Bhatinov Mask for MN190 by rkayakr

... mfratto thingiverse this is a bhatinov mask for a celestron 8in sct. i designed the using the bahtinov mask drawings generator.

...raphy. edit the scad file for your specific lens, you can adjust the mask width for better visibility of the diffraction pattern.

...ngiverse meade lx200 10" sct bhatinov mask. i made this mask tight so it would stay in place if i needed to move the scope.

...auenza thingiverse bhatinov filter for celestron 8se. prints in two pieces and snaps together. print both pieces with supports.

...shayson mask to mask by tiger66639 thingiverse diving mask to mask

...hingiverse this is a remix of a bane mask and the montana mask. visit https://www.makethemasks.com/ for the montana mask files.

...matts mask by copperbuyer thingiverse basic mask for a surgical mask

...face mask holder by rawteq thingiverse face mask holder for 4 mask.

...mask by syzguru11 thingiverse mask

...mask by syzguru11 thingiverse mask

...h an example stl sized to cover the secondary holder of a skywatcher mn190 after installation of bob's knobs for collimation.

...lens to possible contamination and dew. this cap just covers the lens without touching it and without blocking the cooling holes.

...is an 80 mm fan mounted on a skywatcher mn190 if you resize for your own be careful. i...

...auenza thingiverse bhatinov filter for celestron 8se. prints in two pieces and snaps together. print both pieces with supports.

...raphy. edit the scad file for your specific lens, you can adjust the mask width for better visibility of the diffraction pattern.

... mfratto thingiverse this is a bhatinov mask for a celestron 8in sct. i designed the using the bahtinov mask drawings generator.

...bahtinov mask by scott_b thingiverse meade lx200 10" sct bhatinov mask. i made this mask tight so it would...

...h an example stl sized to cover the secondary holder of a skywatcher mn190 after installation of bob's knobs for collimation.

...e a stand for mounting an elecraft kx3 on a shelf. the scad design can be adapted for a kx2 or any rectangular device. 73 kd8cgh

...usdx lp filter box by rkayakr thingiverse usdx lp filter box with latching lid to hold extra lp filters.

...crews to self tread. print 2 button extensions. there is also a band bosrd carry case athttps://www.thingiverse.com/thing:4587868

... and cover plate simply hook into the slots in the psu. the fans i used draw 0.04 amp and are a negligible extra load on the psu.

...190. if you resize for your own be careful. i found that the fan screen was slightly larger and had sharper corners than the fan.

...t doesn't touch the dec axis. i used superglue to attach the pieces and a bit of tape to make sure the shield stays in place.

...supports by eric_csuf thingiverse this is a variation of rkayakr#39;s thing:https://www.thingiverse.com/thing:4100713 his was primarily to support bnc-sma adapters so...

...shayson mask to mask by tiger66639 thingiverse diving mask to mask

...mask thingiverse mask creation.

...sk thingiverse we all where mask!!!!!! btw i set this under the sub-straight in slicer(cura) to cut in half to be an actual mask

...mask by syzguru11 thingiverse mask

...mask by syzguru11 thingiverse mask

...mask by syzguru11 thingiverse mask

...mask by astorck thingiverse mask

...mask by dzecko thingiverse mask

...mask by leonk thingiverse mask

...mask by milena_3dstar thingiverse mask.