Thingiverse
Air Arms S410 magazine - .22 by jonnyg30
by Thingiverse
Last crawled date: 3 years, 1 month ago
Complete replacement/spare 10 shot magazine for the Air Arms s410.
I finally managed to finish it!! the version 2 mag housing and mag cover with the V1 mag barrel are a complete success and I can happily say it's working just as good as the original!
UPDATE: I've been testing these mags for a little while now and all seems pretty good with them, all still working just as good as the original with no problems.
Mag barrel:
Printed in Hobbyking ABS with a 0.2mm nozzle at 0.1mm layer height, 20mm/s extrusion 230 degC, bed 100C using ABS slurry. It will "work" with a 0.4mm nozzle but i found the 0.2mm gave far superior results, minimal post processing and greater dimensional accuracy. Print with supports for the cut outs, PLA can be printed in current orientation but I found flipping it 180deg for ABS gave better cut outs for the o-ring.
Mag housing:
Printed in VANGogh ABS, 0.4mm nozzle, 0.2mm layer height, 240C EXT, 100C bed. must be printed with supports in supplied orientation, highly recommend using support roof with at least 3 layers to give best results. For ABS increase all axis by 1%, PLA, print at standard size.
Mag cover:
printed in VANGogh ABS, 0.4mm Nozzle, 0.2mm layer height, 240C EXT, 100C bed. no supports necessary and print in supplied orientation. For ABS, increase all axis by 1%, for PLA, print as is.
Post processing and build:
clean up all parts as necessary with a fine file/ sand paper. ensure all pellet holes in mag barrel are clear of protrusions, a .22 pellet should drop strait through the hole but equally it shouldn't be too baggy if you have got it right.
fit barrel to mag housing and check the rotation, it should spin with very slight friction and no snagging (I found mine were catching slightly on the lower R/H opening of the mag housing but a couple of file strokes were all that was needed).
Fit cover to housing and test fit to rifle, you will need to file/sand the rear of the mag housing until you get a nice "snug" fit (an unfortunate side effect of having to use supports for this job).
once you're happy with the fit and you have tested to ensure the mag cycles correctly, remove the mag barrel and fit an O-ring (i'm using the original AA mag O-rings pt/no: S556, (they cost me £3 for 10 off ebay). re-fit barrel into the mag housing and rotate the mag barrel so a detent lines up with the spring retainer. Drop a 4mm steel BB into the spring retainer. I found the correct size springs hard to find so I bought a 20mm long, 4mm O/D, 0.5mm carbon steel wire spring and cut it down into 6mm lengths (to be honest i could get away with shortening the spring a bit as mine is producing a bit too much force) other springs will work but you will need to experiment. when fitted, the mag should not take too much effort to index.
Refit the mag housing cover and secure with a short countersunk head self tapping screw (the hole is 3mm so it's your choice of screw), ensure the screw head is completely flush or below the surface of the mag housing cover or you'll do some damage to your rifle!
If you make one, please click the "made one" button and upload your results I'd love to see how others turn out, i'm thinking of printing some red or florescent ones for using at the range so it's easy to see a mag is fitted and I'm also going to try printing a mag barrel in glow in the dark ABS to see if it's possible to determine shots left without using a torch.....may even try a wood fill casing! and if you come across any issues please let me know and I'll do my best to help out enjoy!
I finally managed to finish it!! the version 2 mag housing and mag cover with the V1 mag barrel are a complete success and I can happily say it's working just as good as the original!
UPDATE: I've been testing these mags for a little while now and all seems pretty good with them, all still working just as good as the original with no problems.
Mag barrel:
Printed in Hobbyking ABS with a 0.2mm nozzle at 0.1mm layer height, 20mm/s extrusion 230 degC, bed 100C using ABS slurry. It will "work" with a 0.4mm nozzle but i found the 0.2mm gave far superior results, minimal post processing and greater dimensional accuracy. Print with supports for the cut outs, PLA can be printed in current orientation but I found flipping it 180deg for ABS gave better cut outs for the o-ring.
Mag housing:
Printed in VANGogh ABS, 0.4mm nozzle, 0.2mm layer height, 240C EXT, 100C bed. must be printed with supports in supplied orientation, highly recommend using support roof with at least 3 layers to give best results. For ABS increase all axis by 1%, PLA, print at standard size.
Mag cover:
printed in VANGogh ABS, 0.4mm Nozzle, 0.2mm layer height, 240C EXT, 100C bed. no supports necessary and print in supplied orientation. For ABS, increase all axis by 1%, for PLA, print as is.
Post processing and build:
clean up all parts as necessary with a fine file/ sand paper. ensure all pellet holes in mag barrel are clear of protrusions, a .22 pellet should drop strait through the hole but equally it shouldn't be too baggy if you have got it right.
fit barrel to mag housing and check the rotation, it should spin with very slight friction and no snagging (I found mine were catching slightly on the lower R/H opening of the mag housing but a couple of file strokes were all that was needed).
Fit cover to housing and test fit to rifle, you will need to file/sand the rear of the mag housing until you get a nice "snug" fit (an unfortunate side effect of having to use supports for this job).
once you're happy with the fit and you have tested to ensure the mag cycles correctly, remove the mag barrel and fit an O-ring (i'm using the original AA mag O-rings pt/no: S556, (they cost me £3 for 10 off ebay). re-fit barrel into the mag housing and rotate the mag barrel so a detent lines up with the spring retainer. Drop a 4mm steel BB into the spring retainer. I found the correct size springs hard to find so I bought a 20mm long, 4mm O/D, 0.5mm carbon steel wire spring and cut it down into 6mm lengths (to be honest i could get away with shortening the spring a bit as mine is producing a bit too much force) other springs will work but you will need to experiment. when fitted, the mag should not take too much effort to index.
Refit the mag housing cover and secure with a short countersunk head self tapping screw (the hole is 3mm so it's your choice of screw), ensure the screw head is completely flush or below the surface of the mag housing cover or you'll do some damage to your rifle!
If you make one, please click the "made one" button and upload your results I'd love to see how others turn out, i'm thinking of printing some red or florescent ones for using at the range so it's easy to see a mag is fitted and I'm also going to try printing a mag barrel in glow in the dark ABS to see if it's possible to determine shots left without using a torch.....may even try a wood fill casing! and if you come across any issues please let me know and I'll do my best to help out enjoy!
Similar models
thingiverse
free
Tesla Model 3 Trunk spring cover
...layer, 0.4mm nozzle and print the lasts mm in vase mode with a 0.5mm wall width, 0.25mm, 0.4mm nozzle layer for a better quality.
thingiverse
free
Wheel with tire by fatbear666
...666
thingiverse
tire - tpu, 0.4mm nozzle, 0.2mm layer, 0.4mm wall tickness.
wheel - pla, 0.4mm nozzle, 0.2mm layer.
no supports.
thingiverse
free
Spring Clamp Pad by C47_3D
...
replacement part for broken pad from spring clamp
printed with supports with pet-g.
3 walls with 0.4mm nozzle
layer hight 0.2mm
thingiverse
free
PillBox by Jacorna
...illbox by jacorna
thingiverse
printed in printrbot simple 2014. 0.4mm nozzle 0.2mm layer pla. all necessary support is built in.
thingiverse
free
External Module Cover for Jumper T-Lite by bdwalker1
...-lite radio when it is not in use.
i printed in tpu with 0.4mm nozzle and 0.2mm layer height, and it fits and stays on very well.
thingiverse
free
Parametric aluminium extrusion covers (e.g. 2020) by sigxcpu
...y printer they came a little loose with scale factor 1, so i've bumped to 1.01 in the openscad design.
do not rotate them! :)
thingiverse
free
ANYCUBIC Kossel Delta Round Filament Cooler
...ozzle 0.4mm.
supports only from bad, because it will be very difficult remoove it from inside the cooler.
thats all. good luck :)
thingiverse
free
Platal Max 420
...al to smoke big boze.
enjoy and happy 420 great fellow.
i printed it with 0.2mm layers
genereted support with cura.
0.4mm nozzle.
thingiverse
free
Cartoon RTX 3080 by thingalew
... of the model only. planning on adding version with support in the model.
nozzle: 0.4mm
layer height: 0.2mm
wall thickness: 0.4mm
thingiverse
free
WaterLock by Jacorna
...y jacorna
thingiverse
printed in printrbot simple 2014. 0.4mm nozzle 0.2mm layer pla.
tried on 2.5 litres canister, perfect fit.
S410
thingiverse
free
Economical Spinning Spool Holder for Ender 3 by S410
... fit the materials you have. unfortunately you'll have to use freecad for that, since that is what i used to model the parts.
3dwarehouse
free
S410
...s410
3dwarehouse
skříň střední, úzka, rohová, police
3dwarehouse
free
S410-5 TRACK GREEN
...s410-5 track green
3dwarehouse
3dwarehouse
free
S410-4 COPPER PATINA
...s410-4 copper patina
3dwarehouse
3dwarehouse
free
S410-1 RIVER MIST
...s410-1 river mist
3dwarehouse
3dwarehouse
free
S410-7 EQUESTRIAN GREEN
...s410-7 equestrian green
3dwarehouse
3dwarehouse
free
S410-6 GREENER PASTURES
...s410-6 greener pastures
3dwarehouse
Jonnyg30
thingiverse
free
Remixed Meepo remote holder by jonnyg30
...break off's and improve longevity also cut back the base to give it a more interesting look and make some savings on filament
thingiverse
free
rotating mount chest rig remix by jonnyg30
...ner.
https://www.thingiverse.com/thing:1198982
printed in abs at 0.2mm layer height, 100% infill and acetone smoothed to finish.
thingiverse
free
Trampa charge port blank by jonnyg30
...0% infill. 20-25mins to print. the "t" was filled with paint afterwards and everything smoothed and polished to finish.
thingiverse
free
Remixed FTX vantage spoiler by jonnyg30
... how well it took the punishment. test printing a replacement spoiler mounting bracket i designed, will upload later if it works.
thingiverse
free
FrenzyIncarnate's Hydra 40mm fan cover -Remixed for better airflow by jonnyg30
...up the support settings so it looks a little rough in the photos but i'm sure it's nothing a second attempt won't fix
thingiverse
free
Remixed QX95s battery bay/skids by jonnyg30
...inking was if i get other batteries i can just switch the the battery bay to match the battery size i want to use nice an easily.
thingiverse
free
Trampa motor light mount by jonnyg30
...mm layer height, 100% infill, no supports needed. as usually with smaller parts, slower is better. print time is around 15-20mins
thingiverse
free
Lay-Z-spa garden hose adapter by jonnyg30
... of the hose adapter.
use with the shortest length of hose you can as a long hose could cause too much back pressure on the pump.
thingiverse
free
Kral PB sling adaptors by jonnyg30
...ar stud on synthetic stocks, carry out the above off the rifle with the shaped nut. pilot drill the stock and then fit as normal.
thingiverse
free
Combust's hex spool holder - front cross bar with filament feed by jonnyg30
...to and everything fits with those dimensions) let me know and i'll have another go. also please let me know if it works too!!
Magazine
archibase_planet
free
Magazines
...ibase planet
magazine journal periodical magazines
magazines dual n200111 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Magazines
...magazines
archibase planet
magazine periodical journal
magazines - 3d model for interior 3d visualization.
3d_ocean
$5
3d magazine
...3d magazine
3docean
3d magazine book journal magazine newspaper
3d magazine model.
turbosquid
$2
magazines
...rbosquid
royalty free 3d model magazines for download as c4d on turbosquid: 3d models for games, architecture, videos. (1264164)
3d_export
$5
Magazine stand
...magazine stand
3dexport
magazine stand
3d_export
$5
magazine stand
...magazine stand
3dexport
magazine stand
3ddd
$1
Stool Magazine
...stool magazine
3ddd
stool magazine дизайнерское кресло
turbosquid
$10
magazine
...3d model magazine for download as max, max, max, fbx, and max on turbosquid: 3d models for games, architecture, videos. (1691943)
turbosquid
$2
Magazine
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
archive3d
free
Magazines 3D Model
...magazine periodical journal
magazines n160212 - 3d model (*.3ds) for interior 3d visualization.
22
3d_export
$25
rocks 22
...rocks 22
3dexport
rocks 3d model 22
turbosquid
$10
Luminaire - Lustre 22 22 Soleil
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
design_connected
$18
22 Bench
...22 bench
designconnected
etel interiores 22 bench benches computer generated 3d model. designed by etel carmona.
design_connected
$16
22 Chair
...22 chair
designconnected
etel interiores 22 chair chairs computer generated 3d model. designed by etel carmona.
3d_export
$6
tap-22
...tap-22
3dexport
3ddd
$1
Радиатор 22 типа
...радиатор 22 типа
3ddd
радиатор
радиатор 22 типа
3ddd
free
22 tube amplifier
...22 tube amplifier
3ddd
усилитель
22 tube amplifier
turbosquid
$35
Bracelet 22
...osquid
royalty free 3d model bracelet 22 for download as 3dm on turbosquid: 3d models for games, architecture, videos. (1548228)
turbosquid
$20
jamb 22
...turbosquid
royalty free 3d model jamb 22 for download as max on turbosquid: 3d models for games, architecture, videos. (1403875)
turbosquid
$18
Earrings 22
...osquid
royalty free 3d model earrings 22 for download as 3dm on turbosquid: 3d models for games, architecture, videos. (1548880)
Arms
archibase_planet
free
Arm
...ase planet
arm hand right hand skeleton
arm human skeleton right arm n030515 - 3d model (*.gsm+*.3ds+*.max) for 3d visualization.
3ddd
$1
arm chair
...arm chair
3ddd
arm chair , пуф
arm chair
turbosquid
$5
arm
...arm
turbosquid
royalty free 3d model arm for download as obj on turbosquid: 3d models for games, architecture, videos. (1306158)
turbosquid
free
Arm
...arm
turbosquid
free 3d model arm for download as obj and fbx on turbosquid: 3d models for games, architecture, videos. (1346955)
turbosquid
$29
Arm
...osquid
royalty free 3d model arm for download as obj and fbx on turbosquid: 3d models for games, architecture, videos. (1382436)
3d_export
$5
coat of arms
...coat of arms
3dexport
coat of arms
3ddd
$1
ARM SOFA
...arm sofa
3ddd
arm sofa
3ddd
$1
Arm chair
...arm chair
3ddd
arm chair
3ddd
$1
Arm chair
...arm chair
3ddd
угловое
arm chair
3ddd
$1
ARM CHAIR
...arm chair
3ddd
arm chair clothes
Air
3ddd
$1
Calligaris air
...calligaris air
3ddd
air , calligaris
cтул calligaris air
3ddd
$1
Air freshener
...air freshener
3ddd
air freshener , освежитель
air freshener
design_connected
$16
Air
...air
designconnected
flexform air lounge chairs computer generated 3d model. designed by antonio citterio.
turbosquid
$250
Heat pump air air
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
air
...air
3dexport
3ddd
$1
Кухня AIR
...кухня air
3ddd
air , мария
кухня air фабрики "мария"
3ddd
$1
Лампа AIR
...лампа air
3ddd
boconcept , air
настольная лампа air, boconcept. в50½xø32см
3d_export
$40
air deflector
...air deflector
3dexport
air deflector
3d_export
$15
air purifier
...air purifier
3dexport
air purifier
3d_export
$5
macbook air
...macbook air
3dexport
macbook air