Thingiverse
Bugs Bunny by reddadsteve
by Thingiverse
Last crawled date: 2 years, 11 months ago
Bugs Bunny, a fictional cartoon character in the Warner Bros. Looney Tunes/Merrie Melodies series.
Bugs is an anthropomorphic gray and white rabbit who is famous for his flippant, insouciant personality. Due to Bugs' popularity during the golden age of American animation, he became not only an American cultural icon and the official mascot of Warner Bros. Entertainment, but also one of the most recognizable characters in the world.
Bugs' trademark phrase is: "Eh...What's up, doc?"
This model is designed to be paired with my Elmer Fudd model to complete the full iconic scene with Bugs' finger in Elmer's gun (or scythe).
No supports are required. Two pieces contains built-in supports, optional parts without the built-in supports are also supplied if you want to use your slicer supports. If you have the proper filament colors, no painting is needed.
The assembled Bugs model is 134mm tall.
Enjoy!
...........................................................................................................
Print Instructions:
Supports: No
Resolution: .2mm
Infill: 10%
Notes:**
Refer to the notes below for a few helpful printing and assembly instructions.
...........................................................................................................
Building the model
Colors
Black: (Paramount3D PLA - Black)
whiskers_right
whiskers_left
eye_black_right
eye_black_left
hole_black
..
Light Pink: (eSun ABS - Pink)
ear_right
ear_left
nose
..
White: (Overture PLA - White)
eye_white_right
eye_white_left
hand_right
hand_left
body_white
body_white_nosupports (optional part without built-in supports)
..
Gray: (Paramount3D PLA -Prototype Gray)
body_gray
body_gray_nosupports (optional part without built-in supports)
body_gray_extra
..
Brown: (Gizmo Dorks ABS - Brown)
hole_brown
..
Natural: (eSun ABS - Natural)
teeth
..
...........................................................................................................
Printing and assembly tips
Printing tips
1 - No supports are required. The body_gray and body_white parts are presented with built-in supports as well as optional pieces without supports if you want to use your slicer supports.
2 - There are some pieces that may need brims or rafts, use your discretion. When setting up my prints I prefer to be conservative, especially since the base of many parts are hidden when inserted into another part. For the smaller parts, a good first layer is helpful.
*I used brims on:
hand_right
hand_left
nose
teeth
eye_black_right
eye_black_left
3 - Bugs' nose is sometimes shown as black, red or pink. I went with the light pink for my print.
4 - The model is meant to be displayed with Bugs' finger in Elmer's gun, however he can also be displayed standalone pointing to a sign. I'm hoping some makers will produce one or more appropriate signs and post them as remixes.
..
Assembly tips:
1 - Take your time gluing the model together and enjoy the process.
2 - I used E6000 sticky craft glue to put this model together. The sticky glue allows more time to position the parts than a fast drying superglue. I have 'fat fingers' and a shaky hand, so the sticky glue works out best for me, especially with small pieces. Just remember to leave enough time for the glue to set before combining too many parts.
3 - The hole_black has some rotational leeway when fitting into the hole_brown. I suggest gluing in the Bugs figure (body_gray/body_white/body_gray_extra/hand_right already glued together) into the hole at the same time as you glue the hole_black and brown together.
4 - The holes for the whiskers are symmetrical but for some reason on my printer I get a slight bridging hang on the hole for the left whiskers. If you have any problem fitting the whiskers in, just clean out any loose filament from the holes.
5 - Refer to the assembly diagrams in the pictures section as well as the uploaded pictures for putting the model together. The model is meant to be glued.
Do not hesitate to ask questions, feedback is essential to making better models.
Bugs is an anthropomorphic gray and white rabbit who is famous for his flippant, insouciant personality. Due to Bugs' popularity during the golden age of American animation, he became not only an American cultural icon and the official mascot of Warner Bros. Entertainment, but also one of the most recognizable characters in the world.
Bugs' trademark phrase is: "Eh...What's up, doc?"
This model is designed to be paired with my Elmer Fudd model to complete the full iconic scene with Bugs' finger in Elmer's gun (or scythe).
No supports are required. Two pieces contains built-in supports, optional parts without the built-in supports are also supplied if you want to use your slicer supports. If you have the proper filament colors, no painting is needed.
The assembled Bugs model is 134mm tall.
Enjoy!
...........................................................................................................
Print Instructions:
Supports: No
Resolution: .2mm
Infill: 10%
Notes:**
Refer to the notes below for a few helpful printing and assembly instructions.
...........................................................................................................
Building the model
Colors
Black: (Paramount3D PLA - Black)
whiskers_right
whiskers_left
eye_black_right
eye_black_left
hole_black
..
Light Pink: (eSun ABS - Pink)
ear_right
ear_left
nose
..
White: (Overture PLA - White)
eye_white_right
eye_white_left
hand_right
hand_left
body_white
body_white_nosupports (optional part without built-in supports)
..
Gray: (Paramount3D PLA -Prototype Gray)
body_gray
body_gray_nosupports (optional part without built-in supports)
body_gray_extra
..
Brown: (Gizmo Dorks ABS - Brown)
hole_brown
..
Natural: (eSun ABS - Natural)
teeth
..
...........................................................................................................
Printing and assembly tips
Printing tips
1 - No supports are required. The body_gray and body_white parts are presented with built-in supports as well as optional pieces without supports if you want to use your slicer supports.
2 - There are some pieces that may need brims or rafts, use your discretion. When setting up my prints I prefer to be conservative, especially since the base of many parts are hidden when inserted into another part. For the smaller parts, a good first layer is helpful.
*I used brims on:
hand_right
hand_left
nose
teeth
eye_black_right
eye_black_left
3 - Bugs' nose is sometimes shown as black, red or pink. I went with the light pink for my print.
4 - The model is meant to be displayed with Bugs' finger in Elmer's gun, however he can also be displayed standalone pointing to a sign. I'm hoping some makers will produce one or more appropriate signs and post them as remixes.
..
Assembly tips:
1 - Take your time gluing the model together and enjoy the process.
2 - I used E6000 sticky craft glue to put this model together. The sticky glue allows more time to position the parts than a fast drying superglue. I have 'fat fingers' and a shaky hand, so the sticky glue works out best for me, especially with small pieces. Just remember to leave enough time for the glue to set before combining too many parts.
3 - The hole_black has some rotational leeway when fitting into the hole_brown. I suggest gluing in the Bugs figure (body_gray/body_white/body_gray_extra/hand_right already glued together) into the hole at the same time as you glue the hole_black and brown together.
4 - The holes for the whiskers are symmetrical but for some reason on my printer I get a slight bridging hang on the hole for the left whiskers. If you have any problem fitting the whiskers in, just clean out any loose filament from the holes.
5 - Refer to the assembly diagrams in the pictures section as well as the uploaded pictures for putting the model together. The model is meant to be glued.
Do not hesitate to ask questions, feedback is essential to making better models.
Similar models
thingiverse
free
Elmer Fudd by reddadsteve
... model together. the model is meant to be glued.
do not hesitate to ask questions, feedback is essential to making better models.
thingiverse
free
Sylvester the Cat by reddadsteve
... model together. the model is meant to be glued.
do not hesitate to ask questions, feedback is essential to making better models.
thingiverse
free
Old Hag by reddadsteve
... model together. the model is meant to be glued.
do not hesitate to ask questions, feedback is essential to making better models.
thingiverse
free
Sign for Bugs/Elmer Scene by reddadsteve
... model together. the model is meant to be glued.
do not hesitate to ask questions, feedback is essential to making better models.
thingiverse
free
Rosie the Robot by reddadsteve
... model together. the model is meant to be glued.
do not hesitate to ask questions, feedback is essential to making better models.
thingiverse
free
Eeyore by reddadsteve
... model together. the model is meant to be glued.
do not hesitate to ask questions, feedback is essential to making better models.
thingiverse
free
Schroeder by reddadsteve
... model together. the model is meant to be glued.
do not hesitate to ask questions, feedback is essential to making better models.
thingiverse
free
Figment by reddadsteve
... model together. the model is meant to be glued.
do not hesitate to ask questions, feedback is essential to making better models.
thingiverse
free
Astro Jetson by reddadsteve
... model together. the model is meant to be glued.
do not hesitate to ask questions, feedback is essential to making better models.
thingiverse
free
Tweety Bird by reddadsteve
...- a number of the left/right parts look quite similar but are actually different. .. assembly tips: 1 -take...
Reddadsteve
thingiverse
free
Dilbert by reddadsteve
...required. if you have the right filament colors, no painting is needed.
the completed model is 225mm tall after assembly.
enjoy!
thingiverse
free
Dogbert by reddadsteve
...assembly. this model is in proportion to the dilbert, wally and pointy haired boss models that i've previously posted.
enjoy!
thingiverse
free
Hagar the Horrible by reddadsteve
...printing the pieces in the suggested colors. no supports are required.
hagar may look fierce but he is really a pussycat.
enjoy!
thingiverse
free
Rat by reddadsteve
...all after assembly. this model is in proportion to the pig and crocodile models from the comic that i've also posted.
enjoy!
thingiverse
free
Pig by reddadsteve
...tall after assembly. this model is in proportion to the pig and crocodile models from the comic that i've also posted.
enjoy!
thingiverse
free
Crocodile by reddadsteve
...tall after assembly. this model is in proportion to the pig and crocodile models from the comic that i've also posted.
enjoy!
thingiverse
free
Alice by reddadsteve
...n proportion to the dilbert, wally, pointy haired boss and dogbert models from the comic that i've previously posted.
enjoy!
thingiverse
free
Wally by reddadsteve
... is 200mm tall after assembly. this model is in proportion to the dilbert and pointy haired boss models previously posted.
enjoy!
thingiverse
free
Charlie Brown by reddadsteve
...ad luck.
no supports are required. if you have the proper filament colors, no painting is needed.
the model is 140mm tall.
enjoy!
thingiverse
free
Kermit the Frog by reddadsteve
...o supports are required. if you have the proper filament colors, no painting is needed.
the assembled model is 140mm tall.
enjoy!
Bunny
3d_export
$10
bunny
...bunny
3dexport
bunny, for 3d printing
3ddd
free
BUNNY
...bunny
3ddd
bunny
дизайн: boris berlin, aleksej iskos
1000х1000х1200h
3ddd
$1
Bunny chair
...bunny chair
3ddd
bunny , детское
creative bunny chair
turbosquid
$5
Bunny
...y
turbosquid
royalty free 3d model bunny for download as obj on turbosquid: 3d models for games, architecture, videos. (1374574)
3ddd
$1
Crazy Bunny
...crazy bunny
3ddd
кролик
crazy bunny
3d_export
$7
Easter bunny
...easter bunny
3dexport
easter bunny with easter egg on the grass
turbosquid
$25
Bunny
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$15
bunny
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
bunny
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
bunny with animations
...bunny with animations
3dexport
low poly bunny model with animation: run, fail, die, jump. maybe game assets
Bugs
turbosquid
$24
bugs / kyi bugs / insect
...royalty free 3d model bugs/kyi bugs/insect for download as ma on turbosquid: 3d models for games, architecture, videos. (1318597)
design_connected
$18
Bug
...bug
designconnected
poliform bug armchairs computer generated 3d model. designed by paola navone.
3ddd
$1
Poliform Bug
...poliform bug
3ddd
poliform , bug
кресло bug
производитель poliform s.p.a.
turbosquid
$3
Bug
...bug
turbosquid
royalty free 3d model bug for download as fbx on turbosquid: 3d models for games, architecture, videos. (1174243)
3ddd
$1
Poliform Bug
...poliform bug
3ddd
poliform , bug
enjoy!
turbosquid
$29
bugs
...lty free 3d model bugs for download as 3ds, obj, c4d, and fbx on turbosquid: 3d models for games, architecture, videos. (1443206)
turbosquid
$3
BUG
...alty free 3d model bug for download as max, 3ds, fbx, and stl on turbosquid: 3d models for games, architecture, videos. (1676677)
3d_ocean
$5
Beetle Bug
...beetle bug
3docean
beetle bug insect
a simple model of a beetle bug. - preview images rendered with mental ray -
turbosquid
$79
Bug
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$60
THE BUG
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.