Baffel Snoot by philfoleen

...9 thingiverse snoot for an inon z240 strobe. this requires a pair of m3x10mm hex head screws to secure the snoot to the strobe.

...astrimex akoestische baffels 3dwarehouse

...umatic npt brass muffler / baffel - 1 qtr in 3dwarehouse pneumatic npt brass muffler / baffel - 1 qtr in (drawn with sketchup 8)

...retra lsd snoot - replacement circular mask by cmontechi thingiverse replacement part of retra lsd optical snoot

...camera snoot for mini hitman by cardboard_boks thingiverse protective snoot for up to a 2.1mm lens on the nose of a mini hotman

...16mm contact printer snoot by ls3d thingiverse 16mm contact printing snoot for using on motorized sync blocks.

...ot for uw strobe: suitable for ikelite ds160 2x aluminum thumb screw for gopro https://www.apneasite.cz/diy-snoot-for-uw-strobe/

...snoot for inon z330 by acorchia thingiverse base on the diffuser i made a snoot for macro fusion 360 file included

...snoot for inon s-2000 thingiverse this is a snoot for inon s-2000 underwater flashlight build plate adhesion brim 4mm

...ng snoot for godox 250 di photography light unit by daveb500 thingiverse this snoot is designed for the godox 250 lighting unit.

... coaster by philfoleen thingiverse a coaster with the beer friends logo, for the discrening beer drinker's coffee table.....

...super surfer's s by philfoleen thingiverse a variation of the surfer's s you learned to draw in middle school

... stability instead of the two half circular nubs. this makes it a little stronger and a good bit more stable when under the can.

...;d really appreciate it. place two foam doughnuts inside the suppressor and super glue the end cap on to seal it, 14mm ccw thread

...bakak's design i've changed the openings and removed the baffel inside the air ducts to get an even better...

...of the ancient 4th century roman cup that has baffeld physists for years. it shows a different colour depending...

...design. however, i updated the design ( modern_pentagon_revised, modern_hexagon_revised, baffelrevised ) to attempt to correct these three problems. i...

...innerdiameter of the silencer and the length of the baffel. obviously those pieces cannot be used on...

...room for lipo battery added room for ldr added "baffelquot; for 40mm loudspeaker added housing for wemos with lipo...

...of the ancient 4th century roman cup that has baffeld physists for years. it shows a different colour depending...

...astrimex akoestische baffels 3dwarehouse

...umatic npt brass muffler / baffel - 1 qtr in 3dwarehouse pneumatic npt brass muffler / baffel - 1 qtr in (drawn with sketchup 8)

...9 thingiverse snoot for an inon z240 strobe. this requires a pair of m3x10mm hex head screws to secure the snoot to the strobe.

...snoot for inon z330 by acorchia thingiverse base on the diffuser i made a snoot for macro fusion 360 file included

...snoot for inon s-2000 thingiverse this is a snoot for inon s-2000 underwater flashlight build plate adhesion brim 4mm

...grid for snoot by marcoscrofani thingiverse direct the light on subject

...camera snoot for mini hitman by cardboard_boks thingiverse protective snoot for up to a 2.1mm lens on the nose of a mini hotman

...16mm contact printer snoot by ls3d thingiverse 16mm contact printing snoot for using on motorized sync blocks.

...ot for uw strobe: suitable for ikelite ds160 2x aluminum thumb screw for gopro https://www.apneasite.cz/diy-snoot-for-uw-strobe/

...retra lsd snoot - replacement circular mask by cmontechi thingiverse replacement part of retra lsd optical snoot

...he strobe to be postioned behind and to the side of the subject without light bleeding into the lens. inside dimensions are 96mm.