverse
free
bicycle bag holder reinforced by sanktnelson
...original holder was a bit flimsy and broke after half a year. but i liked the shape, so i made a significantly beefed up version.
thingiverse
free
wall-hook power drill bit by sanktnelson
...wer drill bit by sanktnelson
thingiverse
for screwing hooks and other things in and out where regular drill bits don't work.
thingiverse
free
KMX rear light mount on mudguard by sanktnelson
...nktnelson
thingiverse
name says it all. made for a b&m flatlight, but should fit many others (if not, use the source, luke!)
thingiverse
free
KMX trike phone holder by sanktnelson
...ince it is an adapter that allows me to stick the car holder for my htc legend onto the handlebars of my kmx trike (see picture).
thingiverse
free
Ultimate lash calibration piece by sanktnelson
...; to calibrate the backlash of your axis? here is the definite calibration piece: print once for each axis, no calipers required.
thingiverse
free
RV curtain glider by sanktnelson
...t. i was completely unable to find them in a store, so i bought a 3d printer and made them! wide part is 5mm, narrow part is 3mm.
thingiverse
free
Cupboard shelf pin by sanktnelson
...be paremeterizable, but i'm still getting the hang of openscad. you'll just have to scale it if you have the wrong holes.
thingiverse
free
rim dynamo conversion wheel for B&M dymotec by sanktnelson
...use this and a 27x3 o-ring to run your b&m dymotec on the rim instead of on the tire for less friction, losses and tire wear.
Bag
thingiverse
free
GRAB BAG (shopping bag) replacement clip
...ing bag) replacement clip
thingiverse
grab bag replacement clip
this is a replacement for the clip in the grab bag shopping bag.
thingiverse
free
Bag by Mulin
...bag by mulin
thingiverse
bag
thingiverse
free
Clip Bag
...clip bag
thingiverse
clip bag
thingiverse
free
bag clip
...bag clip
thingiverse
bag clip
thingiverse
free
Bag clip
...bag clip
thingiverse
bag closure
thingiverse
free
Bag Holder for plastic shopping bags by gtorelly
...bags by gtorelly
thingiverse
this is a bag holder designed to make it easier and more comfortable to carry lots of plastic bags.
thingiverse
free
pastry bag
...pastry bag
thingiverse
hi, this is 2 version for pastry bag for use in pastry.
thingiverse
free
Bag by Beatrice1975
...bag by beatrice1975
thingiverse
this is a project to build a bag with felt, plastic parts and magnets.
thingiverse
free
Simple Bag Clip
...simple easy to use household bag clips for sealing food bags.
fold over the bag and place the clip over the fold to seal the bag.
thingiverse
free
Dog Poop Bag with bag holder by dportero
...dog poop bag with bag holder by dportero
thingiverse
i wanted a bag holder that didn't need a carabiner.
Holder
thingiverse
free
Stubby holder holder
...der
thingiverse
bottom on the holder is sized for a can or bottle. top of the holder is sized for one in a cooler/stubby holder.
thingiverse
free
Soap holder holder
...soap holder holder
thingiverse
it's a holder to hold the famous soap holder.
thingiverse
free
bottle holder Jar holder can holder
...bottle holder jar holder can holder
thingiverse
hole diameter 38.6mm
thingiverse
free
Spool holder holder by vemotion
...spool holder holder by vemotion
thingiverse
pipe holder (16mm diameter)
thingiverse
free
smartphone holder with usb cable holder and key holder
...other of invention
this is my first creation basically smartphone holder with usb cable holder and key holder
i hope you like it
thingiverse
free
Holder of plate holders by budvar
...t; ;) holder for 5 pieces of modular plate holders from dave o https://www.prusaprinters.org/en/prints/15367-modular-plate-holder
thingiverse
free
Pen Holder/card holder by Pinky561
...pen holder/card holder by pinky561
thingiverse
a pen holder/card holder in one.
thingiverse
free
Toilet paper holder with phone holder
...toilet paper holder with phone holder
thingiverse
toilet paper holder with phone holder
thingiverse
free
Radio equipment holder and microphone holder
...radio equipment holder and microphone holder
thingiverse
radio equipment holder and microphone holder
thingiverse
free
Popsicle Holder Holder by billiamthesecond
...popsicle holder holder by billiamthesecond
thingiverse
keep popsicle holders upright so that they can be set down