Thingiverse
Anycubic I3 Mega, Multicolor Upgrade, 3 colors by Dweezy
by Thingiverse
Last crawled date: 3 years ago
24.12.2019: Merry Xmas, Filaswitch is no longer needed, PrusaSlicer can do all the things needed.
25.12.2018: Merry Xmas, rumba-adapter-plate.stl (with external mosfet-place-holder) added.
DE:
Diese Erweiterung macht aus Eurem Any einen Anycubic I3 Mega³, dies ermöglicht 3-farbigen Druck, sowie Autobed-Leveling mit einem externem Display, was den Any sehr viel mehr bedienerfreundlich macht.
Das coole ist, Ihr könnte somit 1-farbig, 2-farbig oder 3-farbig drucken je nachdem was Ihr gerade als Vorlage habt.
!! Ich übernehme keinerlei Haftung oder Verantwortung dafür, denn dieser Umbau lässt Eure Garantie des Druckers erlischen. Jeder ist für die Modifizierung seines Druckers selbst verantwortlich !!
UND NEIN: Man kann das alte Trigorilla nicht nehmen, jedenfalls nicht das "alte 8bit" beim 32bit, hab ich garnicht nachgeschaut.
Schaut Euch die BOM an.
Bestellt die dort angegebene Teile.
Druckt Euch die Hotend-Aufnahme etc.
Baut den neuen Druckkopf mit Hotend auf einem Tisch zusammen.
Wenn Ihr alles zusammen habt und alles passt, baut den Drucker auseinander.
Baut Euer neues Hotend ein.
Baut Euer neues Mainboard ein.
Flashed die Firmware.
Habt Spass am Drucker.
Multicolor drucken heisst auch immer "Wasteblock" also "Filament-Verschwendung-Nennt-Es-Wie-Ihr-Wollt" seit Euch dessen bitte immer bewusst!
Da dieser Umbau den Einbau eines neuen Mainboards und das flashen einer Firmware erfordert, so solltet Ihr Euch mit folgenden Dingen "doch" gut auskennen:
Grundkenntnisse Elektrik
Grundkenntnisse Arduino
Marlin, wasn das?
Marlin auf den Arduino flashen
Der Kabelbaum sowie das mini PCB samt Schrauben im Extruderkopf des Anycubic werden direkt übernommen.
Zum Umbau:
Das "nervigste" an diesem Umbau ist eigentlich der Mainboard-Austausch. Ihr müsste dabei die Kabel vom originalem Trigorilla (ob nun 8bit alt oder 32bit) abziehen, umbedingt Beschriften! und dann auf das neue Mainboard bringen. Dazu gehen die Arduino Dupont Kabel sehr gut. Externes Display ans neue Mainboard stecken. Die neue Firmware ins Mainboard flashen.
Die X-Wellen lösen, ausführen, Hotend austauschen, den X-Riemen unter Spannung in den "x-belt-holder" einführen, dies erfordert etwas Konzentration. Danach die Stecker vom Bauteillüfter, Heizelement sowie Fühler auf das mini PCB stecken.
Wenn Ihr das geschafft habt, "Home'd" Ihr den Drucker im ausgeschaltetem Zustand von Hand (ja, ich weiss, das ist ein NOGO), und stellt schon einmal grob die Z-Achse ein. Der Aufbau vom neuen Hotend ist höher somit würdet Ihr sonst in die Ultrabase fahren.
Der Druck des 2-farbigen Frosches stellt eine echte Herausforderung an das Hotend, bzw. an das rein-und-raus vom Filament dar. Ich empfehle daher die Installation des externen Programms Filaswitch da man dort unterschiedliche Einzugsgeschwindigkeiten und Längen einstellen kann. Filaswitch bearbeitet den fertige gcode nachdem Ihr ihn in Cura oder Simplify erstellt habt. (Anycubic I3 Mega³.hwcfg-Datei in den Thing-Files ist die passende config für Filaswitch)
Wenn Ihr Filaswitch nutzen wollt, MÜSST ihr die beiden "s3d-*-section.txt" Dateien in Euer Simplify3D übernehmen, Filaswitch braucht die Angaben dort drinnen zum funktionieren!
Wenn Euch das zuviel wird, dann empfehle ich beim Farbwechsel/Toolchange einfach als "Einzugslänge / Rückzugslänge": 6.5cm und dann langsam mit einer Geschwindigkeit von 1200mm/min.
Rand-Notiz: Wenn Ihr Filaswitch benutzt erstellt gcode OHNE Waste-Tower, das übernimmt Filaswitch komplett!
Filament-Einführung: Das 1. Filament ganz normal und die 2 anderen jeweils bis zu dem Punkt mit dem Kugelschreiber (Bild 4) einführen.
An diesem Punkt, Gratulation, Viel Spass, Happy Printing :D
Bei fragen:
In der deutschen Anycubic Gruppe auf FB schreiben: Facebook, deutsche Anycubic I3 Mega Gruppe
Gefällt Dir der Mod? Über eine kleine Spende würden wir uns freuen :)
EN:
This extension turns your Any into an Anycubic I3 Mega³, allowing 3-color printing as well as auto-leveling with an external display, making the Any much more user-friendly.
The cool thing is, you could print in 1-color, 2-color or 3-color, depending on what you currently have as a template.
!! I assume no liability or responsibility for this, because this change will remove your warranty of the printer. Everyone is responsible for modifying their printer themselves !!
AND NO: You can not use the old Trigorilla, at least not the "old 8bit" the 32bit, I didnt looked.
Take a look at the BOM first!
Order the parts specified there.
Print the parts.
Build the new hotend on a table.
If you have everything together and everything fits, dismantle the printer.
Insert your new hotend.
Insert your new mainboard.
Flashed the firmware.
Have fun at the printer.
Multicolor printing also always means "Wasteblock", meaning "filament-waste-call-it-how-you-want", accept it!
Since this conversion requires the installation of a new motherboard and the flashing of a firmware, so you should be familiar with the following things:
The wiring-connector from the original extruder as well as the mini PCB together with screws in the extruder head of the Anycubic are used in this mod.
Assembly
The "annoying" part about this conversion is actually the mainboard change. You would have to remember/mark the cables from the original Trigorilla (whether 8bit or 32bit) and connect it on the new mainboard. Arduino Dupont Cable are doing very well. Plug the external display into the new motherboard. Flashing the new firmware into the motherboard.
Loosen the X-rods, move them apart, replace the hotend, insert the X-belt under tension into the "x-belt-holder", this requires some concentration. Then plug the connectors from the fan, heating element and thermal sensor onto the mini PCB.
After that, "home" the hotend by hand (mimimi, I know that's a NOGO), and adjust the Z-axis. The heigth of the new hotend is slightly higher as the old one. This means you would crash into your Ultrabase.
The 2-colored frog print was a real challenge for the hotend, or for the process of get filament in and out of the hotend. I therefore recommend the installation of the external program Filaswitch because you can set different speeds and length used for cooling inside the hotend. Filaswitch will process the finished gcode after creating it in Cura or Simplify. (Anycubic I3 Mega³.hwcfg file in the thing-files is the appropriate config for Filaswitch)
If you want to use Filaswitch, you MUST transfer the two "s3d - * - section.txt" files into your Simplify3D, Filaswitch needs the information inside to work!
If this is too much for you, then I simply recommend for the tool-change-process "retraction length": 6.5cm and slowly with a speed of 1200mm/min.
Notice: If you are using Filaswitch create gcode WITHOUT Waste-Tower, Filaswitch will do this !
Inserting filament: Insert the 1st filament as normal and the 2 others each to the point with the ballpoint pen (Figure 4).
At this point: congrats, have fun, happy printing :D
If there are any questions or complete builds:
Find me in the german oder english Anycubic I3 Mega group on FB
Like it? Feel free to tip :)
25.12.2018: Merry Xmas, rumba-adapter-plate.stl (with external mosfet-place-holder) added.
DE:
Diese Erweiterung macht aus Eurem Any einen Anycubic I3 Mega³, dies ermöglicht 3-farbigen Druck, sowie Autobed-Leveling mit einem externem Display, was den Any sehr viel mehr bedienerfreundlich macht.
Das coole ist, Ihr könnte somit 1-farbig, 2-farbig oder 3-farbig drucken je nachdem was Ihr gerade als Vorlage habt.
!! Ich übernehme keinerlei Haftung oder Verantwortung dafür, denn dieser Umbau lässt Eure Garantie des Druckers erlischen. Jeder ist für die Modifizierung seines Druckers selbst verantwortlich !!
UND NEIN: Man kann das alte Trigorilla nicht nehmen, jedenfalls nicht das "alte 8bit" beim 32bit, hab ich garnicht nachgeschaut.
Schaut Euch die BOM an.
Bestellt die dort angegebene Teile.
Druckt Euch die Hotend-Aufnahme etc.
Baut den neuen Druckkopf mit Hotend auf einem Tisch zusammen.
Wenn Ihr alles zusammen habt und alles passt, baut den Drucker auseinander.
Baut Euer neues Hotend ein.
Baut Euer neues Mainboard ein.
Flashed die Firmware.
Habt Spass am Drucker.
Multicolor drucken heisst auch immer "Wasteblock" also "Filament-Verschwendung-Nennt-Es-Wie-Ihr-Wollt" seit Euch dessen bitte immer bewusst!
Da dieser Umbau den Einbau eines neuen Mainboards und das flashen einer Firmware erfordert, so solltet Ihr Euch mit folgenden Dingen "doch" gut auskennen:
Grundkenntnisse Elektrik
Grundkenntnisse Arduino
Marlin, wasn das?
Marlin auf den Arduino flashen
Der Kabelbaum sowie das mini PCB samt Schrauben im Extruderkopf des Anycubic werden direkt übernommen.
Zum Umbau:
Das "nervigste" an diesem Umbau ist eigentlich der Mainboard-Austausch. Ihr müsste dabei die Kabel vom originalem Trigorilla (ob nun 8bit alt oder 32bit) abziehen, umbedingt Beschriften! und dann auf das neue Mainboard bringen. Dazu gehen die Arduino Dupont Kabel sehr gut. Externes Display ans neue Mainboard stecken. Die neue Firmware ins Mainboard flashen.
Die X-Wellen lösen, ausführen, Hotend austauschen, den X-Riemen unter Spannung in den "x-belt-holder" einführen, dies erfordert etwas Konzentration. Danach die Stecker vom Bauteillüfter, Heizelement sowie Fühler auf das mini PCB stecken.
Wenn Ihr das geschafft habt, "Home'd" Ihr den Drucker im ausgeschaltetem Zustand von Hand (ja, ich weiss, das ist ein NOGO), und stellt schon einmal grob die Z-Achse ein. Der Aufbau vom neuen Hotend ist höher somit würdet Ihr sonst in die Ultrabase fahren.
Der Druck des 2-farbigen Frosches stellt eine echte Herausforderung an das Hotend, bzw. an das rein-und-raus vom Filament dar. Ich empfehle daher die Installation des externen Programms Filaswitch da man dort unterschiedliche Einzugsgeschwindigkeiten und Längen einstellen kann. Filaswitch bearbeitet den fertige gcode nachdem Ihr ihn in Cura oder Simplify erstellt habt. (Anycubic I3 Mega³.hwcfg-Datei in den Thing-Files ist die passende config für Filaswitch)
Wenn Ihr Filaswitch nutzen wollt, MÜSST ihr die beiden "s3d-*-section.txt" Dateien in Euer Simplify3D übernehmen, Filaswitch braucht die Angaben dort drinnen zum funktionieren!
Wenn Euch das zuviel wird, dann empfehle ich beim Farbwechsel/Toolchange einfach als "Einzugslänge / Rückzugslänge": 6.5cm und dann langsam mit einer Geschwindigkeit von 1200mm/min.
Rand-Notiz: Wenn Ihr Filaswitch benutzt erstellt gcode OHNE Waste-Tower, das übernimmt Filaswitch komplett!
Filament-Einführung: Das 1. Filament ganz normal und die 2 anderen jeweils bis zu dem Punkt mit dem Kugelschreiber (Bild 4) einführen.
An diesem Punkt, Gratulation, Viel Spass, Happy Printing :D
Bei fragen:
In der deutschen Anycubic Gruppe auf FB schreiben: Facebook, deutsche Anycubic I3 Mega Gruppe
Gefällt Dir der Mod? Über eine kleine Spende würden wir uns freuen :)
EN:
This extension turns your Any into an Anycubic I3 Mega³, allowing 3-color printing as well as auto-leveling with an external display, making the Any much more user-friendly.
The cool thing is, you could print in 1-color, 2-color or 3-color, depending on what you currently have as a template.
!! I assume no liability or responsibility for this, because this change will remove your warranty of the printer. Everyone is responsible for modifying their printer themselves !!
AND NO: You can not use the old Trigorilla, at least not the "old 8bit" the 32bit, I didnt looked.
Take a look at the BOM first!
Order the parts specified there.
Print the parts.
Build the new hotend on a table.
If you have everything together and everything fits, dismantle the printer.
Insert your new hotend.
Insert your new mainboard.
Flashed the firmware.
Have fun at the printer.
Multicolor printing also always means "Wasteblock", meaning "filament-waste-call-it-how-you-want", accept it!
Since this conversion requires the installation of a new motherboard and the flashing of a firmware, so you should be familiar with the following things:
The wiring-connector from the original extruder as well as the mini PCB together with screws in the extruder head of the Anycubic are used in this mod.
Assembly
The "annoying" part about this conversion is actually the mainboard change. You would have to remember/mark the cables from the original Trigorilla (whether 8bit or 32bit) and connect it on the new mainboard. Arduino Dupont Cable are doing very well. Plug the external display into the new motherboard. Flashing the new firmware into the motherboard.
Loosen the X-rods, move them apart, replace the hotend, insert the X-belt under tension into the "x-belt-holder", this requires some concentration. Then plug the connectors from the fan, heating element and thermal sensor onto the mini PCB.
After that, "home" the hotend by hand (mimimi, I know that's a NOGO), and adjust the Z-axis. The heigth of the new hotend is slightly higher as the old one. This means you would crash into your Ultrabase.
The 2-colored frog print was a real challenge for the hotend, or for the process of get filament in and out of the hotend. I therefore recommend the installation of the external program Filaswitch because you can set different speeds and length used for cooling inside the hotend. Filaswitch will process the finished gcode after creating it in Cura or Simplify. (Anycubic I3 Mega³.hwcfg file in the thing-files is the appropriate config for Filaswitch)
If you want to use Filaswitch, you MUST transfer the two "s3d - * - section.txt" files into your Simplify3D, Filaswitch needs the information inside to work!
If this is too much for you, then I simply recommend for the tool-change-process "retraction length": 6.5cm and slowly with a speed of 1200mm/min.
Notice: If you are using Filaswitch create gcode WITHOUT Waste-Tower, Filaswitch will do this !
Inserting filament: Insert the 1st filament as normal and the 2 others each to the point with the ballpoint pen (Figure 4).
At this point: congrats, have fun, happy printing :D
If there are any questions or complete builds:
Find me in the german oder english Anycubic I3 Mega group on FB
Like it? Feel free to tip :)
Similar models
thingiverse
free
Anycubic I3 Mega, Diamond Hotend upgrade by Dweezy
...arriage.
- todo - i'm on it.
- todo - yes here too
- todo - ofc here also :)
flash the new firmware.
have fun at the printer.
3dwarehouse
free
Modernes Haus BETA 0.1
...as ihr auch gerne verwenden und verbessern dürft. wenn ihr einen vorschlag oder eine verbesserte version habt, dann schreibt mir.
thingiverse
free
TPU Filament Mod Anycubic i3 Mega by Devtag
...hmesser von 2mm.
ich habe das model lediglich meinen bedürfnissen angepasst die grundidee stammt von dem user "atziano"
thingiverse
free
Mosfet halter für Anycubic i3 Mega S by Macteckno
...ch den platz genutzt.
da wo das originale netzteil war ist nun der halter.
platz für
1x mosfet
1 x 50x50x10 lüfter
viel spaß :)
thingiverse
free
Anycubic I3 Mega Spool holder by Stipo_Tommy
... i3 mega. durch die anbringung wird das filament gerade eingezogen und verkantet nicht wie bei den meisten anderen spulenhaltern.
thingiverse
free
Messuhr Halter fuer Anycubic I3 Mega by Wastel
...ich habe noch eine 2te version erstellt für eine neue uhr mit befestigung an der rückseite.
uhrhalter2.stl und die fotos in grün.
thingiverse
free
LED-Holder Clip by itsybitsy
... und klemmen damit die led-streifen fest.
die clips können zur dauerhaften montage oder temporär als montagehilfe genutzt werden.
thingiverse
free
BUGA-Zwerg Karl by buga2019
...9.de/buga-zwerg
lasst mir doch ein like da oder postet bilder, wenn ihr mich gedruckt habt unter dem hashtag #bugazwerg
merci :-)
thingiverse
free
Aeons End Inlay - German Box by jan_lo
...lution: 0.3 mm
infill: nicht relevant
anmerkungen:
ihr benötigt alles einmal außer der cardbox_r_2x, diese benötigen sie zweimal.
3dwarehouse
free
Simples Haus
...nnt ihr es selbestverstaendlich auch veraendern. #dach #etage #fenster #haeuser #haus #schornstein #simple #simples #treppe #wand
Multicolor
turbosquid
$15
multicolored
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
multicolored columns
...multicolored columns
3dexport
multicolored columns, just columns, rainbow columns, crayons
3ddd
$1
Sylcom multicolor
...t;multicolor" на 8 рожков.p.s.: производитель может за дополнительную плату выполнить ее и в одном из предложенных цветов =)
turbosquid
$2
pillows multicolor
...ree 3d model pillows multicolor for download as blend and fbx on turbosquid: 3d models for games, architecture, videos. (1635489)
3ddd
$1
multicolor sofa
..., lounge , retail
sofa for a lounge area design
turbosquid
$13
Giftbox With Balloons multicolor
...el giftbox withbaloons multicolor for download as max and fbx on turbosquid: 3d models for games, architecture, videos. (1666410)
turbosquid
$15
Multicolored HANNELISE of IKEA
...ored hannelise of ikea for download as max, obj, 3ds, and fbx on turbosquid: 3d models for games, architecture, videos. (1691531)
turbosquid
$4
Multicolored futuristic ring
...uturistic ring for download as 3ds, obj, x, c4d, fbx, and dae on turbosquid: 3d models for games, architecture, videos. (1383689)
3ddd
$1
Axo Light / SP MUSE MULTICOLOR
...axo light / sp muse multicolor
3ddd
axo light
axo light sp muse multicolor
turbosquid
$15
Volkswagen Golf IV - Multicolor
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Anycubic
thingiverse
free
anycubic filament holder
...anycubic filament holder
thingiverse
anycubic filament holder
thingiverse
free
Cableholder Anycubic Mega
...cableholder anycubic mega
thingiverse
cableholder anycubic mega
thingiverse
free
AnyCubic Toolholder by WildManPrinting
...anycubic toolholder by wildmanprinting
thingiverse
anycubic i3 mega toolholder that clips on the side of the spool a-frame.
thingiverse
free
AnyCubic Funnel by phana007
...anycubic funnel by phana007
thingiverse
funnel for anycubic resin and also a reducer for a normal soda bottle.
thingiverse
free
Anycubic Kossel PID calibration
...ir mount:
kossel raspberry camera ir mount
extruder pid calibration.
simple extruder temperature calibration of your 3d printer.
thingiverse
free
anycubic mega i3
...anycubic mega i3
thingiverse
anycubic i3 mega/mega s led 30mm 10-14v 6500k
thingiverse
free
Handle for anycubic by cruiser7
...handle for anycubic by cruiser7
thingiverse
its easier to handle the cover of the anycubic mono x and wash&care
thingiverse
free
anycubic predator Printbed by Lihyon
...anycubic predator printbed by lihyon
thingiverse
anycubic predator printbed
thingiverse
free
Anycubic Predator Triggers by marcelcountry
...anycubic predator triggers by marcelcountry
thingiverse
anycubic predator triggers
thingiverse
free
support anycubic cable by sarpdental
...support anycubic cable by sarpdental
thingiverse
support anycubic cable
Mega
3ddd
$1
BoConcept / Mega
...boconcept / mega
3ddd
boconcept
boconcept mega
3ddd
free
Angelo - Mega shoin
... mega shoin , shoin
angelo - mega shoin - 3dmax 2008
3ddd
$1
Комод MEGA
...вана по фото с учетом реальных размеров.
стек не сколапсен, есть возможность регулировки уровня сглаживания.
текстуры в архиве.
3ddd
$1
Hulsta / Mega-design
...hulsta / mega-design
3ddd
hulsta
hulsta mega-design
design_connected
$18
Tolomeo Mega
...
photo-realistic 3d models of the tolomeo mega floor lamps from artemide for 3d architectural and interior design presentations.
turbosquid
$119
Mega Soldier
... free 3d model mega soldier for download as obj, c4d, and fbx on turbosquid: 3d models for games, architecture, videos. (1148568)
turbosquid
$100
Mega Yacht
... free 3d model mega yacht for download as obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1368903)
3ddd
$1
Massproductions Mega
... massproductions , mega
ширина: 180 см
глубина: 90 см
высота: 79 см
3d_export
$4
mega metro station
...mega metro station
3dexport
mega metro station. ready to game. thanks all downloaders!!
3ddd
$1
BAS Mega
...bas mega
3ddd
bas , ванна
ванна
Upgrade
turbosquid
$15
Upgraded Glock
...e 3d model upgraded glock for download as obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1185950)
3ddd
$1
Calligaris / UPGRADE
...calligaris / upgrade
3ddd
calligaris
c материалом
3d_export
free
cz upgrade
...cz upgrade
3dexport
https://www.buymeacoffee.com/mestrezen3d https://linktr.ee/mestrezen3
turbosquid
$80
Custer Tank upgrade
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$39
Domestos 1 upgrade
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$10
Upgraded tea cup
...upgraded tea cup
3dexport
a cup with an unusual design and a unique shape for a more enjoyable tea experience
3d_export
$8
dixy outlander classic style upgraded poplar wood lounge chair
...utlander classic style upgraded poplar wood lounge chair
3dexport
dixy outlander classic style upgraded poplar wood lounge chair
turbosquid
free
AK-12 + Upgrades low-poly 3D model
...ow-poly 3d model for download as fbx, blend, and unitypackage on turbosquid: 3d models for games, architecture, videos. (1501145)
evermotion
$700
Upgrade from V-ray 1.5 to 3.5 for 3ds max
...here is no need to purchase a new dongle - your current dongles will be reprogrammed to carry v-ray 3. evermotion 3d models shop.
evermotion
$300
Upgrade from V-Ray 2.0 to V-ray 3.5 for 3ds Max
... interface (gui) for editing settings on one machine and one render node for rendering on one machine. evermotion 3d models shop.
I3
3d_export
$10
suv i3
...suv i3
3dexport
suv i3 2013 series
3d_ocean
$89
BMW i3 2012
...y, in real units of measurement, qualitatively and maximally close to the original. model formats: - *.max (3ds max 2008 scanl...
cg_studio
$99
BMW i3 20143d model
...
cgstudio
.3ds .c4d .fbx .lwo .max .obj - bmw i3 2014 3d model, royalty free license available, instant download after purchase.
cg_studio
$99
BMW i3 20123d model
...tudio
.3ds .c4d .fbx .lwo .max .mb .obj - bmw i3 2012 3d model, royalty free license available, instant download after purchase.
cg_studio
$99
BMW i3 20143d model
...tudio
.3ds .c4d .fbx .lwo .max .mb .obj - bmw i3 2014 3d model, royalty free license available, instant download after purchase.
humster3d
$75
3D model of BMW i3 2014
...
buy a detailed 3d model of bmw i3 2014 in various file formats. all our 3d models were created maximally close to the original.
humster3d
$40
3D model of Kitchen Set I3
...uy a detailed 3d model of kitchen set i3 in various file formats. all our 3d models were created maximally close to the original.
3d_ocean
$30
Kitchen set i3
...ensils oven plates shelves sink table ware
kitchen set i3 include 3d models: cooker, oven, sink, cupboards, table, chair, plates.
3d_ocean
$89
BMW i3 2014
...y, in real units of measurement, qualitatively and maximally close to the original. model formats: - *.max (3ds max 2008 scanl...
cg_studio
$99
BMW i3 Concept 20113d model
...i3
.3ds .c4d .fbx .lwo .max .obj - bmw i3 concept 2011 3d model, royalty free license available, instant download after purchase.
Colors
design_connected
$11
Colors
...colors
designconnected
zanotta colors lounge chairs computer generated 3d model. designed by ilkka suppanen.
3ddd
$1
pillows colors
...pillows colors
3ddd
pillows colors , подушка
pillows colors
3ddd
free
color dress
...3ddd
color dress , манекен , одежда
color dress
3ddd
$1
светильники Colors
... massive , бельгия
светильники massive серия colors, очень веселые
3d_export
$30
color chameleon
...color chameleon
3dexport
color chameleon
3ddd
$1
color vase
...color vase
3ddd
color vase
3d_ocean
$2
color pen
...3d model of color pen. model is based on edge loop topology. all materials are included. model is render ready and ready for use.
3ddd
$1
Color Parquet
...color parquet
3ddd
паркет
color parquet
3ddd
free
color console
...color console
3ddd
консоль
color console
3d_export
$5
Technum Color
...technum color
3dexport
technum color led от imperiumloft https://imperiumloft.ru/dizajn-loft/technum-color-led.html
3
turbosquid
$10
Mountain Bike 3 -3 of 3
...model mountain bike 3 (#3 of 3) for download as fbx and blend on turbosquid: 3d models for games, architecture, videos. (1438752)
turbosquid
$6
Rock 3-3
...urbosquid
royalty free 3d model rock 3-3 for download as obj on turbosquid: 3d models for games, architecture, videos. (1628065)
turbosquid
$29
Books 150 pieces 3-3-3
...books 150 pieces 3-3-3 for download as max, obj, fbx, and stl on turbosquid: 3d models for games, architecture, videos. (1384033)
turbosquid
$3
Genesis 3 Clothing 3
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
hinge 3
...hinge 3
3dexport
hinge 3
3ddd
$1
Розетка 3
...розетка 3
3ddd
розетка
розетка 3
turbosquid
$50
is-3
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Mountain Bike 3 -2 of 3
...model mountain bike 3 (#2 of 3) for download as fbx and blend on turbosquid: 3d models for games, architecture, videos. (1438750)
turbosquid
$10
Mountain Bike 1 -3 of 3
...model mountain bike 1 (#3 of 3) for download as fbx and blend on turbosquid: 3d models for games, architecture, videos. (1438743)
3d_export
$5
3 CATS
...3 cats
3dexport
3 cats pen holder