Belt Buckle by rltaylor3

...tomorrowland belt buckle by mentalist thingiverse belt buckle

...y oddfellow thingiverse hellboy belt buckle. not tested as an actual belt buckle but it should fit your standard 1.5" belt.

...nal in nature; purely aesthetic. belt slides through buckle openings. fits a 45mm belt (approx. 2mm thick). modeled for cosplay.

...pin buckle belt hanger by pandro thingiverse belt hanger for belts with pin buckles.

...customizable belt buckle by kartellchef thingiverse a customizable belt buckle.

...coat belt buckle by leafleft thingiverse coat belt buckle

...buckle for grip6 type belts thingiverse belt buckle designed to be used with the grip6 style belts.

...seat belt buckle by portalsg thingiverse the belt buckle is designed to lock the seat belt signal

...sra buckle of belt use by joheinous thingiverse sra belt buckle

...e for grip6 style belts thingiverse belt buckle for grip6 style belts. buckle is plain so can be remixed however you would like.

...finger splint by rltaylor3 thingiverse a splint for a pinky finger

...pinky splint 2 by rltaylor3 thingiverse this is a pinky splint

...two links by rltaylor3 thingiverse made with 4 sides in section so it doesn't require rafting or supports.

...3 thingiverse this can serve as an alternative to a cast for the left pinky finger. i wore this for 3 weeks and it worked great!

...by rltaylor3 thingiverse this is a surface mounted door pull with 1/4" holes for screws. works very well with a 20% infill.

...too fussy. made from three lines in fusion that were piped and small fillet at the joint for little more strength and usability.

...finger splint 3.o by rltaylor3 thingiverse there are a few edges that need to be sanded down. otherwise it works pretty well.

...s, and an eraser. it was made to mount onto the frame or wall with either a screw, or even simple double sided tape. works great!

...tension buckle / ladder buckle thingiverse needed a replacement for a buckle that was broken. works well with 23x1.3mm straps.

...buckle by mkshft thingiverse buckle

...buckle by maria_3d thingiverse buckle

...buckle by bigfoot22 thingiverse buckle

...hl buckle thingiverse hl buckle

...buckle by delto thingiverse buckle for adjusting the lenght of a belt

...buckle by lotonp thingiverse jordan's buckle

...buckle by eduardochamorro thingiverse simple ring buckle for using with velcro

...scarf buckle by vd_max thingiverse scarf buckle / scarf ring / sarong buckle / pareo buckle etc.

...buckle by delto thingiverse the buckle i made is for adjusting a belt for a bag

...belt thingiverse belt sleeve for 35mm wide.. use tpu or tpu95 gcode ready

...belt hanger for mission belt by maburke thingiverse hanger for mission belt- hangs belt nicely on the closet rod

...belt hanger. this belt hanger works by placing the stud on the belt in the hole, then hang the hanger. yep, it's that simple.

...belt hanger for trakline belt by tomasf thingiverse a hanger for a single trakline belt.

...belt clip for 9 mm belt by papat400 thingiverse remix the belt lock gt2 for a 9mm belt

...belt rack thingiverse belt hanger

...belt holder thingiverse a simple belt holder.

...hermes belt buckle for 31mm belt by hubiro thingiverse hermes belt buckle for 31mm belt perfect to order as metal print :-)

...t buckle for 31mm belt by hubiro thingiverse bugati belt buckle made for 31mm hermes belt. perfect to order as a metal print :-)

...oner little different. after print you will need a: m3 nut m3 x10+ (screw length your choice) is for the gt2 belt with 6mm width