Thingiverse
Capacitive Soil Moisture Sensor by RonMcKay
by Thingiverse
Last crawled date: 4 years, 2 months ago
Capacitive Soil Moisture Sensor
This is a capacitive soil moisture sensor which runs with a standalone ATmega328P and utilizes the MySensors framework. It can however be adapted to any other framework that uses 2.4 GHz radio communication with a NRF24L01 if you upload your own code.
A short summary of the features is:
Runs on 2 AAA batteries
Uses a NRF24L01 radio module for communication
Utilizes an ATSHA204A for secure message signing
A sensor value range of approximately 400 (from air to water)
External 8MHz resonator for better temperature stability than the interal oscillator
3D printable case which should make the electronics waterproof if the seam to the pcb is sealed with silicone e.g.
Note: Take care when inserting the batteries as there is no reverse polarity protection on this board. Also check the pin assignment of the FTDI and AVR ISP headers as these might be non standard to save some space.
Getting Started
git clone --recurse-submodules https://github.com/RonMcKay/capacitive-soil-moisture-sensor
The PCB design is done in KiCad. You are pretty much good to go if you open the project with KiCad. The only thing that you need to add is the environment variable MYSLOCAL={root-path-to-the-hardware-folder}/lib
For programming and burning the bootloader I use Visual Studio Code together with PlatformIO and MiniCore (which is already included in the platform io plugin for vs code).
Future Improvements
Here is a list of possible future improvements that might be worth looking into:
Incorporating a voltage booster to increase battery runtime
Increase water proofing of the case by adding an o-ring at the bottom of the thread
Improve the thread model for easier printing and shorter screw on
Maybe improve the battery holder for increased stability
Add ready to use production files for JLCPCB, including SMT assembly files
Some temperature readings of the soil would be awesome, like an SMD thermistor or something similar at the tip of the sensor.
Any contributions are highly welcome and I am happy to discuss remarks in the github discussion section.
P.S.: The sensor on the photos is only a prototype where I accidentally soldered some wrong value capacitor and forgot a capacitor for the FTDI connector. These are however already fixed in the BOM and pcb design.
This is a capacitive soil moisture sensor which runs with a standalone ATmega328P and utilizes the MySensors framework. It can however be adapted to any other framework that uses 2.4 GHz radio communication with a NRF24L01 if you upload your own code.
A short summary of the features is:
Runs on 2 AAA batteries
Uses a NRF24L01 radio module for communication
Utilizes an ATSHA204A for secure message signing
A sensor value range of approximately 400 (from air to water)
External 8MHz resonator for better temperature stability than the interal oscillator
3D printable case which should make the electronics waterproof if the seam to the pcb is sealed with silicone e.g.
Note: Take care when inserting the batteries as there is no reverse polarity protection on this board. Also check the pin assignment of the FTDI and AVR ISP headers as these might be non standard to save some space.
Getting Started
git clone --recurse-submodules https://github.com/RonMcKay/capacitive-soil-moisture-sensor
The PCB design is done in KiCad. You are pretty much good to go if you open the project with KiCad. The only thing that you need to add is the environment variable MYSLOCAL={root-path-to-the-hardware-folder}/lib
For programming and burning the bootloader I use Visual Studio Code together with PlatformIO and MiniCore (which is already included in the platform io plugin for vs code).
Future Improvements
Here is a list of possible future improvements that might be worth looking into:
Incorporating a voltage booster to increase battery runtime
Increase water proofing of the case by adding an o-ring at the bottom of the thread
Improve the thread model for easier printing and shorter screw on
Maybe improve the battery holder for increased stability
Add ready to use production files for JLCPCB, including SMT assembly files
Some temperature readings of the soil would be awesome, like an SMD thermistor or something similar at the tip of the sensor.
Any contributions are highly welcome and I am happy to discuss remarks in the github discussion section.
P.S.: The sensor on the photos is only a prototype where I accidentally soldered some wrong value capacitor and forgot a capacitor for the FTDI connector. These are however already fixed in the BOM and pcb design.