Thingiverse
![Anet A8 SN04-N Auto Leveling Sensor Bracket by JMadison](/previews/8757293.jpg)
Anet A8 SN04-N Auto Leveling Sensor Bracket by JMadison
by Thingiverse
Last crawled date: 3 years, 1 month ago
This is a rework of http://www.thingiverse.com/thing:2019216 . This version adds additional cable management, a holder for the not-easily-accessible sensor nuts, and a design that uses the 8mm linear slider bearings to align the bracket. If you’re using a full cooling fan ring you’ll need to move to a half ring: http://www.thingiverse.com/thing:1954001
Sliced using Cura with the standard Anet A8 settings. The bracket used the normal profile, and the nut holder used high quality.
Standard Anet A8 Cura settings can be found in the comments section of the setup video: https://www.youtube.com/watch?v=gSXFHd-UDmE
The Marlin Configuration.h settings:
I determined these offsets using the grid file "Coords mm.pdf"
define X_PROBE_OFFSET_FROM_EXTRUDER -11 // X offset: -left +right [of the nozzle]
define Y_PROBE_OFFSET_FROM_EXTRUDER 31 // Y offset: -front +behind [the nozzle]
The Z_PROBE_OFFSET_FROM_EXTRUDER setting should be set based on your actual results during setup. See https://www.youtube.com/watch?v=tTl09r-E0wE . Note that the video uses Cura. I wasn’t able to get Cura to see the Anet board on my Mac so I used the Repetier-Host Mac.app.
define Z_PROBE_OFFSET_FROM_EXTRUDER -0.6 // Z offset: -below +above [the nozzle]
Update: See the comment from T3rorX. T3rorX has found the bed position settings I provide below to not be optimal. I'm no longer using this sensor so I'll let you decide which to use.
I was kind of iffy on these 4 settings:
define LEFT_PROBE_BED_POSITION 15
define RIGHT_PROBE_BED_POSITION 195
define BACK_PROBE_BED_POSITION 205
define FRONT_PROBE_BED_POSITION 25
Hardware: (2) M3 x 25, (2) M3 x 20. (It will work with longer versions of either, these are the exact sizes.)
Make sure you use thread locker such as https://www.amazon.com/gp/product/B000I1RSNS. I found that the sensor screws will loosen causing the sensor to drift closer to the bed if it's not secured tightly. When this happens it shows up as poor first layer adhesion.
I got the SN04-N sensor on eBay. There’s a huge range in price depending on whether you buy it with or without the connector. I got two for US $7.42 (from a US vendor) and added the connector myself. It came out cheaper than some of the assembled sensors, and you end up with a useful crimping tool for XH2.54 and JST 2.0 PH connectors.
Sensor: http://www.ebay.com/itm/351861131683
Connector: http://www.ebay.com/itm/252489099827
Crimping tool: https://www.amazon.com/gp/product/B00YGLKBSK
Sliced using Cura with the standard Anet A8 settings. The bracket used the normal profile, and the nut holder used high quality.
Standard Anet A8 Cura settings can be found in the comments section of the setup video: https://www.youtube.com/watch?v=gSXFHd-UDmE
The Marlin Configuration.h settings:
I determined these offsets using the grid file "Coords mm.pdf"
define X_PROBE_OFFSET_FROM_EXTRUDER -11 // X offset: -left +right [of the nozzle]
define Y_PROBE_OFFSET_FROM_EXTRUDER 31 // Y offset: -front +behind [the nozzle]
The Z_PROBE_OFFSET_FROM_EXTRUDER setting should be set based on your actual results during setup. See https://www.youtube.com/watch?v=tTl09r-E0wE . Note that the video uses Cura. I wasn’t able to get Cura to see the Anet board on my Mac so I used the Repetier-Host Mac.app.
define Z_PROBE_OFFSET_FROM_EXTRUDER -0.6 // Z offset: -below +above [the nozzle]
Update: See the comment from T3rorX. T3rorX has found the bed position settings I provide below to not be optimal. I'm no longer using this sensor so I'll let you decide which to use.
I was kind of iffy on these 4 settings:
define LEFT_PROBE_BED_POSITION 15
define RIGHT_PROBE_BED_POSITION 195
define BACK_PROBE_BED_POSITION 205
define FRONT_PROBE_BED_POSITION 25
Hardware: (2) M3 x 25, (2) M3 x 20. (It will work with longer versions of either, these are the exact sizes.)
Make sure you use thread locker such as https://www.amazon.com/gp/product/B000I1RSNS. I found that the sensor screws will loosen causing the sensor to drift closer to the bed if it's not secured tightly. When this happens it shows up as poor first layer adhesion.
I got the SN04-N sensor on eBay. There’s a huge range in price depending on whether you buy it with or without the connector. I got two for US $7.42 (from a US vendor) and added the connector myself. It came out cheaper than some of the assembled sensors, and you end up with a useful crimping tool for XH2.54 and JST 2.0 PH connectors.
Sensor: http://www.ebay.com/itm/351861131683
Connector: http://www.ebay.com/itm/252489099827
Crimping tool: https://www.amazon.com/gp/product/B00YGLKBSK
Similar models
thingiverse
free
![Sensor Mount for Anet A8 by mulger](/t/8282604.jpg)
Sensor Mount for Anet A8 by mulger
...0 // y offset: -front +behind [the nozzle]
//#define z_probe_offset_from_extruder 0 // z offset: -below +above [the nozzle]
thingiverse
free
![Anet A8 Sensor Bracket 12mm and 18mm by Leo_N](/t/8782191.jpg)
Anet A8 Sensor Bracket 12mm and 18mm by Leo_N
...not sensor related but the z homing speed was too fast for my taste. to have it move slower use:
define homing_feedrate_z (4*60)
thingiverse
free
![Anet A8 Front Fan Sensor Mount 18 mm by buzzkc](/t/8748280.jpg)
Anet A8 Front Fan Sensor Mount 18 mm by buzzkc
...://www.thingiverse.com/thing:2506274
the wiring schematic and parts list for my sensor: https://www.thingiverse.com/thing:2758533
thingiverse
free
![Anet A8 - Sensor Support by InLineTwinNemesis](/t/8287226.jpg)
Anet A8 - Sensor Support by InLineTwinNemesis
...ft_probe_bed_position 5
define right_probe_bed_position 195
define front_probe_bed_position 50
define back_probe_bed_position 205
thingiverse
free
![Anet A8 Sensor Bracket by Jako124](/t/8747956.jpg)
Anet A8 Sensor Bracket by Jako124
...t_probe_bed_position 25
define right_probe_bed_position 194
define back_probe_bed_position 170
define front_probe_bed_position 20
thingiverse
free
![Anet A8 - Blower & Sensor mount by InLineTwinNemesis](/t/8693266.jpg)
Anet A8 - Blower & Sensor mount by InLineTwinNemesis
... offset: -below +above [the nozzle]
also chanche this parameter in the configuration_h file: #define back_probe_bed_position 160
thingiverse
free
![Anet A8 Moving Fan Bracket by twistedfab13](/t/8647052.jpg)
Anet A8 Moving Fan Bracket by twistedfab13
... 220
define x_min_pos -33
define y_max_pos 220
define y_min_pos -10
define z_max_pos 240
define z_min_pos 0
thingiverse
free
![Right Side 18mm Sensor Anet A8 Stock by lordjg](/t/8700787.jpg)
Right Side 18mm Sensor Anet A8 Stock by lordjg
...t_probe_bed_position 42
define right_probe_bed_position 207
define back_probe_bed_position 200
define front_probe_bed_position 15
thingiverse
free
![Anet A8 12 mm front sensor fan mount Remix by MarkerDave](/t/8712619.jpg)
Anet A8 12 mm front sensor fan mount Remix by MarkerDave
...t_probe_bed_position 25
define right_probe_bed_position 194
define back_probe_bed_position 170
define front_probe_bed_position 20
thingiverse
free
![12 mm Sensor mount for Anet A6 by Askot](/t/8315081.jpg)
12 mm Sensor mount for Anet A6 by Askot
...-5 // y offset: -front +behind [the nozzle]
#define z_probe_offset_from_extruder 0 // z offset: -below +above [the nozzle]
Jmadison
thingiverse
free
![2020 Extrusion Cable Clip by JMadison](/t/8674448.jpg)
2020 Extrusion Cable Clip by JMadison
...trusion cable clip by jmadison
thingiverse
simple cable clip used to keep cables in place when running through a 2020 extrusion.
thingiverse
free
![Flat Cable Mounting Clip by JMadison](/t/8674437.jpg)
Flat Cable Mounting Clip by JMadison
...clip by jmadison
thingiverse
used to secure two 10 conductor flat cables.
uses a single m3 flathead screw.
print without support
thingiverse
free
![60mm Fan mount by JMadison](/t/8674452.jpg)
60mm Fan mount by JMadison
...an. no grill, only mounts to one side.
the fan mounting holes use 5mm fan screws. the 2 other mounting holes are for m3 screws.
thingiverse
free
![DIRECTV Genie mini mounting bracket by JMadison](/t/8730445.jpg)
DIRECTV Genie mini mounting bracket by JMadison
...genies and only the new model we got this year has this receptacle. the holes on the wall bracket are for #6/m3 flathead screws.
thingiverse
free
![2020 Extrusion Cable Tie Mounts by JMadison](/t/8723998.jpg)
2020 Extrusion Cable Tie Mounts by JMadison
...hese are designed for cable ties less than 3mm wide.
the hole is for m3 flathead screws.
these should be printed without support.
thingiverse
free
![UM2 Clone Power Switch Box by JMadison](/t/8674391.jpg)
UM2 Clone Power Switch Box by JMadison
...elf tapping flathead screws (other sizes will probably work)
snap in switch+receptacle: http://www.ebay.com/itm/like/221725745452
thingiverse
free
![ABS Fume filter by JMadison](/t/8753066.jpg)
ABS Fume filter by JMadison
...strong fan to push air through the larger capacity version. i found a 67cfm fan (or so it claims). i'll see how it performs.
thingiverse
free
![Anet A8 Switch Box by JMadison](/t/8749934.jpg)
Anet A8 Switch Box by JMadison
...ck nuts (or regular and use locktite)
(2) m3 nuts
other:
i didn't remove the power supply to take the photos, i have a spare.
thingiverse
free
![False Front Cabinet Clip by JMadison](/t/8727239.jpg)
False Front Cabinet Clip by JMadison
...e project i’m building i needed 16 of them and i’m too cheap to buy them. this version is slightly less beefy than the original.
thingiverse
free
![Ultimaker2 Clone Gantry Z Axis Top Remix by JMadison](/t/8674029.jpg)
Ultimaker2 Clone Gantry Z Axis Top Remix by JMadison
... also makes it easier to ream the 12mm holes because the holes go all the way through.
the locking screws are m3 x 8 button head.
Sn04
thingiverse
free
![RepRap Prusa Migbot MK8 Fan Mount SN04-N SN04-N2 by losinapetrovski](/t/8851855.jpg)
RepRap Prusa Migbot MK8 Fan Mount SN04-N SN04-N2 by losinapetrovski
...ap prusa migbot mk8 fan mount sn04-n sn04-n2 by losinapetrovski
thingiverse
prusa i3 migbot mk8 fan mount with sn04-n or sn04-n2
thingiverse
free
![SN04-N by UomoLibero](/t/8248858.jpg)
SN04-N by UomoLibero
...sn04-n by uomolibero
thingiverse
use it at your leisure.
thingiverse
free
![SN04-N Bracket and adjuster by fluxcore](/t/8102256.jpg)
SN04-N Bracket and adjuster by fluxcore
...sn04-n bracket and adjuster by fluxcore
thingiverse
i needed a adjuster and bracket for a sn04-n
thingiverse
free
![SN04-N Mount by Tgavan](/t/8753336.jpg)
SN04-N Mount by Tgavan
...van
thingiverse
simple sn04-n sensor mount with adjustable height.
designed to attach to http://www.thingiverse.com/thing:510957
thingiverse
free
![SN04 holder for Ei3 printer by olunak](/t/8784623.jpg)
SN04 holder for Ei3 printer by olunak
...sn04 holder for ei3 printer by olunak
thingiverse
easy to print holder for sn04 auto level probe.
thingiverse
free
![SN04 mount 40mm fan by Zupe](/t/8531898.jpg)
SN04 mount 40mm fan by Zupe
...sn04 mount 40mm fan by zupe
thingiverse
adjustable mount to sn04 autolevelsensor
fits to 40mm fan holes
thingiverse
free
![Athorbot Brother sn04 mount by phishtank](/t/8261165.jpg)
Athorbot Brother sn04 mount by phishtank
...athorbot brother sn04 mount by phishtank
thingiverse
i took the athorbot part fan stl and added an sn04 mount
thingiverse
free
![circular fan duct ring RepRap Prusa Migbot MK8 Fan Mount SN04-N SN04-N2 by losinapetrovski](/t/8848853.jpg)
circular fan duct ring RepRap Prusa Migbot MK8 Fan Mount SN04-N SN04-N2 by losinapetrovski
...fan mount sn04-n sn04-n2 by losinapetrovski
thingiverse
circular fan duct ring reprap prusa migbot mk8 fan mount sn04-n sn04-n2
thingiverse
free
![SN04 Z Adjuster HICTOP 3DP11 by parable](/t/8837804.jpg)
SN04 Z Adjuster HICTOP 3DP11 by parable
...sn04 z adjuster hictop 3dp11 by parable
thingiverse
micro-adjuster for z-axis sn04 proximity sensor.
thingiverse
free
![Dual Radial Fan Fang + SN04 by katolystic](/t/8710937.jpg)
Dual Radial Fan Fang + SN04 by katolystic
...dual radial fan fang + sn04 by katolystic
thingiverse
dual radial fan fang + sn04 remix from lion4h
Auto
thingiverse
free
![Auto sanitizer by Mandler_lim](/t/8087425.jpg)
Auto sanitizer by Mandler_lim
...auto sanitizer by mandler_lim
thingiverse
3d printed auto sanitizer
thingiverse
free
![Auto platform by vanne89](/t/8783365.jpg)
Auto platform by vanne89
...auto platform by vanne89
thingiverse
auto voor montessori college
thingiverse
free
![Feuerwehr Drachen Auto](/t/4867997.jpg)
Feuerwehr Drachen Auto
...feuerwehr drachen auto
thingiverse
feuerwehr auto mit drachen kopf spritze
thingiverse
free
![prueba auto 1 by davenezia](/t/8825518.jpg)
prueba auto 1 by davenezia
...prueba auto 1 by davenezia
thingiverse
prueba auto 1
thingiverse
free
![10mm Auto cartridge by Muhalo](/t/8949293.jpg)
10mm Auto cartridge by Muhalo
...10mm auto cartridge by muhalo
thingiverse
10mm auto cartridge.
thingiverse
free
![auto level probe by meSEA](/t/8926735.jpg)
auto level probe by meSEA
...auto level probe by mesea
thingiverse
auto level probe
thingiverse
free
![Auto Probe Tarantula Classic](/t/4765785.jpg)
Auto Probe Tarantula Classic
...auto probe tarantula classic
thingiverse
auto probe remix tarantula classic
thingiverse
free
![Auto alarm sensor handle](/t/4792760.jpg)
Auto alarm sensor handle
...auto alarm sensor handle
thingiverse
auto alarm audio sensor handle.
thingiverse
free
![robby by auto-bot](/t/8916552.jpg)
robby by auto-bot
...robby by auto-bot
thingiverse
steave
thingiverse
free
![zdxv by auto-bot](/t/8915322.jpg)
zdxv by auto-bot
...zdxv by auto-bot
thingiverse
vsd
N
thingiverse
free
![n/a by thingster](/t/9035101.jpg)
n/a by thingster
...n/a by thingster
thingiverse
n/a
thingiverse
free
![N by FallenEdge](/t/8935216.jpg)
N by FallenEdge
...n by fallenedge
thingiverse
a ribbon in the shape of an n
thingiverse
free
![N in 1 by cxam5](/t/8662447.jpg)
N in 1 by cxam5
...n in 1 by cxam5
thingiverse
n in 1
thingiverse
free
![N 3D by KySyth](/t/8805968.jpg)
N 3D by KySyth
...n 3d by kysyth
thingiverse
n 3d
thingiverse
free
![Part N by ZainK](/t/9028473.jpg)
Part N by ZainK
...part n by zaink
thingiverse
part n
thingiverse
free
![Letter N by fatherandson](/t/8096242.jpg)
Letter N by fatherandson
...letter n by fatherandson
thingiverse
the letter n print
thingiverse
free
![n-type cap](/t/4870148.jpg)
n-type cap
...n-type cap
thingiverse
n-type cap
thingiverse
free
![unown N abecedario](/t/4714901.jpg)
unown N abecedario
...unown n abecedario
thingiverse
unown n abecedario
thingiverse
free
![kubus by -N-](/t/8313803.jpg)
kubus by -N-
...kubus by -n-
thingiverse
requested
thingiverse
free
![n by shopper](/t/8837366.jpg)
n by shopper
...n by shopper
thingiverse
h
A8
thingiverse
free
![Direct Extruder for Anet A8 and A8+ with BMG by pedroamz](/t/8081319.jpg)
Direct Extruder for Anet A8 and A8+ with BMG by pedroamz
... for anet a8 and a8+ with bmg by pedroamz
thingiverse
extrusion conversion from anet a8 and a8 plus to bond tech "bmg"
thingiverse
free
![Audi A8 keychain](/t/4672207.jpg)
Audi A8 keychain
...audi a8 keychain
thingiverse
audi a8 keychain.
thingiverse
free
![Anet A8 Top Support Plate A8-0011 by swdave](/t/8255198.jpg)
Anet A8 Top Support Plate A8-0011 by swdave
... top support plate a8-0011 by swdave
thingiverse
anet a8 top support plate a8-0011
if yours is broken you can have it printed.
thingiverse
free
![a8 Leveling](/t/4893705.jpg)
a8 Leveling
...a8 leveling
thingiverse
leveling
thingiverse
free
![A8 by davidgutierrez](/t/8561111.jpg)
A8 by davidgutierrez
...a8 by davidgutierrez
thingiverse
bylin mold
thingiverse
free
![Filament Support A8](/t/4667339.jpg)
Filament Support A8
...filament support a8
thingiverse
my version of filament support for anet a8 printer.
thingiverse
free
![Anet A8, A8 plus and E16 Bltouch Probe Mounting by Kageler](/t/8007728.jpg)
Anet A8, A8 plus and E16 Bltouch Probe Mounting by Kageler
...ting by kageler
thingiverse
a bltouch probe mount for the anet a8, a8 plus and e16. i have used it on all these machines myself.
thingiverse
free
![Anet A8 Keychain by JUST3D_PRNTNG](/t/8577652.jpg)
Anet A8 Keychain by JUST3D_PRNTNG
...anet a8 keychain by just3d_prntng
thingiverse
a little anet a8 keychain or just a low detail model of the anet a8 printer.
thingiverse
free
![ANET A8 name by Sois](/t/8299963.jpg)
ANET A8 name by Sois
...anet a8 name by sois
thingiverse
anet a8 name
thingiverse
free
![ANET A8 Sign by sheldon056](/t/8313433.jpg)
ANET A8 Sign by sheldon056
...anet a8 sign by sheldon056
thingiverse
anet a8 sign
Anet
thingiverse
free
![Anet by derbodesign](/t/8641420.jpg)
Anet by derbodesign
...anet by derbodesign
thingiverse
logo anet
thingiverse
free
![Anet e10 , Anet v1.0 by jonathan_943D](/t/8288858.jpg)
Anet e10 , Anet v1.0 by jonathan_943D
...anet e10 , anet v1.0 by jonathan_943d
thingiverse
soporte de ventilador de 80mm, para controladora anet v1.0
thingiverse
free
![Anet A8 Anet AM8 Y belt holder](/t/4912219.jpg)
Anet A8 Anet AM8 Y belt holder
...anet a8 anet am8 y belt holder
thingiverse
anet a8 anet am8 y belt holder
thingiverse
free
![Anet A8 Probe Bracket for anet sensor by chelrix](/t/8786612.jpg)
Anet A8 Probe Bracket for anet sensor by chelrix
...anet a8 probe bracket for anet sensor by chelrix
thingiverse
anet a8 probe bracket for anet official sensor and marlin firmware
thingiverse
free
![Anet logo by JUST3D_PRNTNG](/t/8579602.jpg)
Anet logo by JUST3D_PRNTNG
...anet logo by just3d_prntng
thingiverse
anet logo
thingiverse
free
![Fan nozzle for Anet A8 with original Anet levelsensor by peteruhlmann](/t/8733915.jpg)
Fan nozzle for Anet A8 with original Anet levelsensor by peteruhlmann
...et levelsensor by peteruhlmann
thingiverse
here is an improved fan nozzle for the anet a8 with original level sensor from anet.
thingiverse
free
![Anet Et4 Box](/t/5000253.jpg)
Anet Et4 Box
...anet et4 box
thingiverse
tool box for anet et4
thingiverse
free
![Anet Logo by Superflex_Plastic_Fantastic](/t/8659775.jpg)
Anet Logo by Superflex_Plastic_Fantastic
...anet logo by superflex_plastic_fantastic
thingiverse
anet logo to incorporate into designs.
thingiverse
free
![Box for Anet ET4](/t/4678175.jpg)
Box for Anet ET4
...box for anet et4
thingiverse
this is a simple box for tool of anet et4
thingiverse
free
![Anet V1.0 Board Kühlung (80mm Lüfter) / Anet A8 by MadCre8](/t/8753212.jpg)
Anet V1.0 Board Kühlung (80mm Lüfter) / Anet A8 by MadCre8
...anet v1.0 board kühlung (80mm lüfter) / anet a8 by madcre8
thingiverse
anet v1.0 board kühlung (80mm lüfter) / anet a8
Sensor
thingiverse
free
![Xiaomi water sensor in door sensor](/t/4834090.jpg)
Xiaomi water sensor in door sensor
...xiaomi water sensor in door sensor
thingiverse
xiaomi water sensor in door sensor
thingiverse
free
![Sensor holder for Tekscan B201 sensor by ryanharold](/t/9248005.jpg)
Sensor holder for Tekscan B201 sensor by ryanharold
...sensor holder for tekscan b201 sensor by ryanharold
thingiverse
holder for a tekscan b201 sensor
thingiverse
free
![Sensor mount for Baumer Sensors by williab86](/t/8638976.jpg)
Sensor mount for Baumer Sensors by williab86
...mount for baumer sensors by williab86
thingiverse
basic baumer o300/o500 sensor mount. i added tie down points for the cabling.
thingiverse
free
![filament width sensor and runout sensor hall sensor based](/t/4793917.jpg)
filament width sensor and runout sensor hall sensor based
...o
hall sensor ss49e - 2pc
5x2mm magnet
f623zz bearing - 2pc
spring from atomatic pen
calibration pins, i use 1.5mm and 2 mm drill
thingiverse
free
![sensor mount for stock anet sensor by Frazor](/t/8731061.jpg)
sensor mount for stock anet sensor by Frazor
...sensor mount for stock anet sensor by frazor
thingiverse
custom sensor mount in front of the fan.
thingiverse
free
![bullet sensor](/t/4912239.jpg)
bullet sensor
...the bullet tube.
i found a cheaper compact sensor and provided the wiring.
the sensor might help out more projects you might have
thingiverse
free
![Filament Sensor and Cover (OEM sensor) by steverjuk](/t/8670117.jpg)
Filament Sensor and Cover (OEM sensor) by steverjuk
...sensor and cover (oem sensor) by steverjuk
thingiverse
remix version that will work with the sensor that comes with the oem kit.
thingiverse
free
![no sensor by montylpettit](/t/8540568.jpg)
no sensor by montylpettit
...no sensor by montylpettit
thingiverse
just a quick mod to remove the bed leveling sensor.
thingiverse
free
![sensor cover for niko indoor sensor mod by falken_X](/t/8846935.jpg)
sensor cover for niko indoor sensor mod by falken_X
...sensor cover for niko indoor sensor mod by falken_x
thingiverse
sensor limit view
thingiverse
free
![Sensor Bracket](/t/4668560.jpg)
Sensor Bracket
...iter between arms, requires longer bolts through exciter/ brass so that they can pass through sensor bracket and secured by nuts.
Leveling
thingiverse
free
![a8 Leveling](/t/4893705.jpg)
a8 Leveling
...a8 leveling
thingiverse
leveling
thingiverse
free
![level by Simirinojka](/t/8650908.jpg)
level by Simirinojka
...level by simirinojka
thingiverse
level
thingiverse
free
![Level by abies4](/t/8698363.jpg)
Level by abies4
...level by abies4
thingiverse
just a level, nothing special
thingiverse
free
![Fortnite levels](/t/4734274.jpg)
Fortnite levels
...fortnite levels
thingiverse
this are some fortnite badges according to gamer levels
thingiverse
free
![Leveling test](/t/4769766.jpg)
Leveling test
...leveling test
thingiverse
this is a leveling test. i used it on 150x150 print bed.
thingiverse
free
![Cutter level by yuriy_syvakov](/t/8533848.jpg)
Cutter level by yuriy_syvakov
...cutter level by yuriy_syvakov
thingiverse
cutter level for lathe. have to glue a bubble level
thingiverse
free
![Lobed leveling knob for the i3 by Leveller](/t/8740187.jpg)
Lobed leveling knob for the i3 by Leveller
...it plate and features extended lobes to make dialing in using a finger and thumb much easier than the tradtional knurled version.
thingiverse
free
![Bubble Level by MarcosMorCan](/t/8115134.jpg)
Bubble Level by MarcosMorCan
...bubble level by marcosmorcan
thingiverse
this is a simple bubble level. it holds 35mmx8mm level bubbles, i found in on internet.
thingiverse
free
![Scope Level by KeiserZA](/t/8759015.jpg)
Scope Level by KeiserZA
...scope level by keiserza
thingiverse
25mm scope level with bubble level space of 10mm by 6mm.
crude design
thingiverse
free
![Tile leveling by Buterbroder](/t/8348972.jpg)
Tile leveling by Buterbroder
...tile leveling by buterbroder
thingiverse
treaded tile leveling
Bracket
thingiverse
free
![Dual ESCape bracket and mounting bracket](/t/4925077.jpg)
Dual ESCape bracket and mounting bracket
...dual escape bracket and mounting bracket
thingiverse
dual escape bracket and mounting bracket ;)
thingiverse
free
![Bracket bracket by Psyense](/t/8588920.jpg)
Bracket bracket by Psyense
...ade a bracket for the bracket, found another peice of threaded rod, and doubled by spool capacity with no more holes in the wall.
thingiverse
free
![T - Bracket / Pipe Bracket by Sun_Dancer78](/t/8366556.jpg)
T - Bracket / Pipe Bracket by Sun_Dancer78
...t - bracket / pipe bracket by sun_dancer78
thingiverse
t-bracket for 25mm pipe on 20mm pipe
thingiverse
free
![bracket by a201900](/t/8163857.jpg)
bracket by a201900
...bracket by a201900
thingiverse
bracket
thingiverse
free
![L Bracket](/t/4868410.jpg)
L Bracket
...l bracket
thingiverse
bracket
thingiverse
free
![Bracket by nmarquardt](/t/8743506.jpg)
Bracket by nmarquardt
...bracket by nmarquardt
thingiverse
bracket
thingiverse
free
![Bracket by Jaenne](/t/8636211.jpg)
Bracket by Jaenne
...bracket by jaenne
thingiverse
bracket.
thingiverse
free
![bracket by joestraws](/t/8811729.jpg)
bracket by joestraws
...bracket by joestraws
thingiverse
bracket
thingiverse
free
![bracket by jimatdurham](/t/8850894.jpg)
bracket by jimatdurham
...bracket by jimatdurham
thingiverse
bracket
thingiverse
free
![Bracket by davidstout](/t/8836012.jpg)
Bracket by davidstout
...bracket by davidstout
thingiverse
bracket