Big Flashlight Cone

...e for the small cree imitation flashlights i get off of wish.com. used to help me direct traffic during the haunted house season.

...ht cone by pyroz98 thingiverse this is a simple cone for the novled xml-t6 flashlight. i printed this with glow in the dark pla

... head of the light, stays in place. height: 15.3 cm diameter flashlight: 4.05 cm see caiofelipetzs make for a different approach.

...ashlight. use the customizer to change the top part to fit your flashlight. the stl uses a 35/38mm cone for the flashlight mount.

...torch maglite flashlight diffuser by sergiofpv thingiverse maglite mag charger cone traffic

...flashlight or volcano by lurgid thingiverse getting poor scans again. everything is just cones.

...e of magnets. those things cost about €20, so when he bought a new flashlight i knew it was time to 3d-print a replacement. :-)

...r results use translucent materials. but keep in mind even on lowest brightness highly transparent materials might be too bright.

... mais doit convenir pour toutes les lampes d'un diametre de 1 pouce ( 2,54 cm ) permet de diffuser le rayon lumineux à 360° .

... light to pass but glows for a decent amount of time when the light is turned off. x7r. this one is bulky by design :-) have fun!

...pla should be okay since the flashlight does not produce much heat). the flashlight used is a generic amazon thorfire flashlight.

...flashlight by tsuratt thingiverse flashlight created from a computer class

...flashlight by mojoman thingiverse flashlight with 5 parts and a removable disk for story telling.

...thingiverse flashlight holder dimensions 110 x 58 x 58 mm flashlight diameter 40 mm can be fix with double sided tape or screws.

...nerf flashlight by sergiomokshin thingiverse nerf flashlight diameter for body of my flashlight: 26.50mm

...light belt holder that was designed specifically for the nightstick flashlight (nsr-9844xl) but it may fit other flashlights too.

...flashlight by jtfagan thingiverse flashlight design. designed for a 6 volt battery, but had to be scaled down

...aller led flashlights. mounting hole is sized for a #8 self-tapping screw. can be easily resized to fit other size flashlights.

...hingiverse this is a flashlight frame for the prosthetic hand. it is compatible with a prosthetic hand attachment of spu design.

...flashlight clip by avidrine49 thingiverse flashlight belt clip to hold streamlight strion flashlight (smaller version)

...cone by muilenta thingiverse cone

...cone by 98linn thingiverse bullet cone for a rocket set

...paint cone thingiverse this is paint cone. one of paint accessory.

...speaker cone thingiverse custom design for a tweeter cone. wip

...cone thingiverse do it in 10% infil

...se just a traffic cone for all of your traffic cone needs. there is no need for much infill as it is hollow all the way through.

...xmas cone thingiverse fir cone decoration for your xmas tree.

...cone by baconron thingiverse it is a cone no need for infill due to the angle of printing

...traffic cone thingiverse traffic cone design with a small change to the top end.

...cone by ejaekle thingiverse http://mathvis.academic.wlu.edu/2015/07/20/quadratic-surfaces-cone/

...spring big thingiverse spring big

...big hook thingiverse big hook

...big bolter thingiverse big guns

...big bot thingiverse mechanical big bot

...big bolter h thingiverse big bolter

...big slug by adk08 thingiverse big slug

...big whistle by power911 thingiverse big whistle

...big sapin by 3dgoy thingiverse big sapin

...big gal by speedtwin69 thingiverse big gal

...the big piece by ludamega thingiverse the big piece