Thingiverse
![Anycubic Kossel Top Belt Tensioner by Atziano](/previews/8559944.jpg)
Anycubic Kossel Top Belt Tensioner by Atziano
by Thingiverse
Last crawled date: 3 years, 1 month ago
This thing is an top mounted belt tensioner which allows you to adjust the tightness of the timing belts with screws.
It is possible to lift up the top belt wheel for about 7mm.
If you put the timing belt already a bit taut during assembly, you will never need the full 7mm.
In my case, I only needed about 2mm.
In addition, these also serve as covers for the upper pulleys.
The belt tensioners is made out of two parts: the housing and the slider.
For all three belts of the Kossel, you need these two parts three times.
Also the belt have to be replaced because the position of the upper belt weel is about 15mm higher mounted. So the orginal belt is too short...unless you have left something extra length on the original timing belt.
For the assembly you need (for all three sides):
3 longer timing belts (about 40mm longer than the orginal one)
12 pieces of screws M4x8mm
12 pieces of T-nuts M4
9 pieces of screws M3x20mm
15 pieces of M3 nuts
There are two vesions of the covers to download:
V1.0 this version is without logos, signs and text.
V1.1 this version is with countersunk adjusting screws, direction arrows, +/- signs, deltalogo and min/max scale.
These two versions work exactly the same, the differences are only visual.
Please do not stretch the belt too much, a little more than with the original springs, that's enough.
To straighten all three belts the same way, i listen with my ear to the tensioners and peck at the belts like a guitar until the tone is equal.
It is possible to lift up the top belt wheel for about 7mm.
If you put the timing belt already a bit taut during assembly, you will never need the full 7mm.
In my case, I only needed about 2mm.
In addition, these also serve as covers for the upper pulleys.
The belt tensioners is made out of two parts: the housing and the slider.
For all three belts of the Kossel, you need these two parts three times.
Also the belt have to be replaced because the position of the upper belt weel is about 15mm higher mounted. So the orginal belt is too short...unless you have left something extra length on the original timing belt.
For the assembly you need (for all three sides):
3 longer timing belts (about 40mm longer than the orginal one)
12 pieces of screws M4x8mm
12 pieces of T-nuts M4
9 pieces of screws M3x20mm
15 pieces of M3 nuts
There are two vesions of the covers to download:
V1.0 this version is without logos, signs and text.
V1.1 this version is with countersunk adjusting screws, direction arrows, +/- signs, deltalogo and min/max scale.
These two versions work exactly the same, the differences are only visual.
Please do not stretch the belt too much, a little more than with the original springs, that's enough.
To straighten all three belts the same way, i listen with my ear to the tensioners and peck at the belts like a guitar until the tone is equal.
Similar models
thingiverse
free
![Idle Pulley Extension For Kossel Motors On The Top Configuration And Also a Belt Tensioner by spikelee](/t/8527266.jpg)
Idle Pulley Extension For Kossel Motors On The Top Configuration And Also a Belt Tensioner by spikelee
...ction of the two pieces
for durability , petg is highly recommended.
pla is ok for a short turn use, but it will crack over time.
thingiverse
free
![Hypercube easy Belt tensioner by bagwan](/t/8751692.jpg)
Hypercube easy Belt tensioner by bagwan
...screw-top side are to secure the screws after adjust the belts.
edit:
added a v2 with longer screw caps. so they can´t fall off.
thingiverse
free
![Timing belt adjustable tensioner by amedrano](/t/8874765.jpg)
Timing belt adjustable tensioner by amedrano
...t and a bolt (which ever you need, it is customizable too).
created as an alternative to http://www.thingiverse.com/thing:26361 .
thingiverse
free
![Adjustable Belt Tensioner by xifle](/t/9035157.jpg)
Adjustable Belt Tensioner by xifle
...her machines/belts too.
features:
adjustable
small, doesn't block mechanics
you only need a m4 set screw for assembly
thingiverse
free
![Improved Kossel Belt Tensioner by MegaMaking](/t/8687283.jpg)
Improved Kossel Belt Tensioner by MegaMaking
...m4x8 screws x12 (4 for each corner/tower)
m4 square nut x6 (2 for each corner/tower)
m4 tslot nuts x12 (4 for each corner/tower)
thingiverse
free
![Monoprice Select Mini X-Axis Belt Tensioner cap by justinschmitt](/t/8563346.jpg)
Monoprice Select Mini X-Axis Belt Tensioner cap by justinschmitt
...m length (longer will work too)
an m3 nut to insert into the knob (nyloc preferred)
a washer to go between the nut and end cap
thingiverse
free
![X belt tensioner for flyingbear P902 by cederron](/t/8765880.jpg)
X belt tensioner for flyingbear P902 by cederron
...he tension fast and easy.
installation takes 1 minute.
you will need 2 m4 screws and nuts, the nuts are press fit into the piece.
thingiverse
free
![Printrbot + y axis belt bracket tensioner by 69911e](/t/9053635.jpg)
Printrbot + y axis belt bracket tensioner by 69911e
...mproved y axis bracket belt tensioner with a screw adjustment.
uses original mount screw locations. you will need longer screws.
thingiverse
free
![Alfawise U10 belt tensioner Y by kobanaki](/t/8279058.jpg)
Alfawise U10 belt tensioner Y by kobanaki
...ll the orginal srews, belt and bearing, wen you want 1x a nut for the screw but not needed.
thx to the gusy that i remix it from!
thingiverse
free
![Tough Adjustable Belt tensioner](/t/4906152.jpg)
Tough Adjustable Belt tensioner
...lt tensioner
thingiverse
tightening belt without defotmation to itself. will hold the shape for long time.
need m3 nut and screw
Atziano
thingiverse
free
![Anycubic Kossel Linear Eckabdeckung by Nyemrinju](/t/8286420.jpg)
Anycubic Kossel Linear Eckabdeckung by Nyemrinju
...eckabdeckung by nyemrinju thingiverse angeregt durch die abdeckung von atziano sowie der "heated bed clips" (https://www.thingiverse.com/thing:2078581) von jameswhite habe...
thingiverse
free
![TPU Filament Mod Anycubic i3 Mega by Devtag](/t/8262369.jpg)
TPU Filament Mod Anycubic i3 Mega by Devtag
...meinen bedürfnissen angepasst die grundidee stammt von dem user "atzianoquot; ...
thingiverse
free
![Quiet Lightweight Magnetic Print Head - Kossel - e3D V6 by TBehr](/t/8257128.jpg)
Quiet Lightweight Magnetic Print Head - Kossel - e3D V6 by TBehr
...have made are to the print head itself. see atziano#39;s post for instructions on making the rods and carriages....
thingiverse
free
![Anycubic Kossel Plus Linear Magnet Upgrade Remix by slspeed](/t/8301715.jpg)
Anycubic Kossel Plus Linear Magnet Upgrade Remix by slspeed
...by slspeed thingiverse i remix the perfect design from atziano to use it with optical end switches and corner...
thingiverse
free
![Top Tensioner slider for Anycubic Kossel Linear Plus belts (in OpenSCAD)](/t/4790099.jpg)
Top Tensioner slider for Anycubic Kossel Linear Plus belts (in OpenSCAD)
...openscad) thingiverse background the top belt tensioner designed by atziano (see "remixed from" link on the left) is really...
thingiverse
free
![Belt tensioner / tightener for 2020 delta / Kossel 3D printer](/t/4647153.jpg)
Belt tensioner / tightener for 2020 delta / Kossel 3D printer
...ideal. i designed for 6mm gt2 belt, inspired by atziano belt tension can easily regulated by a knurled...
thingiverse
free
![Kossel K800 Magnetic Effector with inductive probe](/t/4984671.jpg)
Kossel K800 Magnetic Effector with inductive probe
...space between the arms of the great carriages from atziano in addition with an holder for a standard inductive...
thingiverse
free
![Anycubic Kossel Toolholder by Atziano](/t/8593429.jpg)
Anycubic Kossel Toolholder by Atziano
...ools and additionally for two files and a stainley hobby knife.
for mounting you need:
1 piece m4 t-nut
1 piece m4 screw 8mm long
thingiverse
free
![Anycubic Kossel Extruder TPU Upgrade by Atziano](/t/8594148.jpg)
Anycubic Kossel Extruder TPU Upgrade by Atziano
...de for printing flexible filament.
no slipping or ejection of flexible filaments.
update 23.09.2018: added a version without logo
thingiverse
free
![Anycubic Kossel Hotend Cableholder by Atziano](/t/8590526.jpg)
Anycubic Kossel Hotend Cableholder by Atziano
...r, this also means a strain relief for the cables from the hotend.
update 29.06.2020: added a new version with 45 degree angle...
Kossel
thingiverse
free
![Delta Corner Braces by 3dmpro](/t/8115870.jpg)
Delta Corner Braces by 3dmpro
...thingiverse inspired by the frame extension of the anycubic kossel linear, i developed an easy to print corner brace....
thingiverse
free
![Promega Z Roller Carriage by TheBum](/t/8149065.jpg)
Promega Z Roller Carriage by TheBum
...x 11mm x 6.35mm regular spacers three (3) mini kossel 5mm x 21.5mm x 7mm wheels m6 x 12mm...
thingiverse
free
![Kossel Mini FSR Bed Upgrade (MicroMake D1) by Lucidwolf](/t/8142459.jpg)
Kossel Mini FSR Bed Upgrade (MicroMake D1) by Lucidwolf
...dware savvy type. adding up cost of fsr sensors, time to solder, and nano the ~30 bucks plus shipping is a good deal for a kit.
thingiverse
free
![Kossel Frame Extenders by 3dmpro](/t/8138936.jpg)
Kossel Frame Extenders by 3dmpro
...board. in my case, i developed a simple rack that puts the board within range of all but one end-stop, which was simple to tweak.
thingiverse
free
![Anycubic Kossel Spool Rod by GeneKoh](/t/8143712.jpg)
Anycubic Kossel Spool Rod by GeneKoh
...bs against the tensioning knobs, so lengthened it another 25mm and this let me shift the spool towards the centre of the frame...
thingiverse
free
![FLSUN Kossel Delta Effector Sets by BeyondPrint](/t/8066943.jpg)
FLSUN Kossel Delta Effector Sets by BeyondPrint
...ad hotend
link here: https://rb.gy/inq8w9
3d filament 1.75mm color: red--->used in this print build<---https://rb.gy/0syrgd
thingiverse
free
![Kossel Z Axis Stabilizer & Bed Mount by DigitalSynergy](/t/8067056.jpg)
Kossel Z Axis Stabilizer & Bed Mount by DigitalSynergy
...finds this as useful as i did.
my print bed is 220mm round, but it should work for any size of kossel that uses 2020 extrusions.
thingiverse
free
![Anycubic Kossel ADXL345 Effector Mount by Qwuille](/t/8067243.jpg)
Anycubic Kossel ADXL345 Effector Mount by Qwuille
...ogo down, the cable holder can be printed however you deem right.
the cable canal is alittle small, but could not make it bigger.
thingiverse
free
![Better carriage with belt tensioner by PixelPicker](/t/8125942.jpg)
Better carriage with belt tensioner by PixelPicker
...better version of "carriage with belt tensioner for anycubic kossel plus" by alezsx. what i've done: as you can...
thingiverse
free
![Anycubic Kossel Linear Plus flex3drive flexible bowden remote motor Effector upgrade E3D V6 (Volcano too) and 5015 blower by rosch8](/t/8136747.jpg)
Anycubic Kossel Linear Plus flex3drive flexible bowden remote motor Effector upgrade E3D V6 (Volcano too) and 5015 blower by rosch8
...s still under the test
you need to set 2800 steps per mm for the first iteration and then make calibration of extruder for sure.
Anycubic
thingiverse
free
![Anycubic i3 mega direct Titan Aero by Kyneq](/t/8114167.jpg)
Anycubic i3 mega direct Titan Aero by Kyneq
...om the project https://www.thingiverse.com/thing:4361102
mount bltouch from the project https://www.thingiverse.com/thing:3065506
thingiverse
free
![Anycubic Chiron线缆改装 by WuM](/t/8114196.jpg)
Anycubic Chiron线缆改装 by WuM
...ic chiron原装线缆特别容易损坏且不美观,新的设计增大了线缆的回转角度,线缆也换成了专用的拖链线缆以避免损坏,拖在地上的线也变得整齐了。因为原装线缆比较短,该设计最麻烦的地方就是需要自己做线,一共有3种端子(phb、ph-t、xh)嫌麻烦可以直接焊接。
thingiverse
free
![Plotter attachment for Anycubic i3 Mega by ThomasKole](/t/8114376.jpg)
Plotter attachment for Anycubic i3 Mega by ThomasKole
...adapter onto the print head's left screw.
you can use inkscape to turn svg's into gcode, what's what i use.
have fun!
thingiverse
free
![Anycubic Mega Pro - Cable Holder by daedalas1981](/t/8114517.jpg)
Anycubic Mega Pro - Cable Holder by daedalas1981
... flush on the print head.
left side of the cable holder now flat for easier install and removal of the assisted bed level sensor.
thingiverse
free
![Anycubic Mega Zero Control Box extension for Heated Bed Mosfet and Octoprint Pi by rixxka2000](/t/8115289.jpg)
Anycubic Mega Zero Control Box extension for Heated Bed Mosfet and Octoprint Pi by rixxka2000
...cy is not spot on
you will need 4x m3 40mm screws to attach base through to original top cover.
any questions please ask
thanks
thingiverse
free
![Anycubic I3 Mega Filament Guide Bracked Remix by Desmoair](/t/8115707.jpg)
Anycubic I3 Mega Filament Guide Bracked Remix by Desmoair
...is a remix of the bracked from the remix of the ender 3 filament guide. the bracket was designed to mount on an anycubic i3 mega.
thingiverse
free
![Small Ball Mounting System (i.a. for CAMs like Pi, C270, GoPro) by wolwin_de](/t/8115735.jpg)
Small Ball Mounting System (i.a. for CAMs like Pi, C270, GoPro) by wolwin_de
...c270/c310 focus ringhttps://www.thingiverse.com/thing:3750229 object connections for the 3d printer anycubic i3m two clip holders were added for the left/right...
thingiverse
free
![Delta Corner Braces by 3dmpro](/t/8115870.jpg)
Delta Corner Braces by 3dmpro
...3dmpro thingiverse inspired by the frame extension of the anycubic kossel linear, i developed an easy to print corner...
thingiverse
free
![AI3M threaded spindle z-axis leading / Trapezspindelhalter by Schmelzerboy](/t/8148522.jpg)
AI3M threaded spindle z-axis leading / Trapezspindelhalter by Schmelzerboy
...z-axis leading / trapezspindelhalter by schmelzerboy thingiverse trapezspindelhalter für anycubic i3 mega mit rillenkugellager typ 608 2rs c3 this...
thingiverse
free
![A cutted version of max7th great Mark3 Design by DannyEss87](/t/8148813.jpg)
A cutted version of max7th great Mark3 Design by DannyEss87
...to print with a smaller 3d printer, like the anycubic i3 mega. the basic model is from...
Tensioner
3d_ocean
$4
![Photo Realistic Water/Paint Splash](/t/569933.jpg)
Photo Realistic Water/Paint Splash
...oplets at some spots. droplets are dominant in fluids like water because the surface tension in this fluids changes their shap...
3d_ocean
$12
![Transformer Station](/t/592013.jpg)
Transformer Station
...all applied materials: - textures formats: tif (x7), psd (x1) - textures sizes: x1024 (x1), x2048 (x6), x4096 (x1) - materials...
3ddd
$1
![Шезлонг KOII](/t/379365.jpg)
Шезлонг KOII
...the mat is built up with the two included tensioning ropes with beech balls at the end, and can be rolled together when not used.
3ddd
free
![Edwards Sofa](/t/786890.jpg)
Edwards Sofa
...m the tension between the exquisite workmanship of the deep-buttoned upholstery on the interior and the smooth external surfaces.
3ddd
$1
![Kenneth Cobonpue, yoda](/t/647687.jpg)
Kenneth Cobonpue, yoda
...ackrest gives yoda its unique character, a display that offers comfort disguised in randomness reminiscent of nature’s surprises.
cg_studio
$89
![BMW M6 Tension by Schnitzer Std mat3d model](/t/631886.jpg)
BMW M6 Tension by Schnitzer Std mat3d model
...x .lwo .max .obj - bmw m6 tension by schnitzer std mat 3d model, royalty free license available, instant download after purchase.
cg_studio
$89
![BMW M6 Tension by Schnitzer3d model](/t/681872.jpg)
BMW M6 Tension by Schnitzer3d model
...cgstudio
.3ds .max .obj - bmw m6 tension by schnitzer 3d model, royalty free license available, instant download after purchase.
cg_studio
$25
![Electric Fence v23d model](/t/924891.jpg)
Electric Fence v23d model
...n version
.obj .fbx .dae .c4d .3ds - electric fence v2 3d model, royalty free license available, instant download after purchase.
cg_studio
$25
![Electric Fence v13d model](/t/925054.jpg)
Electric Fence v13d model
...n version
.obj .fbx .dae .c4d .3ds - electric fence v1 3d model, royalty free license available, instant download after purchase.
cg_studio
$25
![Electric Fence v33d model](/t/925215.jpg)
Electric Fence v33d model
...n migrant
.obj .fbx .dae .c4d .3ds - electric fence v3 3d model, royalty free license available, instant download after purchase.
Belt
3ddd
$1
![column belt](/t/866188.jpg)
column belt
...column belt
3ddd
колонна
column belt
3d_ocean
$5
![Belt Ring](/t/862286.jpg)
Belt Ring
...belt ring
3docean
belt jewelry ring
belt ring 3d model. total weight 3.5 gram & 1.1 stone size. 3dm and obj file format.
3ddd
$1
![COIN chair](/t/1001282.jpg)
COIN chair
...material: base made of solid wood, seat made of belt and polyurethane foam upholstered with...
3ddd
$1
![Бодибилдинг_Set](/t/999195.jpg)
Бодибилдинг_Set
...от bodybuilding.com - гриф - пояс от cardillo weight belt (форма модели не задана - для придания формы используем...
3ddd
$1
![Gervasoni GHOST 10](/t/997268.jpg)
Gervasoni GHOST 10
...a sofa, multilayer and solid wood frame, with elastic belt, upholsterd with polyurethane foams, removable covers. three back cushions...
3d_ocean
$5
![Lifebelt 3D Object](/t/563099.jpg)
Lifebelt 3D Object
...ver, kisby ring or perry buoy. format included: lxo (for modo 401), obj, fbx the object has no uv map defined and no textures ...
3d_ocean
$5
![Spike Strip](/t/569103.jpg)
Spike Strip
...spike strip 3docean barricade belt block blow blowout city element flat out police road...
3d_ocean
$16
![Detailed Asteroids](/t/567477.jpg)
Detailed Asteroids
...sci-fi scenes… the extinction of the dinosaurs, the asteroid belt between earth and...
3d_ocean
$4
![Dollars](/t/568052.jpg)
Dollars
...dollars 3docean banknote bill crumpled dollar money dollar banknotes belt crumpled $100 bill, plane...
3d_ocean
$5
![Dagger 04](/t/566595.jpg)
Dagger 04
...design but lovely design, would fit perfekt in the belt of an assassin. between the handle and blade, i’ve...
Top
3d_export
$20
![Oven MAX 2011 3D Model](/t/283185.jpg)
Oven MAX 2011 3D Model
...hob stove cooker kitchen oven interior worktop cooking panel top pan oven max 2011 3d model motionmediaworkshop 69949...
3d_export
$29
![Bedside Table 3D Model](/t/296723.jpg)
Bedside Table 3D Model
...bedside table 3d model 3dexport side table drawers top wooden storage chest bedside table 3d model archicube.3d 74311...
3ddd
$1
![ferm_LIVING_baskets](/t/863828.jpg)
ferm_LIVING_baskets
...создаете себе красивый столик. в дополнение к столику идет декор.http://www.fermliving.com/webshop/shop/wire-baskets.aspx http://www.fermliving.com/webshop/shop/wire-baskets/wire-basket-top3.aspx http://www.fermliving.com/webshop/shop/all-products/winebottle-candleholder-5.aspx http://www.fermliving.com/webshop/shop/geometry-vase-1.aspx в архиве max...
3ddd
$1
![ISEN tables by Belta and Frajumar](/t/864356.jpg)
ISEN tables by Belta and Frajumar
...frajumar. dimensions: d80*h37 cm, d40*h45 cm. finishings: base: textile, top wood and stainless...
3ddd
$1
![Suar Wood Table Top Decoration](/t/866549.jpg)
Suar Wood Table Top Decoration
...suar wood table top decoration
3ddd
статуэтка , коряга
декор из дерева
3ddd
$1
![Mis en Demeure](/t/866564.jpg)
Mis en Demeure
...консоль в стиле прованс. франция. console avignon small marble top ...
3d_ocean
$85
![Mercedes 300SL Roaster Top](/t/861792.jpg)
Mercedes 300SL Roaster Top
...etailed interior. the model comes in five formats: -.blend, rendered with cycles, as seen in the images; -.obj, with materials...
3d_ocean
$4
![Earth](/t/861799.jpg)
Earth
...full game latest map most new planet plygon ready top world earth 3d model is available in all major...
3d_ocean
$99
![Full Land Rover Defender 90 Hard Top](/t/860264.jpg)
Full Land Rover Defender 90 Hard Top
...y detailed interior and chassis, with engine, gearbox, exhaust, suspension and brakes modeled. the model comes in five formats...
3d_ocean
$85
![Mercedes 300SL Roaster Top](/t/860335.jpg)
Mercedes 300SL Roaster Top
...etailed interior. the model comes in five formats: -.blend, rendered with cycles, as seen in the images; -.obj, with materials...