Thingiverse
Atmega8A-PU filament monitor with optical encoder for Marlin firmware by stinguc
by Thingiverse
Last crawled date: 3 years, 1 month ago
Atmega8A-PU filament monitor with optical encoder for Marlin 1.1.0-RC8 firmware
The second version can be found at https://www.thingiverse.com/thing:2838776
Having a cheap chinese hotend, from time to time i had filament filament grinding & clogging so naturally i searched for a filament monitor. None of them fulfilled my needs so i created one. Having some spare Atmega8A-PU microcontrollers and some phototransistors (http://www.tme.eu/en/details/ll-304ptc4b-1ad/phototransistors/lucky-light/) and using as inspiration 2 projects available on the internet:https://github.com/leuconoeSH/avr-exampleshttps://sites.google.com/site/tunelldev/home/filamentmonitor
i created a simple filament monitor which fullfilled my needs and is working without any issue for 1.5 months already.
The desing is simple and cheap to implement: 2 phototransistors, 2 leds, an atmega8 microcontroller and some 0.25w resistors & capacitors is all you need for electronics. Also 2 small pieces of ptfe tubes are nice to have, but not strictly required, in order to facilitate filament movement.
I used the PORTC of Atmega8A-PU microcontroller to sense and control the program logic.
PC5 is used for emitter led (the led which is used to detect the filament movement)
PC4 is used for the first phototransistor
PC3 is used for the second phototransistor
PC2 is used to display operation mode
PC1 is used to signal filament stoppage
PC0 is used to start the operations
The filament monitor uses, to monitor the filament movement, an optical encoder created by EMITTER_LED, A_RECEIVER, B_RECEIVER & wheell_alt.
After power on the default timeout to signal filament stoppage is set to 8 seconds.
There are 2 modes of operation:
1) If you short press the start button the default timeout (or the last timeout set) is used to detect filament stoppage
2) If you long press (at least 2 seconds) the start button, the filament monitor enters an mode where you can change the default timeout for filament stoppage detection. To set a new timeout you should keep the start button pressed until the desired timeout is set. The new timeout is indicated by OP_MODE_LED which blinks once at every second if the start button is pushed. So to set a timeout of 10 seconds proceed like that: press and hold the start button, wait 2 seconds (still holding the start button) and the OP_MODE_LED starts to blink, now count each blink and when 10 is reached release the start button. After each new timeout set the OP_MODE_LED displays the new timeout blinking for each second in the new timeout. So if you set 10 seconds as a new timeout, after start button release the OP_MODE_LED will blink for 10 times before start.
At any time, after start, you can stop the filament monitor by pressing the start button.
The OUT_PIN (pin 1 of PORTC) has a value of 0V on start and normal operation mode and will raise to 5V (for 2.5 seconds) on filament stoppage. Also on filament stoppage the OP_MODE_LED will blink.
After signalling a filament stoppage the monitor will stop so in order to restart it you will need to press the start button again. Also after a (re)start, without power off, the filament monitor will use the last timeout set.
To flash the microcontroller you can use the FilamentMonitor.hex file from filament_monitor.zip archive, also you can recompile the project from filament_monitor subfolder and use the recompiled hex file.
Fuses: LOW: 0xFF, HIGH: 0xC9
Any AVR programmer can be use to program the microcontroller. I used the one from Open Programmer (https://sourceforge.net/projects/openprogrammer/)
The monitor was designed for Marlin firmware & RAMPS 1.4 board but should be easilly adaptable to other configurations.
To connect the monitor to RAMPS 1.4 , please check the corresponding image. The signal provided by filament monitor will be connected to D44 on AUX-2.
The needed modifications of Marlin 1.1.0-RC8 firmware are available in marlin.patch from filament_monitor.zip archive.
When the filament monitor signals the error condition an M600 command is added to the current queue and previous and current enqueued commands are sent to the connected PC (if any), so if you use a program like Printrun (http://www.pronterface.com/) you will see in console something like:
M600 triggered.
Previous command: G1 X164.957 Y136.368 E4.70389
Enqueued commands: M600
Also you should activate M600 command in Configuration_adv.h (marlin firmware), uncomment the line:
// #define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too)
and change FILAMENT_CHANGE_X_POS, FILAMENT_CHANGE_Y_POS, FILAMENT_CHANGE_UNLOAD_LENGTH & FILAMENT_CHANGE_EXTRUDE_LENGTH accordingly to your printer settings.
wheell_alt.stl should be made from a non-transparent filament. I made all pieces from green non-transparent PLA. For EMITTER_LED i used a bright green one and for OP_MODE_LED i used a red one.
Optional components are presor_wheel.stl & arm.stl
The second version can be found at https://www.thingiverse.com/thing:2838776
Having a cheap chinese hotend, from time to time i had filament filament grinding & clogging so naturally i searched for a filament monitor. None of them fulfilled my needs so i created one. Having some spare Atmega8A-PU microcontrollers and some phototransistors (http://www.tme.eu/en/details/ll-304ptc4b-1ad/phototransistors/lucky-light/) and using as inspiration 2 projects available on the internet:https://github.com/leuconoeSH/avr-exampleshttps://sites.google.com/site/tunelldev/home/filamentmonitor
i created a simple filament monitor which fullfilled my needs and is working without any issue for 1.5 months already.
The desing is simple and cheap to implement: 2 phototransistors, 2 leds, an atmega8 microcontroller and some 0.25w resistors & capacitors is all you need for electronics. Also 2 small pieces of ptfe tubes are nice to have, but not strictly required, in order to facilitate filament movement.
I used the PORTC of Atmega8A-PU microcontroller to sense and control the program logic.
PC5 is used for emitter led (the led which is used to detect the filament movement)
PC4 is used for the first phototransistor
PC3 is used for the second phototransistor
PC2 is used to display operation mode
PC1 is used to signal filament stoppage
PC0 is used to start the operations
The filament monitor uses, to monitor the filament movement, an optical encoder created by EMITTER_LED, A_RECEIVER, B_RECEIVER & wheell_alt.
After power on the default timeout to signal filament stoppage is set to 8 seconds.
There are 2 modes of operation:
1) If you short press the start button the default timeout (or the last timeout set) is used to detect filament stoppage
2) If you long press (at least 2 seconds) the start button, the filament monitor enters an mode where you can change the default timeout for filament stoppage detection. To set a new timeout you should keep the start button pressed until the desired timeout is set. The new timeout is indicated by OP_MODE_LED which blinks once at every second if the start button is pushed. So to set a timeout of 10 seconds proceed like that: press and hold the start button, wait 2 seconds (still holding the start button) and the OP_MODE_LED starts to blink, now count each blink and when 10 is reached release the start button. After each new timeout set the OP_MODE_LED displays the new timeout blinking for each second in the new timeout. So if you set 10 seconds as a new timeout, after start button release the OP_MODE_LED will blink for 10 times before start.
At any time, after start, you can stop the filament monitor by pressing the start button.
The OUT_PIN (pin 1 of PORTC) has a value of 0V on start and normal operation mode and will raise to 5V (for 2.5 seconds) on filament stoppage. Also on filament stoppage the OP_MODE_LED will blink.
After signalling a filament stoppage the monitor will stop so in order to restart it you will need to press the start button again. Also after a (re)start, without power off, the filament monitor will use the last timeout set.
To flash the microcontroller you can use the FilamentMonitor.hex file from filament_monitor.zip archive, also you can recompile the project from filament_monitor subfolder and use the recompiled hex file.
Fuses: LOW: 0xFF, HIGH: 0xC9
Any AVR programmer can be use to program the microcontroller. I used the one from Open Programmer (https://sourceforge.net/projects/openprogrammer/)
The monitor was designed for Marlin firmware & RAMPS 1.4 board but should be easilly adaptable to other configurations.
To connect the monitor to RAMPS 1.4 , please check the corresponding image. The signal provided by filament monitor will be connected to D44 on AUX-2.
The needed modifications of Marlin 1.1.0-RC8 firmware are available in marlin.patch from filament_monitor.zip archive.
When the filament monitor signals the error condition an M600 command is added to the current queue and previous and current enqueued commands are sent to the connected PC (if any), so if you use a program like Printrun (http://www.pronterface.com/) you will see in console something like:
M600 triggered.
Previous command: G1 X164.957 Y136.368 E4.70389
Enqueued commands: M600
Also you should activate M600 command in Configuration_adv.h (marlin firmware), uncomment the line:
// #define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too)
and change FILAMENT_CHANGE_X_POS, FILAMENT_CHANGE_Y_POS, FILAMENT_CHANGE_UNLOAD_LENGTH & FILAMENT_CHANGE_EXTRUDE_LENGTH accordingly to your printer settings.
wheell_alt.stl should be made from a non-transparent filament. I made all pieces from green non-transparent PLA. For EMITTER_LED i used a bright green one and for OP_MODE_LED i used a red one.
Optional components are presor_wheel.stl & arm.stl
Similar models
thingiverse
free
Atmega8A-PU filament monitor with optical encoder for Marlin firmware v2 by stinguc
...ired, their are just examples of how the filament case can be used.
also sensor_wheel should be adjusted to your particular case.
thingiverse
free
Manneken Peace - 22/03/2016 by esteevens
...just barely works. (jozef prusa has totaly rewritten the m600 command support in his firmware, so i need to take a look at it).
thingiverse
free
Cura Script for Filament Change M600 command by Coramvaar
...working change filament script for cura, with the m600 marlin command.
tested on monoprice select mini v2 / maylan m200 printer.
thingiverse
free
XT60 Caps by OsiViper
...using a pause command or filament change (varies from machine to machine).
tested prints with pla, nylon and both of them worked.
thingiverse
free
RepRap Touch TFT LCD (mini pronterface style) by MarcoAntonini
...picaso firmware send commands through the gcode protocol to reprap main board.
the communication is done by a second serial port.
thingiverse
free
Discrete 7 Segment LED Clock by KiwiGrinder
...set the minutes
press the mode button and the normal time mode is shown. (denoted by the colon separator flashing once a second).
thingiverse
free
Drunk Domo Beer Bottle Opener - Multi Color by lukki15
...in the firmware and add m600 before and after the teeth and before the saliva. if you want to print it in three different colors.
thingiverse
free
Panda magnet bicolor
... is a hole on the back to glue a 8mm*3mm magnet. i recommend to rub the magnet a little with sandpaper to ease the glue to stick.
thingiverse
free
ISSF 10m AirPistol Timer by Trierscheid
...ady for the next competition shot.
this is very useful for training purposes, it makes fun and it made a lot of fun, building it.
thingiverse
free
Paste extrusion with pressure regulation by LolloHirsch
...in firmware). to insert these gcode commands before and after each travel move i used a postprocessing python script with slic3r.
Stinguc
thingiverse
free
TAL2 Telescope - Polar Axis Handwheel by stinguc
...scope - polar axis handwheel by stinguc
thingiverse
russian tal-2/tal-2t telescope - handwheel of micrometer screw of polar axis
thingiverse
free
Commodore Amiga 500 PC Floppy Mount and Eject Button by stinguc
... replacement eject button for this specific floppy drive.
the mounting brackets should be compatible with other pc floppy drives.
thingiverse
free
D-SUB 25 Male/Female Connector Case by stinguc
...modified the d-sub 25 connector and i removed the last pin from each row in order to fit the original amiga d-sub 23 connector :)
thingiverse
free
Commodore Amiga 500 Power Connector by stinguc
...to around 20 mm length or you can use the pins from a din 5/6/7/8/9 connector.
the metal shield was cut to size from a tin can :)
thingiverse
free
Atari ST DIN14 floppy disk drive connector by stinguc
... need at least 3 donor din 5.
also, you may find easier to insert the pins if you will use an solder iron heated to 200 degree c.
thingiverse
free
Atmega8A-PU filament monitor with optical encoder for Marlin firmware v2 by stinguc
...ired, their are just examples of how the filament case can be used.
also sensor_wheel should be adjusted to your particular case.
thingiverse
free
FinePix S9500 lens cover by stinguc
...finepix s9500 lens cover by stinguc
thingiverse
lens cover for fujifilm finepix s9500.
printed in abs
thingiverse
free
Laptop 50mm fan case by stinguc
...laptop 50mm fan case by stinguc
thingiverse
case for a 50mm laptop fan
thingiverse
free
Laptop 54mm fan case by stinguc
...laptop 54mm fan case by stinguc
thingiverse
case for a 54mm laptop fan
thingiverse
free
LM8UU bearing case by stinguc
...lm8uu bearing case by stinguc
thingiverse
lm8uu bearing case & holder
Pu
3ddd
$1
Декоративные кожаные 3D панели
...тек. кожаные 3d панели экологичны, так как изготовлены из pu высокотехнологичного материала (полиуретан). он имеет высокую износоустойчивость, не растягивается...
3ddd
$1
Декоративные кожаные 3D панели
...тек. кожаные 3d панели экологичны, так как изготовлены из pu высокотехнологичного материала (полиуретан). он имеет высокую износоустойчивость, не растягивается...
3ddd
$1
Декоративные кожаные 3D панели
...тек. кожаные 3d панели экологичны, так как изготовлены из pu высокотехнологичного материала (полиуретан). он имеет высокую износоустойчивость, не растягивается...
3ddd
$1
Partition Wall
...partition wall 3ddd панель mdf partition wall in white pu ...
3ddd
$1
Декоративные кожаные 3D панели
...тек. кожаные 3d панели экологичны, так как изготовлены из pu высокотехнологичного материала (полиуретан). он имеет высокую износоустойчивость, не растягивается...
3ddd
$1
Декоративные кожаные 3D панели
...тек. кожаные 3d панели экологичны, так как изготовлены из pu высокотехнологичного материала (полиуретан). он имеет высокую износоустойчивость, не растягивается...
3ddd
$1
SWIVEL CHAIR SOHO SOFT TIN
...35kg/m³, frame: plywood, seat cover: bycast - polyurethan upholstery: pu foam, base: aluminiium descripción: 90x79x52 ref....
3ddd
$1
Ambient Lounge® Fiorenze Sofa
...of course price) only. this is impeccaby individually stitched pu bonded leather fabric for those that are a little...
3ddd
$1
Кресло и пуфик Kempton Beige Fabric and Espresso PU Accent
...фик kempton beige fabric and espresso pu accent
кресло и пуфик с кожаной и вельветовой обивкой придадут атмосферу уюта интерьеру.
3ddd
$1
Двери Barausse
...barausse 3ddd двери , barausse двери barausse 1610 burano pu 1610 burano vu материалы corona и vray так же...
Marlin
archive3d
free
Building 3D Model
...building 3d model archive3d building pavilion construction building 1 marlin studio n051012 - 3d model (*.gsm+*.3ds) for exterior 3d...
3ddd
$1
Faro Marlin bra
...
marlin black wall lamphttp://www.faro.es/en/productos/marlin-lampara-aplique-negro/
polyrate: 15491
в архиве fbx+obj
3ddd
$1
360-panoramas_011
...360-panoramas_011 3ddd marlin studios - panoramica land & sky cd...
3ddd
$1
360-panoramas_017
...360-panoramas_017 3ddd marlin studios - panoramica land & sky cd...
3ddd
free
Brass Marlin
... винтаж , марлин
статуэтка марлина из латуни. винтаж.
archive3d
free
Building 3D Model
...building 3d model archive3d building pavilion construction building 2 marlin studio n051012 - 3d model (*.gsm+*.3ds) for exterior 3d...
archive3d
free
Car 3D Model
...car 3d model archive3d car motor-car automobile car marlin studio sub cb n311212 - 3d model (*.gsm+*.3ds) for...
3ddd
$1
360-panoramas_014
...360-panoramas_014 3ddd marlin studios - panoramica land & sky cd...
3ddd
$1
360-panoramas_015
...360-panoramas_015 3ddd marlin studios - panoramica land & sky cd...
3ddd
$1
360-panoramas_012
...360-panoramas_012 3ddd marlin studios - panoramica land & sky cd...
Encoder
3ddd
free
Zippo
...ысокополигональная модель культовой зажигалки zippo. выполнена 1:1 по реальному образцу до винтика. бе
3ddd
free
SMANIA Chic DeLuxe
...оригинальной картинки. 2 файла, со слитым и не слитым стэком. юзайте!xml version='1.0' encoding='%soup-encoding%'
thingiverse
free
F1 style wheel by _stark17
...12mm push buttons 3mm aluminum plade (for button-plade) joystick encoder 3x m5x70 screws 12x push buttons 2x 3 pin...
thingiverse
free
Project case for oled display and Arduino Nano with 9V battery by olkal
...following components: arduino nano oled display 1.3 inch rotary encoder (15mm or 20mm hight) on/off slide switch 9v battery...
thingiverse
free
Super Mario Lamp with 32x16 RGB LED animations by astraios3d
...esp32 board: https://aliexpress.com/item/32801621054.html flip flop power switch module: https://aliexpress.com/item/33054170454.html encoder buttons: https://aliexpress.com/item/32863292306.html usb a female connector: https://www.amazon.de/gp/product/b07tvhrh5q power connector:...
thingiverse
free
Cadetroller for Pico 8 by BulkDogan
...arcade joystick. what you'll need is a generic usb encoder and buttons. also a sanwa style joystick is needed....
thingiverse
free
control box mks sgen l v2+mks ts35 by patxinet
...used:https://www.thingiverse.com/thing:4583827 and i have added the hole for the encoder measurement plan courtesy of makerbase team, in files section...
thingiverse
free
Portal Gun (No internals suports) by Cargnelutti
...the handle. without the internals any board or rotary encoder can be used. for this build you will need...
thingiverse
free
Knobs series by Charlysix
...charlysix thingiverse 09/10/2020 final version of knobs for dual encoder inner knob 3 mm shorter than the previous version...
thingiverse
free
Flight Sim Single Rotary Knob Switch with Pushbutton by dlinebar
...usb arcade encoder $9.48 (will support 5 of the switches)https://www.amazon.com/reyann-arcade-encoderjoystick-fighting/dp/b00uurowwk/ref=sr_1_2_sspa?dchild=1&keywords=usb+arcade+encoder&qid=1600645388&sr=8-2-spons&psc=1&spla=zw5jcnlwdgvkuxvhbglmawvypuezrta5u1ddoeznu0u5jmvuy3j5chrlzelkpuewotqymje4ufcwulvxmzzlmkixjmvuy3j5chrlzefkswq9qta0mzc1mzy3wdvurkhen1gxotumd2lkz2v0tmftzt1zcf9hdgymywn0aw9upwnsawnrumvkaxjly3qmzg9ob3rmb2ddbgljaz10cnvl add about 40 cents in plastic and the switch...
Firmware
3d_export
$5
LENNY BED by Felis
...removable. an additional decor of the headboard is a firmware that imitates the capitonne technique. the bed can be...
3d_export
$5
Pepe stool by Opinion Ciatti Italian
...design provides a special slope. additional decor - manual firmware<br>32 x 48 x h58...
thingiverse
free
JGAurora/JGMaker A6 Mainboard Replacement STL files by DaHai8
...3d printer to a more user friendly mainboard and firmware please see my youtube video on how these are...
thingiverse
free
Ender 3 Pro Y-axis Damper for press fit steppers by carkom
...black m3 40mm bolts from x-axis cover) change your firmware to invert y-axis or do what i did -...
thingiverse
free
Arduino mini CNC plotter2 by imaicom
...to hold the pen in place.https://www.thingiverse.com/thing:4637226 i recommend this firmware because the y axis is reversing the motor.https://github.com/imaicom/grbl-28byj-48/ this...
thingiverse
free
PrusaSlicer profile for Easythreed X1 + extensive explanation of each setting by JacekJagosz
...make extruder "smarter" using linear advance, but that needs firmware changes. instead this makes head stop less, so the...
thingiverse
free
Tevo Tornado Filament Runout Sensor and Guide by gearworks
...of the carriage in the z direction. for the firmware update, i followed michael's guide here: https://youtu.be/gwhpxaj_6xe my version...
thingiverse
free
Arduino mini CNC plotter by imaicom
...to hold the pen in place.https://www.thingiverse.com/thing:4637226 i recommend this firmware because the y axis is reversing the motor.https://github.com/imaicom/grbl-28byj-48/ https://denshiman.com/arduino_mini_cnc_plotter.htmlhttps://denshiman.com/cnc.html...
thingiverse
free
i3 Mega Pro X-Carriage MK4 Laser Adapter Plate by Tinyhead
...going to be a parameter to change in the firmware - which i'm not prepared to tinker with at...
thingiverse
free
Ender 3 Pro BLTouch Mount by puturai
...probe offset on the firmware! probe offset for the firmware ...
Optical
3d_export
$42
Vanguard III Satellite 3D Model
...satellite 3d model 3dexport project vanguard rocket navy satellite optical sensors weather relay transmitter space orbit vanguard iii satellite...
3d_ocean
$7
Glasses 3D model
...lity 3d model of glasses and bonus scenes with all textures and materials for maxwell render and keyshot. thank you for watching!
3ddd
$1
Atina
...and ergonomical sitting position now with a new spring optical fabric. also available in other fabrics and color combinations....
archive3d
free
Telescope 3D Model
...telescope 3d model archive3d telescope spyglass optical device telescope bresser messier r-80 80-900 n110912 - 3d...
archive3d
free
Telescope 3D Model
...telescope 3d model archive3d telescope spyglass optical device telescope skywatcher dobsonian n170213 - 3d model (*.gsm+*.3ds)...
archive3d
free
Microscope 3D Model
...microscope 3d model archive3d microscope optical microscope microscope n180314 - 3d model (*.gsm+*.3ds) for interior...
3ddd
$1
Barovier&Toso Optical
...barovier&toso optical
3ddd
barovier&toso
люстра barovier & toso optical
артикул: 158732
h-1550x650
3ddd
$1
Quoizel Lighting Uptown Madison Manor 22" Pendant
...and: quoizel lighting
glass color: white linen shade
matches the following design styles: traditional, transitional, wrought iron
3d_ocean
$21
Canon EF 24 70 f/2.8 L USM
...otographer professional realistic
highly detailed canon lens. made in blender 2.69 for cycles rendering. only 1 texture 1024×1024
3d_ocean
$5
Wires: metal and plastic (3 models)
...copper cuprum industrial industry lead material max metal model optical plastic polyethylene polypropylene ravel rod set solder tin wire...
Monitor
3d_export
$18
LCD Big Screen MAX 2011 3D Model
...lcd screen tv plasma office games liquid crystal display monitor flat 3d lcd big screen max 2011 3d model...
3d_export
$50
Conference Room 01 3D Model
...room computer desk chair light table photometric tv lcd monitor keyboard mouse furniture max mental ray conference room 01...
3d_export
$50
Office 8 3D Model
...room computer desk chair light table photometric tv lcd monitor keyboard mouse furniture max mental ray office 8 3d...
3d_ocean
$39
Apple iMac 2015 4k – 5k RETINA with Accessories
...imac keyboard mac magic keyboard magic mouse magic trackpad monitor mouse retina trackpad set includes: apple imac 2015 5k...
3d_ocean
$12
Desk accessories (pen, eraser, etc.)
...etc.) 3docean coins desk desktop eraser marker mechanic pen monitor pc pen pencil stuff table tools desk stuff created...
3d_ocean
$29
Element3D - iMac 2015 (Retina 5K 27-inch)
...imac ios keyboard mac macintosh macos macosx magic keyboard monitor mouse retina trackpad here i present you with my...
cg_studio
$18
Digital picture frame remote low poly3d model
...television dvd centre lcd console digital device usb computer monitor screen .obj .max .fbx .3ds - digital picture frame...
cg_studio
$15
News Studio 0043d model
...cgstudio tv news television studio video live broadcast tripod monitor stage camera game cnn set virtual furniture exhibition stand...
cg_studio
$25
News Room Studio 0163d model
...cgstudio tv news television studio video live broadcast tripod monitor stage camera game cnn set virtual furniture exhibition stand...
cg_studio
$15
Tv Chat Program 0193d model
...cgstudio tv news television studio video live broadcast tripod monitor stage camera game cnn set virtual furniture exhibition stand...
Filament
3d_export
$5
Buld 3D Model
...lightbulb lantern candle illumination streetlight electric light bulb incandescent filament lamp glow-lamp inc buld 3d model kiko 50448...
3ddd
$1
RIBBED GLASS FILAMENT SCONCE AGED STEEL
...к:
ribbed glass filament sconce aged steel
dimensions
8¾"l x 7¾"w x 7"h
в архиве файлы: 2013 max. fbx. 6 текстур
3ddd
$1
Restoration Hardware
...restoration hardware 3ddd restoration hardware моделилась с каталогаhttp://www.restorationhardware.com/catalog/product/product.jsp?productid=prod2111782&categoryid;=cat2250024 sputnik filament chandelier polished nickel...
3ddd
$1
Filament Cage
...filament cage
3ddd
лофт , filament cage
модель бра, делалась по фото!
3ddd
$1
METAL FILAMENT SCONCE
...conce
3ddd
restoration hardware , sconce
материал хром. размеры бра 216 мм*191 мм*171 мм
archive3d
free
Bulb 3D Model
...bulb 3d model archive3d bulb light bulb lightbulb filament lamp electric bulb bulb lamp standart n071015 - 3d...
3ddd
$1
Black&White set
...и металла. в бонус бра бра cone 20th c.factory filament артикул 44.009.mt.bl.t1b сталь латунь высота 16 см диаметр 21,5...
3ddd
$1
20TH C. FACTORY FILAMENT METAL SCONCE - POLISHED NICKEL
...toration hardware
restoration hardware
бра:
dimensions
8½"l x 7½"w x 6¾"h
в архиве:
2013 max
2010max
fbx
preview
3ddd
$1
20TH C. FACTORY FILAMENT RIBBED GLASS SCONCE - POLISHED NICKEL
...ration hardware
бра:
20th c. factory filament ribbed glass sconce - polished nickel
dimensions
8¾"l x 7¾"w x 7"h
3ddd
$1
Steampunk Pendant
...such. we've lamped it with a pair of edison-style filament bulbs for a softened light in the style of:...