Thingiverse
Afinia H480 Stabilized Remodeling by imaicom
by Thingiverse
Last crawled date: 3 years, 1 month ago
The built-in FET is generating heat during operation of the extruder or bed. I added a fan and tried forced air cooling. As of now, fans are running on separate power supplies. Adhesive tape and 16 mm tapping screw are necessary for fixing.
Attachment of the connector of the extruder is weak, and contact becomes worse. It became to fail to adjust the temperature of the extruder. It became shorter by about 1 cm, but stabilized by crimping 16P connector. To make it easier to pull out the connector, I attached a tie wrap.
Cover is necessary for this printer because it may peel off when laminating. An expensive cover is not necessary. A plastic bag is enough. However, it is hard to see. So, I will combine an OHP sheet with a polyethylene bag. Be careful not to cover the main board below. There is a problem with heat dissipation. Just pinching it in clothespins is enough.
The built-in SD card is 4 GB. In my printer SunDisk's one was used. Although it depends on the printer, since the SD card slot is manually soldered, there is a difference in proficiency by the operator. Due to this defect of soldering, an error may occur that the SD card can not read / write. It may be necessary to redo the soldering by experts. Repair by an amateur is actually simple, restoring by slightly deforming the soldered part of the SD card slot with a pin. It becomes a technique to mechanically deform the soldered part. Reliability according to crimping can be secured. The SD card itself can be used if you purchase a commercial product as it is and stab it. FAT16 would be a good format. Once height adjustment is done, it is recorded on the SD card. According to my trial and error, 8GB SD card could be used without problem. 32GB SD card was full of errors and could not be used.
The last picture is an example of fixing so that the bed does not come down.
Attachment of the connector of the extruder is weak, and contact becomes worse. It became to fail to adjust the temperature of the extruder. It became shorter by about 1 cm, but stabilized by crimping 16P connector. To make it easier to pull out the connector, I attached a tie wrap.
Cover is necessary for this printer because it may peel off when laminating. An expensive cover is not necessary. A plastic bag is enough. However, it is hard to see. So, I will combine an OHP sheet with a polyethylene bag. Be careful not to cover the main board below. There is a problem with heat dissipation. Just pinching it in clothespins is enough.
The built-in SD card is 4 GB. In my printer SunDisk's one was used. Although it depends on the printer, since the SD card slot is manually soldered, there is a difference in proficiency by the operator. Due to this defect of soldering, an error may occur that the SD card can not read / write. It may be necessary to redo the soldering by experts. Repair by an amateur is actually simple, restoring by slightly deforming the soldered part of the SD card slot with a pin. It becomes a technique to mechanically deform the soldered part. Reliability according to crimping can be secured. The SD card itself can be used if you purchase a commercial product as it is and stab it. FAT16 would be a good format. Once height adjustment is done, it is recorded on the SD card. According to my trial and error, 8GB SD card could be used without problem. 32GB SD card was full of errors and could not be used.
The last picture is an example of fixing so that the bed does not come down.
Similar models
thingiverse
free
Ender 3 Front screen with Fan Cover and SD card slot
...ard slot
thingiverse
reduce the space the printer takes on the right side
slot for sd card adapter
fan cover built-in as a mount
thingiverse
free
Artillery_X1_USB Cover With Slot by MoldyBlueBerry
...rd slot sticks out on my printer causing the cover to not sit flush. i added a cutout for the sd card slot and now it sits flush.
thingiverse
free
SD card cover by BaoTriet
...card covers were broken.therefore, i design it to help others fix their sd card instead of throw it out.
super glue is necessary.
cg_trader
$5
Ultimaker 2 SD-card cover block | 3D
...ver block | 3d
cg trader
this fits onto the boards of the ultimaker 2 printer and covers it's sd slot protecting the sd card
grabcad
free
micro SD Card Slot
...slot
grabcad
i modeled this connector up for use in altium designer.
the metal cover was designed using sheet metal techniques.
thingiverse
free
Artillery Genius SD Card Cover by TheLoneExtruder
...articularly useful when a usb extension cable is permanently attached to the printer, as the usb plug secures the cover in place.
thingiverse
free
Caddx Turtle v2 SD Card Slot Cover
...caddx turtle v2 sd card slot cover
thingiverse
caddx turtle v2 sd card slot cover
thingiverse
free
DELL SD Card Slot insert cover by AZDawg
...dell sd card slot insert cover by azdawg
thingiverse
i used the sd card and added the cover part to fit my dell laptop.
thingiverse
free
3D Printer Stabilizers by tfarms2
...3d printer stabilizers by tfarms2
thingiverse
use to stabilize heating element to fan
thingiverse
free
Ender 3 SD Card Cover for Cable by KTMan77
...card slot on a stock ender 3 pro where you have a remote sd card reader using a micro sd to sd cable.
this is a work in progress.
H480
3ddd
$1
Favourite 1023-5P
...1023-5p 3ddd favourite , om 1023-5p люстра размер светильника: d580*h480 лампы: 5*e14*60w цвет, отделка: античная бронза, хрусталь...
3ddd
$1
Favourite 1063-5P
...1063-5p 3ddd favourite , om 1063-5p люстра размер светильника: d580*h480 лампы: 5*e14*60w цвет, отделка: 24k позолота, хрусталь...
3ddd
$1
Favourite 1197-5P люстра
...люстра 3ddd favourite , om 1197-5p люстра размер светильника: d630*h4801000 лампы: e14*5*40w цвет, отделка: металл цвета слоновой кости, ткань...
3ddd
$1
Favourite 1196-5P люстра
...люстра 3ddd om , favourite 1196-5p люстра размер светильника: d630*h4801000 лампы: e14*5*40w цвет, отделка: металл цвета слоновой кости, ткань...
3ddd
$1
Favourite 1070-4P
...3ddd favourite , om 1070-4p люстра потолочная размер светильника: l550*w550*h480880max лампы: 4*e27*40w цвет, отделка: мебельное румынское дерево высшего качества,...
thingiverse
free
Afinia H480 X Axis Piece by atr27
...afinia h480 x axis piece by atr27
thingiverse
es una pieza de la impresora 3d del benjamin franklin science corner.
thingiverse
free
Afinia H480 Filament Feeder Guide by imaicom
...a version using 6 mm length hex screw with m3. be careful not to drop the bearing as it is not fixed at the time of installation.
thingiverse
free
Afinia H480 1kg Spool Holder by Odinfinity
...or other suitable downloads, and decided to mock up my own. i currently have this on the printer and it fits and works perfectly.
thingiverse
free
Afinia h480 Extruder Upgrade Upgrade by openrobot
... the shroud ... it has messed up geometry.. how do i optimize stl from max :d ?
print it on 10000% fill at super amazing quality
thingiverse
free
Afinia H479/H480 SphereAF Webcam Mount UP! by Lozercoward
...bcam mount up! by lozercoward
thingiverse
this webcam mount was created for a logitech sphere af. tested on a afinia h479 model.
Afinia
thingiverse
free
afinia filament cleaner by hdirim
...afinia filament cleaner by hdirim
thingiverse
afinia filament cleaner
thingiverse
free
UP PLUS2 (AFINIA) COVER by K_Design
... (afinia) cover by k_design
thingiverse
up plus2 (afinia) cover
a little bit of difference for afinia.
(near spool holder)
thingiverse
free
UP! / Afinia Speaker Cover by walter
...cover by walter
thingiverse
small cover for reducing the volume of the up! plus or afinia speaker
filament:
-- afinia orange abs
thingiverse
free
Afinia H800 3D Printer Model by ReginaFabricam
...verse
this is a model of an afinia h800 printer i saw at a fablab.https://www.tinkercad.com/things/jymd6ipqrys-3d-printer-afinia
thingiverse
free
Afinia 3d Printer plate clips by Youblurred
...afinia 3d printer plate clips by youblurred
thingiverse
the clips go on the sides of the board. for afinia 479 printers.
thingiverse
free
Afinia LED Light Holder by Kickthefog
...verse
left and right mounts for the afinia 3d printer that hold superbright led bar's to light the print surface / extruder.
thingiverse
free
Afinia Cardboard Spool Clip by ThingHuxter
... an alteration of walter's filament spool clip. this one, however, is intended to fit the afinia value line cardboard spools.
thingiverse
free
Soporte Bobina para Afinia y PP3DP by Osanchis
...soporte bobina para afinia y pp3dp by osanchis
thingiverse
soporte filamento para impresora afinia y pp3dp
thingiverse
free
Afinia Extruder Bearing Holder by Matt_C1
...ng holder/filament guide in an afinia h480 printer. i created it to give just a little more bite on materials like petg and abs.
thingiverse
free
UP! Plus / Afinia Sliding Perfboard Mod by mb20music
...perfboard mod by mb20music
thingiverse
this makes attaching the perfboard faster and easier on the up! plus and afinia printers.
Imaicom
thingiverse
free
*onigiriStand by imaicom
...ter.com/imaicom/status/1295928417146159105https://twitter.com/imaicom/status/1296017007184244737
https://denshiman.com/hinge.html
thingiverse
free
*latch80mm by imaicom
...*latch80mm by imaicom
thingiverse
https://twitter.com/imaicom/status/1294812335538872320
thingiverse
free
*doorStopper by imaicom
...*doorstopper by imaicom
thingiverse
https://twitter.com/imaicom/status/1299654106882207744
thingiverse
free
omni60mm by imaicom
...7817353216https://twitter.com/imaicom/status/1293682176362287104
https://denshiman.com/mg995.htmlhttps://denshiman.com/robot.html
thingiverse
free
omni50mm by imaicom
...7817353216https://twitter.com/imaicom/status/1293682176362287104
https://denshiman.com/mg995.htmlhttps://denshiman.com/robot.html
thingiverse
free
YWing3mm by imaicom
...ywing3mm by imaicom
thingiverse
https://twitter.com/imaicom/status/1294232591701143553
https://denshiman.com/toy.html
thingiverse
free
*GearTEST by imaicom
...*geartest by imaicom
thingiverse
https://twitter.com/imaicom/status/1297137906721710081
https://denshiman.com/toy.html
thingiverse
free
YWing2mm by imaicom
...ywing2mm by imaicom
thingiverse
https://twitter.com/imaicom/status/1294232591701143553
https://denshiman.com/toy.html
thingiverse
free
XWing3mm by imaicom
...itter.com/imaicom/status/1291652922955063296https://twitter.com/imaicom/status/1292288678845267969
https://denshiman.com/toy.html
thingiverse
free
*LMGuide220Slider by imaicom
...hingiverse
https://twitter.com/imaicom/status/1297309242106363905
https://denshiman.com/cnc.htmlhttps://denshiman.com/robot.html
Remodeling
3d_ocean
$45
Bathroom remodel
...bathroom remodel
3docean
bathroom interior
3d file ready to render with 4 camera views
turbosquid
$12
fireplace layout (home remodeling)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$22
bathroom layout 1 (home remodeling)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$22
bathroom layout 2 (home remodeling)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$10
hot water tank gas
...this model was created for the use in residential remodeling to aid and to assist in the plumbing system...
3d_export
$10
hot water tank electric
...this model was created for the use in residential remodeling to aid and to assist in the plumbing system...
3d_export
$5
dwv tee
...this model was created for the use in residential remodeling to aid and to assist in the plumbing system...
3d_export
$5
dwv closet bend
...this model was created for the use in residential remodeling to aid and to assist in the plumbing system...
3d_export
$39
Dinner set 3D Model
...3d model 3dexport kitchen food plate spoon knife kitchen remodeling ideas decor bulk dinner plates tableware dinner set 3d...
3ddd
$1
microphone SHURE SH 55
...crophone
i've remodelled main part of model (from 100 000 polys to 25 000 polys). i hope this time it's better.
greetings
Stabilized
3d_export
$5
Stabilizer 3D Model
...stabilizer 3d model
3dexport
stabilizer dashpot
stabilizer 3d model gaj15 60446 3dexport
turbosquid
$1
Steadicam Stabilizer
...oyalty free 3d model steadicam stabilizer for download as ipt on turbosquid: 3d models for games, architecture, videos. (1306615)
3d_export
free
Download free Stabilizer 3D Model
...download free stabilizer 3d model
3dexport
stabilizer electronics
stabilizer 3d model umairahmad555 35737 3dexport
3d_export
$23
stabilized moss and mirrors
...smoothing modifier is turned off by default. for close-ups, apply turbosmooth 1 iteration (turbosmooth is in the modifiers stack)
3d_export
$13
stabilized moss - world map
...level in the anti-aliasing modifier. the stack is open.<br>file export for anti-aliasing. apply the anti-aliasing modifier.
3d_export
$12
stone panels and stabilized moss
...in the scene).<br>all elements are made as separate objects, you can place them in any order<br>good renders for you!
3d_export
$13
wooden panels and stabilized moss
...r a particular frame. the anti-aliasing modifier is turned on (display in the viewport - 0 iterations, on the render 1 iteration)
3d_export
$13
stabilized moss 2
...or a particular frame. the anti-aliasing modifier is enabled (display in the viewport - 0 iterations, on the render 1 iteration).
3d_export
$13
stabilized moss 3
...level in the anti-aliasing modifier. the stack is open.<br>file export for anti-aliasing. apply the anti-aliasing modifier.
3d_export
$18
bouquet collection of dried flowers in a vase 181
...large: 260mm h x 140mm d solidago - dry, stabilized colored stems, dried pods, natural decor dry reed dried...