Thingiverse
car rack by catfish3d
by Thingiverse
Last crawled date: 3 years ago
working 1/25 scale car rack
things you will need to complete this will be.
2x #10-24 nuts
2x #10-24 all thread rod approximately 5 1/2in in length each
1x piece of 3/32 piano rod/ wire to make the pins for the rack arm pivots
all of these extra materials can be found at hardware store and hobby/craft stores i.e. Lowes and hobby lobby
to assemble.
STEP 1 place a #10-24 nut into the receiving end of the nut holder and place nut and nut holder inside of the top part of the rack arm frame super glue may be required
STEP 2 assemble rack arms and rack pads again glue may be required
STEP 3 cut 4x pieces of 3/32 piano wire to length to make the pivot pins that will attach the front and rear rack arms to the rack arm frame
STEP 4 place rack arm frame assembly inside of the rack post and position towards the bottom of the post
STEP 5 cut a piece of #10-24 all thread to about 5in to 5 1/2 inches and place one end inside of the rack knob this should be a friction fit
STEP 6 glue rack top on top of the rack post super glue model glue or shoe goo could be used here
STEP 7 insert the all thread rod through the top of the rack and thread it into the nut placed inside of the rack arm frame until the knob is sitting on top of the rack
things you will need to complete this will be.
2x #10-24 nuts
2x #10-24 all thread rod approximately 5 1/2in in length each
1x piece of 3/32 piano rod/ wire to make the pins for the rack arm pivots
all of these extra materials can be found at hardware store and hobby/craft stores i.e. Lowes and hobby lobby
to assemble.
STEP 1 place a #10-24 nut into the receiving end of the nut holder and place nut and nut holder inside of the top part of the rack arm frame super glue may be required
STEP 2 assemble rack arms and rack pads again glue may be required
STEP 3 cut 4x pieces of 3/32 piano wire to length to make the pivot pins that will attach the front and rear rack arms to the rack arm frame
STEP 4 place rack arm frame assembly inside of the rack post and position towards the bottom of the post
STEP 5 cut a piece of #10-24 all thread to about 5in to 5 1/2 inches and place one end inside of the rack knob this should be a friction fit
STEP 6 glue rack top on top of the rack post super glue model glue or shoe goo could be used here
STEP 7 insert the all thread rod through the top of the rack and thread it into the nut placed inside of the rack arm frame until the knob is sitting on top of the rack
Similar models
thingiverse
free
T-handle organizer by marcvonamsberg
...s below the nut surface to ensure there are no sharp edges exposed. use the nuts in the bottom section to level your tool holder.
thingiverse
free
Z axis decoupler #10-32 rod by isotope32
...derneath the x axis. you are now ready to print your things, free from those annoying little wobbles caused by the threaded rods.
thingiverse
free
FLAK Rival Top Rail and Barrel by jdollars
...d rod and nuts to go through all the pieces, and a 30mm m3 bolt and nut to attach the rail from the main body to the rail set up.
thingiverse
free
Funky knobby knobs for fit on 8-32 or 4mm and 10-24 or 5mm threaded rod by ConceptualmaN
...readed rod . then let it cool in an upright position until the rod is cold . then you have a threaded rod with knob on the end !
thingiverse
free
Anet a8 rear-frame stabilizer\ cable holder by Adonay944
...ery tricky.
if you struggle fitting the spacers you can always preheat them in a cup of hot water then they should slide right in
thingiverse
free
1/4-20 Thumb Screw (1.5" Diameter)
...
you can then remove that nut and the bottom piece will not come out and it now prevents the internal nut from turning.
enjoy :)
thingiverse
free
Prusa i3 Printed, Reinforced Frame by s0nn46a13
...l structural integrity.
2 x 370 mm m8 threaded rod (sides)
1 x 225 mm m8 threaded rod (top)
1 x 220 mm m8 threaded rod (bottom)
thingiverse
free
Parametric Prusa i3 Frame Stabilizer kit by projunk
...(2x) (back)
m10 threaded rod 394 mm (2x) (y-axis)
m10 threaded rod 385 mm (2x) (sloping)
m10 nuts (46x)
m10 washers (46x)
thingiverse
free
-old- Mostly Printed CNC -Add On- Z Adjust Knob by Allted
... each other, locking them in place. slide the adjuster knob on to the top nut and its done.
print it as shown in the thingview.
thingiverse
free
Spool Holder for Printed Solid CR-10 Safety Enclosure, Anet A8 and more by electronron
...nuts should be used to prevent them from un-threading. make certain not to over tighten which will cause the bearings to bind up.
Catfish3D
thingiverse
free
tool box by catfish3d
...tool box by catfish3d
thingiverse
1/25 scale tool box with optional cabinets, hutch, top box, and semi functional drawers.
thingiverse
free
elegoo resin bottle holder by catfish3d
... your bottle drip when you've ran out.
this print for sure works on elegoo 500g bottles haven't tried a 1000g bottle yet
Rack
archibase_planet
free
Rack
...ack
archibase planet
rack paper rack rack for paper
rack 6 office n060914 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Rack
...ack
archibase planet
rack paper rack rack for paper
rack 3 office n060914 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Rack
...ack
archibase planet
rack paper rack rack for paper
rack 5 office n060914 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Rack
...ack
archibase planet
rack paper rack rack for paper
rack 7 office n060914 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Rack
...for magazines rack for notebooks notebooks notebook
rack notebook n120614 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Rack
...rack
archibase planet
rack umbrella umbrella rack
rack n180811 - 3d model (*.3ds) for interior 3d visualization.
archibase_planet
free
Rack
...rack
archibase planet
rack book rack stand
rack - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Rack
...rack
archibase planet
rack rack for glasses
rack 1 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Rack
...rack
archibase planet
rack rack for glasses
rack 2 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
free
rack
...rack
3dexport
rack
Car
3d_export
$5
car
...car
3dexport
luxury car high quality car
3d_export
$5
car
...car
3dexport
luxury car high quality car
3d_export
$5
car
...car
3dexport
luxury car high quality car
3d_export
$5
car
...car
3dexport
luxury car high quality car
3d_export
$5
car
...car
3dexport
luxury car high quality car
archibase_planet
free
Car
...
archibase planet
car sports car motor-car sportster
car nascar#1 n300114 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Car
...ibase planet
car motor-car sportster sports car
car gablota xform n190214 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Car
...car
archibase planet
car motor car transport
car vaz 2104- 3d model for interior 3d visualization.
3d_export
$15
car
...car
3dexport
car
3d_export
free
car
...car
3dexport
car