GrabCAD
![BbTransact Design Concept](/previews/1876838.jpg)
BbTransact Design Concept
by GrabCAD
Last crawled date: 2 years ago
Here's my first design for the Multi-Function Reader challenge by Blackboard Transact: https://grabcad.com/challenges/the-multi-function-reader-design-challenge
! CONCEPT !
-------------------
The main core unit by default includes the Display, Stand, Base, Side Modules (Mag Stripe reader and 'filler' Bin), and contactless/rfID reader as a front module.
DISPLAY:
This unit is ~7"w x 5"h with Screen that's 6"w x 4"h (~7" diagonal). It has an integrated Camera at the top, facing the customer. The Display unit attaches to the Stand with hinge allowing it to tilt up & down, with angle restriction possible.
STAND:
Attaches Display unit to the Base. Along with tilt motion, the Stand allows Display to swivel around 360 degrees by way of how it attaches to Base.
BASE:
This houses the Side Modules (card reader + bin or add-on options), Contactless credential reader (front module), RJ45 and USB ports, and Speaker. It can mount on a counter-top surface or on a wall. The ports area is designed so when unit's mounted on wall, cables will neatly exit horizontally rather than connectors sticking up... There could be small holes in back and front of base that allow cables to be fed through its interior from port area then out the front (which would be bottom in wall-mount situation). This way cables wouldn't interfere with slide-out modules.
SIDE MODULES:
In the primary BB Transact configuration, these would include the Mag Stripe card reader and a Bin that pens or small items can be put in. The bin is there as filler when no other extensions are added (like a computer's filler panel but more useful). When the person/company wants to add on extensions such as a receipt printer or braille keypad then the add-on can replace the bin in a side slot, or be standalone.
The idea is that these side modules/cartridges essentially use the same exterior molded shape rather than separate designs. Possibility: two-part design where all bottoms are same and tops snap on, since they can differ slightly whether for card swipe, receipt print, braille keypad, etc.
Each Side Module has a groove at the bottom where it can slide on and off a notch on the Base. If needed because of wall-mount option, it could also have a small clip- or snap-action incorporated so one has to pull harder or press the clip to release before sliding.
RFID READER (radio-frequency identification; contactless):
This would attach to the front of the Base with small clips for snap action and easy removal. It can be placed away from the core unit, set on counter-top for example, or on top of Mag Stripe reader.
ADD-ON OPTIONS/EXTENSIONS:
Aside from the extensions mentioned above for Side Modules, other add-ons can be integrated to the Display or Base units such as Micro SD card slot, Motion sensor, second Camera, Microphone, etc.
- I have the Micro SD slot placed at the underside of Display unit, where it's not blatantly visible but is easily accessed/used.
- I put the Motion Sensor on the top/back edge of the Base. It's positioned at an angle - so it can operate properly whether core unit is mounted on horizontal or vertical surface.
- If another Camera is added I imagine it being opposite the existing one at top of Display (not modeled).
Note: Two of my renderings use a pen 3D model that was created by Mark Hedron: https://grabcad.com/library/pen--3
My other concepts:
2nd: https://grabcad.com/library/bbtransact-design-concept-2-1
3rd: https://grabcad.com/library/bbtransact-design-concept-3-1
4th: https://grabcad.com/library/bbtransact-design-concept-4-1
! CONCEPT !
-------------------
The main core unit by default includes the Display, Stand, Base, Side Modules (Mag Stripe reader and 'filler' Bin), and contactless/rfID reader as a front module.
DISPLAY:
This unit is ~7"w x 5"h with Screen that's 6"w x 4"h (~7" diagonal). It has an integrated Camera at the top, facing the customer. The Display unit attaches to the Stand with hinge allowing it to tilt up & down, with angle restriction possible.
STAND:
Attaches Display unit to the Base. Along with tilt motion, the Stand allows Display to swivel around 360 degrees by way of how it attaches to Base.
BASE:
This houses the Side Modules (card reader + bin or add-on options), Contactless credential reader (front module), RJ45 and USB ports, and Speaker. It can mount on a counter-top surface or on a wall. The ports area is designed so when unit's mounted on wall, cables will neatly exit horizontally rather than connectors sticking up... There could be small holes in back and front of base that allow cables to be fed through its interior from port area then out the front (which would be bottom in wall-mount situation). This way cables wouldn't interfere with slide-out modules.
SIDE MODULES:
In the primary BB Transact configuration, these would include the Mag Stripe card reader and a Bin that pens or small items can be put in. The bin is there as filler when no other extensions are added (like a computer's filler panel but more useful). When the person/company wants to add on extensions such as a receipt printer or braille keypad then the add-on can replace the bin in a side slot, or be standalone.
The idea is that these side modules/cartridges essentially use the same exterior molded shape rather than separate designs. Possibility: two-part design where all bottoms are same and tops snap on, since they can differ slightly whether for card swipe, receipt print, braille keypad, etc.
Each Side Module has a groove at the bottom where it can slide on and off a notch on the Base. If needed because of wall-mount option, it could also have a small clip- or snap-action incorporated so one has to pull harder or press the clip to release before sliding.
RFID READER (radio-frequency identification; contactless):
This would attach to the front of the Base with small clips for snap action and easy removal. It can be placed away from the core unit, set on counter-top for example, or on top of Mag Stripe reader.
ADD-ON OPTIONS/EXTENSIONS:
Aside from the extensions mentioned above for Side Modules, other add-ons can be integrated to the Display or Base units such as Micro SD card slot, Motion sensor, second Camera, Microphone, etc.
- I have the Micro SD slot placed at the underside of Display unit, where it's not blatantly visible but is easily accessed/used.
- I put the Motion Sensor on the top/back edge of the Base. It's positioned at an angle - so it can operate properly whether core unit is mounted on horizontal or vertical surface.
- If another Camera is added I imagine it being opposite the existing one at top of Display (not modeled).
Note: Two of my renderings use a pen 3D model that was created by Mark Hedron: https://grabcad.com/library/pen--3
My other concepts:
2nd: https://grabcad.com/library/bbtransact-design-concept-2-1
3rd: https://grabcad.com/library/bbtransact-design-concept-3-1
4th: https://grabcad.com/library/bbtransact-design-concept-4-1
Similar models
grabcad
free
![BbTransact Design Concept 2](/t/1737307.jpg)
BbTransact Design Concept 2
...t-1
3rd: https://grabcad.com/library/bbtransact-design-concept-3-1
4th: https://grabcad.com/library/bbtransact-design-concept-4-1
grabcad
free
![BbTransact Design Concept 3](/t/1840609.jpg)
BbTransact Design Concept 3
...t-1
2nd: https://grabcad.com/library/bbtransact-design-concept-2-1
4th: https://grabcad.com/library/bbtransact-design-concept-4-1
grabcad
free
![BbTransact Design Concept 4](/t/1834594.jpg)
BbTransact Design Concept 4
...t-1
2nd: https://grabcad.com/library/bbtransact-design-concept-2-1
3rd: https://grabcad.com/library/bbtransact-design-concept-3-1
grabcad
free
![MFRD2](/t/1758269.jpg)
MFRD2
...sb ports
3. mic
4. mag stripe reader
5. network cable port
6. card slot
7. speakers
8. receipt printer
9. contactless card reader
grabcad
free
![BB Transact E2 by Tommy](/t/1785480.jpg)
BB Transact E2 by Tommy
...ransact-e4-by-tommy-1
https://grabcad.com/library/bb-transact-e1-by-tommy-1
https://grabcad.com/library/bb-transact-e3-by-tommy-1
grabcad
free
![Multi Reader Blackboard](/t/1795234.jpg)
Multi Reader Blackboard
...
msd resder
mag stripe reader
network jack - wired network connectivity (rj45)
contactless rfid cards
antenna
camera
headphone
grabcad
free
![BB Transact E1 by Tommy](/t/1716270.jpg)
BB Transact E1 by Tommy
...ransact-e4-by-tommy-1
https://grabcad.com/library/bb-transact-e2-by-tommy-1
https://grabcad.com/library/bb-transact-e3-by-tommy-1
grabcad
free
![Bb Door Reader V2](/t/2973328.jpg)
Bb Door Reader V2
... 130mm
-width: 85mm
-thickness: 28mm
note: 3d cad data and wall mount concept using bracket will be show later.
just for fun :)
grabcad
free
![Blackboard Door Reader](/t/1746915.jpg)
Blackboard Door Reader
...blackboard door reader
grabcad
braille, numeric, magnetic stripe card, contactless card
grabcad
free
![Multi - reader](/t/1830456.jpg)
Multi - reader
...ll , sd card location is at the bottom of the
screen
cabling is done from back of the screen
software : sw 2013
thanks,
vinya
Bbtransact
grabcad
free
![BbTransact Design Concept 4](/t/1834594.jpg)
BbTransact Design Concept 4
...t-1
2nd: https://grabcad.com/library/bbtransact-design-concept-2-1
3rd: https://grabcad.com/library/bbtransact-design-concept-3-1
grabcad
free
![BbTransact Design Concept 3](/t/1840609.jpg)
BbTransact Design Concept 3
...t-1
2nd: https://grabcad.com/library/bbtransact-design-concept-2-1
4th: https://grabcad.com/library/bbtransact-design-concept-4-1
grabcad
free
![BbTransact Design Concept 2](/t/1737307.jpg)
BbTransact Design Concept 2
...t-1
3rd: https://grabcad.com/library/bbtransact-design-concept-3-1
4th: https://grabcad.com/library/bbtransact-design-concept-4-1
Concept
grabcad
free
![Concept](/t/5493210.jpg)
Concept
...concept
grabcad
concept
grabcad
free
![concept](/t/8331916.jpg)
concept
...concept
grabcad
concept
grabcad
free
![concept](/t/1662900.jpg)
concept
...concept
grabcad
concept
grabcad
free
![concept](/t/5627883.jpg)
concept
...concept
grabcad
concept car
grabcad
free
![Concept](/t/5743401.jpg)
Concept
...concept
grabcad
my concepts
grabcad
free
![Concept](/t/8210801.jpg)
Concept
...concept
grabcad
main concept
grabcad
free
![Concept](/t/5466774.jpg)
Concept
...concept
grabcad
concept designed by me
grabcad
free
![Concept](/t/1655819.jpg)
Concept
...concept
grabcad
simple conception !
measurements are false .
grabcad
free
![Concept](/t/2926657.jpg)
Concept
...concept
grabcad
this is my first attempt of designing a concept vehicle.
grabcad
free
![CONCEPT](/t/5574278.jpg)
CONCEPT
...concept
grabcad
renders inspired by: https://grabcad.com/library/ford-gt-2016-concept-1
Design
grabcad
free
![Designer](/t/5354241.jpg)
Designer
...designer
grabcad
designer
grabcad
free
![Design](/t/2956666.jpg)
Design
...design
grabcad
designing
grabcad
free
![design](/t/1796587.jpg)
design
...design
grabcad
design
grabcad
free
![design](/t/1973967.jpg)
design
...design
grabcad
a design
grabcad
free
![design](/t/1666457.jpg)
design
...design
grabcad
design
grabcad
free
![design](/t/5756238.jpg)
design
...design
grabcad
design
grabcad
free
![Designer](/t/1653985.jpg)
Designer
...designer
grabcad
designer
grabcad
free
![design](/t/1680760.jpg)
design
...design
grabcad
design
grabcad
free
![design](/t/2921895.jpg)
design
...design
grabcad
design
grabcad
free
![Design](/t/7678830.jpg)
Design
...design
grabcad
design