Thingiverse
![Belt Sleeve by gregware](/previews/8557352.jpg)
Belt Sleeve by gregware
by Thingiverse
Last crawled date: 3 years, 1 month ago
Overview
Remade same as origin of remix with OpenSCAD so it is parametric.
Added an optional bridge to pass the belt back, this has the added value to make sure nothing will slip and the belt remaining stripe doesn't flip around.
How to use
Pass your belt in the sleeve, with the teeth inwards, then buckle around your attachment point
Slide the sleeve out of the way of the returning belt stripe
Press the two belts together teeth-to-teeth so that they interlock
Adjust the two belt stripes notches to desired belt tension
Slide the sleeve back on the two joined together belt strips
Et voilà, there should be no slippage
Pass the belt back in the buckle
Adjusting belt tension
If you need to adjust the belt one notch this way or that to tighten/untighten, just slide the sleeve back out, move belts one notch and slide back sleeve in place
Printing
The openscad file has dimensions that yield a just-tight-enough sleeve when printed on the Tronxy X5S, so a bit over 6mm width (6.5) and height of 2.7 (vs the 6 and 2.4 of the original model which was too tight).
You can adjust this depending on your print tolerances.
Remade same as origin of remix with OpenSCAD so it is parametric.
Added an optional bridge to pass the belt back, this has the added value to make sure nothing will slip and the belt remaining stripe doesn't flip around.
How to use
Pass your belt in the sleeve, with the teeth inwards, then buckle around your attachment point
Slide the sleeve out of the way of the returning belt stripe
Press the two belts together teeth-to-teeth so that they interlock
Adjust the two belt stripes notches to desired belt tension
Slide the sleeve back on the two joined together belt strips
Et voilà, there should be no slippage
Pass the belt back in the buckle
Adjusting belt tension
If you need to adjust the belt one notch this way or that to tighten/untighten, just slide the sleeve back out, move belts one notch and slide back sleeve in place
Printing
The openscad file has dimensions that yield a just-tight-enough sleeve when printed on the Tronxy X5S, so a bit over 6mm width (6.5) and height of 2.7 (vs the 6 and 2.4 of the original model which was too tight).
You can adjust this depending on your print tolerances.
Similar models
thingiverse
free
![Belt Tensioner, adjustable R3 by boksbox](/t/8922833.jpg)
Belt Tensioner, adjustable R3 by boksbox
... spring type belt tensioner into an adjustable and rigid form.
fits gt-2 belts. openscad files included for your customization.
thingiverse
free
![Adjustable Belt Tightener by cahorton](/t/9016887.jpg)
Adjustable Belt Tightener by cahorton
...ng (just that there are teeth). only the belt height, width, and doubled height should need to be adjusted for other belt sizes.
thingiverse
free
![GT2 Tensioner for MP Select Mini by Kent0712](/t/8664459.jpg)
GT2 Tensioner for MP Select Mini by Kent0712
...r anymore after the mod, so i just used the original tensioner clip to gives additional tension after securing the belt together.
thingiverse
free
![Elastic Buckle by Foden7](/t/5026143.jpg)
Elastic Buckle by Foden7
... is to keep the elastic together on the back of your head
i've printed lots and they hold up extremely well
1/4" elastic
thingiverse
free
![Adjustable GT2 Belt Tensioner by stratop80](/t/8891930.jpg)
Adjustable GT2 Belt Tensioner by stratop80
... opposite side, so it can fit in different positions in the printer housing.
edit: added gt2-10mm belt body version (provisional)
thingiverse
free
![100% Printable Adjustable Belt Tensioner by jwoods01](/t/8773049.jpg)
100% Printable Adjustable Belt Tensioner by jwoods01
...e print is super simple too, without a real tensioner you can see the quality due to the slack, but it still printed very usable.
thingiverse
free
![Akali Belt Buckle Remix](/t/4927145.jpg)
Akali Belt Buckle Remix
...lerances are about 0.03 mm, so you may need to sand the prongs on the back plate or modify the model to make things fit together.
thingiverse
free
![Gamora's Belt Buckles by Sni9er](/t/8947029.jpg)
Gamora's Belt Buckles by Sni9er
...decided to attach them to standard belt buckles or by another means
happy costuming !!
luke
www.facebook.com/jjindustriesuk
thingiverse
free
![FolgerTech 2020 i3 Y Axis Belt Holder and Tensioner by JWag](/t/8734585.jpg)
FolgerTech 2020 i3 Y Axis Belt Holder and Tensioner by JWag
...un out of adjustment.
then just tighten the belt to tension and re-adjust after making a few prints to ensure good belt tension.
thingiverse
free
![I3 Y axis belt tensioner by Keugon](/t/8571710.jpg)
I3 Y axis belt tensioner by Keugon
...giverse
i just modelt the belt tensioner so i can model a securens thing around it so the bolt that holds the belt wont fall out
Gregware
thingiverse
free
![Cabinet-Stopper by gregware](/t/8624275.jpg)
Cabinet-Stopper by gregware
...are
thingiverse
this is just a simple stopper used to repair a shoe cabinet
it screws in place of the original (broken) stopper.
thingiverse
free
![CouvercleLeParfaitPlein by gregware](/t/8042472.jpg)
CouvercleLeParfaitPlein by gregware
...re-a-l-aide-d-un-bocal-type-le-parfait using openscad that imports the stl.
to run your own, get the stl file from the above url.
thingiverse
free
![Ender3CoverSpacer by gregware](/t/8042481.jpg)
Ender3CoverSpacer by gregware
...s the screws are not exactly symmetrically placed.
rear screw support should rest on the lower transversal profile of the ender3.
thingiverse
free
![Prusa i3 30mm fan duct (for MK8) by Gregwar](/t/8721280.jpg)
Prusa i3 30mm fan duct (for MK8) by Gregwar
...imply remove the front screw screw from your mk8 and remove the nylon spacer, insert the fanduct instead and put the screw again.
thingiverse
free
![Shimano Cassette Spacer by gregware](/t/8257199.jpg)
Shimano Cassette Spacer by gregware
....
the two stls have been generated one for testing (smaller outer disk), one for production, by altering the spreadsheet values.
thingiverse
free
![Spidey: an open-source parametric robotics platform by Gregwar](/t/8986290.jpg)
Spidey: an open-source parametric robotics platform by Gregwar
...stures, radio-command it, make it autonomous etc.
the project official page can be found here:http://www.robotcampus.fr/spidey/
thingiverse
free
![Rotation LED Clock Enclosure by gregware](/t/8635867.jpg)
Rotation LED Clock Enclosure by gregware
...re like 67 mm, maybe both are 67 mm after all. see back view picture (printed at 66mm)
printed one for ec1515b with angled stand.
thingiverse
free
![Plater: plate generator and optimizer by Gregwar](/t/8989663.jpg)
Plater: plate generator and optimizer by Gregwar
...inaries (v1.0), qt 4.8 and opengl required
get osx dmg (v1.0), thanks to toby tomkins
sources and repository
plater on github
thingiverse
free
![Spindle Spool Hub holder SCAD by gregware](/t/8743164.jpg)
Spindle Spool Hub holder SCAD by gregware
...i'm using triangles.scad from http://www.thingiverse.com/thing:220868
and screw library http://www.thingiverse.com/thing:8793
Sleeve
turbosquid
$5
![Sleeve](/t/13518929.jpg)
Sleeve
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$1
![sleeve](/t/13328888.jpg)
sleeve
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
design_connected
$11
![Hurricane sleeve](/t/4569005.jpg)
Hurricane sleeve
...hurricane sleeve
designconnected
smallaccents hurricane sleeve computer generated 3d model.
turbosquid
$6
![Y165 Sleeve](/t/13443390.jpg)
Y165 Sleeve
...urbosquid
royalty free 3d model y165 sleeve for download as on turbosquid: 3d models for games, architecture, videos. (1615514)
turbosquid
$4
![Sleeve avto](/t/13518892.jpg)
Sleeve avto
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_ocean
$8
![Long Sleeve Shirt](/t/41050.jpg)
Long Sleeve Shirt
...ils of long sleeve shirt. you can customize very easy.[not convert to edit polly ] rendering format – vray materials ̵...
turbosquid
$40
![Sleeve puffed shirt](/t/13456536.jpg)
Sleeve puffed shirt
...royalty free 3d model sleeve puffed shirt for download as max on turbosquid: 3d models for games, architecture, videos. (1469574)
turbosquid
$40
![Shirt puff sleeves](/t/13456493.jpg)
Shirt puff sleeves
...
royalty free 3d model shirt puff sleeves for download as max on turbosquid: 3d models for games, architecture, videos. (1476976)
turbosquid
$40
![dolman sleeved shirt](/t/13456495.jpg)
dolman sleeved shirt
...oyalty free 3d model dolman sleeved shirt for download as max on turbosquid: 3d models for games, architecture, videos. (1476035)
turbosquid
$50
![Petal Sleeves Dress](/t/13456520.jpg)
Petal Sleeves Dress
...free 3d model petal sleeves dress for download as max and pac on turbosquid: 3d models for games, architecture, videos. (1471891)
Belt
turbosquid
$9
![Belt conveyor belt](/t/13523059.jpg)
Belt conveyor belt
...t conveyor belt for download as 3ds, ige, obj, stl, and sldas on turbosquid: 3d models for games, architecture, videos. (1226546)
3d_export
$6
![belt](/t/11417817.jpg)
belt
...d then comes off and fastens at the front of the seat. version: 2015 units: millimetres x-form: yes polys: 120 950 verts: 163 944
3d_export
$7
![belt grinder](/t/11716069.jpg)
belt grinder
...belt grinder
3dexport
belt grinder
3d_export
$5
![Belt conveyor](/t/12718826.jpg)
Belt conveyor
...belt conveyor
3dexport
belt conveyor
3ddd
$1
![column belt](/t/866188.jpg)
column belt
...column belt
3ddd
колонна
column belt
turbosquid
$5
![Belt](/t/13397038.jpg)
Belt
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_ocean
$5
![Leather Belt](/t/40892.jpg)
Leather Belt
...ather belt is created in 3dsmax 2011 and rendered with vray 1.5 and it has all the texture included with the multiple obj format.
3d_ocean
$5
![Belt Ring](/t/862286.jpg)
Belt Ring
...belt ring
3docean
belt jewelry ring
belt ring 3d model. total weight 3.5 gram & 1.1 stone size. 3dm and obj file format.
design_connected
$11
![Belt Square](/t/4571354.jpg)
Belt Square
...belt square
designconnected
meridiani belt square computer generated 3d model. designed by parisio, andrea.
design_connected
$11
![Belt Round](/t/4571352.jpg)
Belt Round
...belt round
designconnected
meridiani belt round computer generated 3d model. designed by parisio, andrea.