GrabCAD
Birdo
by GrabCAD
Last crawled date: 2 years ago
It was a bit tough to design in such constraints but Adhesive based Valcro gave an extra advantage to keep the weight as low as possible. I used grabcad print service for any printing errors in the model and resolve the issues.
Model Structure Weight= 4.2g
Further details of the model is mentioned in a presentation along with method statement
1. Forces:
- Elecrtonics 42g = 0,41202N
- Motor thrust 120g = 1,1772N (per motor)
- Wires 25g = 0,24525N
- Battery 47g = 0,46107N
- Payload 250g = 2,4525N
- Motors 26g = 0,25506N
- Main Electronics = 0,20601N + 0,08175N = 0,28776N
- Elecrtonic Speed Controlers (4 pcs.) = 0,20601N + 0,08175N = 0,28776N
- Motors (4 pcs.) = 0,25506N + 0,08175N = 0,33681N
- Motor thrust = 1,1772N (per motor)
- Battery = 0,46107N
- Payload = 2,4525N
2. LC1 - Flying - area of the thrust - fixed (only the wieght of the components)
3. LC2 - Flying - surfaces of payload mounting - fixed - the wieght of components and the full thrust (it's more than just a payload)
4. LC3 - Standing - no payload (250g) and without thrust. On the surface of thrust i had to accept the minimum foce (0,01N), because when i put a zero (0N) simulation failed.
The frame after optimization is a compromise of weight to the possibility of printing.
You can go down with the weight but I'm not sure if it can be printed then or will not break while assembly of the other components.
Model Structure Weight= 4.2g
Further details of the model is mentioned in a presentation along with method statement
1. Forces:
- Elecrtonics 42g = 0,41202N
- Motor thrust 120g = 1,1772N (per motor)
- Wires 25g = 0,24525N
- Battery 47g = 0,46107N
- Payload 250g = 2,4525N
- Motors 26g = 0,25506N
- Main Electronics = 0,20601N + 0,08175N = 0,28776N
- Elecrtonic Speed Controlers (4 pcs.) = 0,20601N + 0,08175N = 0,28776N
- Motors (4 pcs.) = 0,25506N + 0,08175N = 0,33681N
- Motor thrust = 1,1772N (per motor)
- Battery = 0,46107N
- Payload = 2,4525N
2. LC1 - Flying - area of the thrust - fixed (only the wieght of the components)
3. LC2 - Flying - surfaces of payload mounting - fixed - the wieght of components and the full thrust (it's more than just a payload)
4. LC3 - Standing - no payload (250g) and without thrust. On the surface of thrust i had to accept the minimum foce (0,01N), because when i put a zero (0N) simulation failed.
The frame after optimization is a compromise of weight to the possibility of printing.
You can go down with the weight but I'm not sure if it can be printed then or will not break while assembly of the other components.
Similar models
grabcad
free
Generate Quadcopter Frame Ultra - 7,73g
...h shape optimizing and great fun!
thanks frustum!
generate link:
https://generate-de.frustum.com/#/workspace/1177/scenario/3345
grabcad
free
Generate Quadcopter Frame 40
...h shape optimizing and great fun!
thanks frustum!
generate link:
https://generate-de.frustum.com/#/workspace/1177/scenario/3324
grabcad
free
Ugly Bug Drone
...suface model of the frame, but this is only similar i have used for renderings. right shape frame is...
grabcad
free
Quadcopter Optimized Frame
... velcro.
- 4 escs: distributed on top of each arm.
generate link: https://generate-de.frustum.com/#/workspace/1217/scenario/3474
thingiverse
free
Thrust Tester by Printer239
...weight you get with the motor on and that is about how much it can carry. you can use tape to keep the motor and battery in place
thingiverse
free
Prusa Z motor mount and Coupling by Stu_Dkn
... giving some very nice prints.
the thrust bearing i found quite easily on ebay at â£7.00 for 4, and have an 8mm id and a 16mm od.
grabcad
free
Karawang Quadcopter
...karawang quadcopter
grabcad
this quadcopter can bring payload 250g. made in karawang.
grabcad
free
Quadruped drone
...its robustness.
volume: 11419 mm3
mass: about 12 g
generate url: https://generate-de.frustum.com/#/workspace/1126/scenario/3145
grabcad
free
Fly Quadcopter
...0 to max and balancing conditions for all cases will not be changed.
controllers motors as close to them
stl and stp files in zip
grabcad
free
Limit Generate Copter 7.95
...
(motors 4.4n =4.7n-0.3n (motors themselves, bolts, propellers
payload and battery divided over surface velcro and surface fixed)
Birdo
thingiverse
free
Birdo
...birdo
thingiverse
birdo.
you can support me on https://www.patreon.com/schlossbauer if you like my work.
thingiverse
free
birdo by PIGWIDGEON
...birdo by pigwidgeon
thingiverse
amazing birdo
thingiverse
free
Birdo stencil by Longquang
...birdo stencil by longquang
thingiverse
birdo stencil
thingiverse
free
Low Poly Birdo by West3DP
...n encountered in super mario bros 2 right before walking through a big bird mouth in a wall with a magic crystal. it's trippy
thingiverse
free
Birdo by deadlygeek
...to be glued in place. the bird rests on the stand without the need for any glue.
i would recommend printing the bird with a raft.
thingiverse
free
meh bird by alala2010
...meh bird by alala2010 thingiverse weirdo birdo ...
thingiverse
free
Super Mario Chess Set by West3DP
...- mushroom bad guys king - bowser queen - birdo bishop - bowser jr knight - koopa troopa rook...
3dwarehouse
free
New Birdo Island
...new birdo island
3dwarehouse
#mario_kart
3dwarehouse
free
Birdo Island WIP
...birdo island wip
3dwarehouse
my upcoming mario kart wii custom track #mario_kart